128 lines
4.3 KiB
Plaintext
128 lines
4.3 KiB
Plaintext
Console over Lightweight Link
|
|
=============================
|
|
|
|
LWL is a Lightweight bidirectional communication between target and debug host
|
|
without any need for additional hardware.
|
|
|
|
It works with openOCD and other debuggers that are capable of reading and
|
|
writing memory while the target is running...it should run with JLink
|
|
for example, if you've got the SDK and modify this file accordingly.
|
|
|
|
Principle of operation is simple; An 'upword' of 32 bits communicates
|
|
from the target to the host, a 'downword' of the same size runs in the
|
|
opposite direction. These two words can be in any memory that is
|
|
read/write access for both the target and the debug host. A simple ping
|
|
pong handshake protocol over these words allows up/down link communication.
|
|
On the upside no additional integration is needed. On the downside it may be
|
|
necessary to feed lwl with cycles to poll for changes in the downword,
|
|
depending on the use case. For the case of a simple console, that's not
|
|
needed.
|
|
|
|
For convenience these communication locations are automatically discovered
|
|
from the RAM by searching through it. Just define downwordaddr and
|
|
upwordaddr if you want to work with fixed locations.
|
|
|
|
Bit configuration
|
|
-----------------
|
|
|
|
Downword (Host to target);
|
|
|
|
A D U VV XXX O2 O1 O0
|
|
|
|
A 31 1 - Service Active (Set by host)
|
|
D 30 1 - Downsense (Toggled when there is data)
|
|
U 29 1 - Upsense ack (Toggled to acknowledge receipt of uplink data)
|
|
VV 28-27 2 - Valid Octets (Number of octets valid in the message)
|
|
XXX 26-24 3 - Port in use (Type of the message)
|
|
O2 23-16 8 - Octet 2
|
|
O1 15-08 8 - Octet 1
|
|
O0 07-00 8 - Octet 0
|
|
|
|
Upword (Target to Host);
|
|
|
|
A 31 1 - Service Active (Set by device)
|
|
D 30 1 - Downsense ack (Toggled to acknowledge receipt of downlink data)
|
|
U 29 1 - Upsense (Toggled when there is data)
|
|
VV 28-27 2 - Valid upword octets
|
|
XXX 26-24 3 - Port in use (Type of the message)
|
|
O2 23-16 8 - Octet 2
|
|
O1 15-08 8 - Octet 1
|
|
O0 07-00 8 - Octet 0
|
|
|
|
Port 1 is used for Console. No other ports are currently defined.
|
|
|
|
Usage
|
|
=====
|
|
|
|
No special python modules are needed, it should be possible to run the
|
|
application simply as shown below:
|
|
|
|
In the first terminal execute the openocd command to connect to the board.
|
|
Assuming that you already flashed to firmware (nuttx.bin) with the LWL
|
|
console support. For stm32f4discovery board I use this command:
|
|
|
|
------------------------------------------
|
|
$ sudo openocd -f board/stm32f4discovery.cfg
|
|
Open On-Chip Debugger v0.10.0-esp32-20200526-6-g4c41a632 (2020-06-23-10:12)
|
|
Licensed under GNU GPL v2
|
|
For bug reports, read
|
|
http://openocd.org/doc/doxygen/bugs.html
|
|
Info : The selected transport took over low-level target control. The results might differ compared to plain JTAG/SWD
|
|
srst_only separate srst_nogate srst_open_drain connect_deassert_srst
|
|
|
|
Info : Listening on port 6666 for tcl connections
|
|
Info : Listening on port 4444 for telnet connections
|
|
Info : clock speed 2000 kHz
|
|
Info : STLINK V2J17S0 (API v2) VID:PID 0483:3748
|
|
Info : Target voltage: 3.216252
|
|
Info : stm32f4x.cpu: hardware has 6 breakpoints, 4 watchpoints
|
|
Info : Listening on port 3333 for gdb connections
|
|
Info : accepting 'tcl' connection on tcp/6666
|
|
invalid command name "ocd_mdw"
|
|
0x20000000: 000000ff
|
|
|
|
0x20000000: 000000ff
|
|
|
|
0x20000004: 7216a318
|
|
|
|
0x2000000c: 994b5b1b
|
|
|
|
0x2000000c: 994b5b1b
|
|
|
|
0x2000000c: 994b5b1b
|
|
...
|
|
|
|
The "0x2000000c:..." will repeat all the time.
|
|
|
|
Now in another terminal execute:
|
|
|
|
------------------------------------------
|
|
$ ./ocdconsole.py
|
|
==Link Activated
|
|
|
|
nsh>
|
|
nsh> help
|
|
help usage: help [-v] [<cmd>]
|
|
|
|
? echo exit hexdump ls mh sleep xd
|
|
cat exec help kill mb mw usleep
|
|
nsh>
|
|
------------------------------------------
|
|
|
|
This code is designed to be 'hardy' and will survive a shutdown and
|
|
restart of the openocd process. When your target application
|
|
changes then the location of the upword and downword may change,
|
|
so they are re-searched for again. To speed up the start process
|
|
consider putting those words at fixed locations (e.g. via the
|
|
linker file) and referencing them directly.
|
|
|
|
Future work/Improvements
|
|
========================
|
|
|
|
Currently the lwl driver on NuttX side is doing polling, but for
|
|
better performance it could use interrupts to detect when the memory
|
|
position was modified to read the data.
|
|
|
|
It also will avoid using busy waiting inside the driver, look at
|
|
nuttx/arch/arm/src/common/arm_lwl_console.c for more information.
|