incubator-nuttx

History

Gregory Nutt 873de7b480 configs/*/README.txt: Update to the new URL for obtaining the ARM toolchain.		2017-08-13 07:18:19 -06:00
..
dhcpd	stm32f429i-disco, stm3240g-eval, stm3220g-eval, stm3210e-eval: Eliminate duplicate Make.defs files.	2017-07-11 07:34:09 -06:00
ide	Remove minnsh configurations and support logic: up_getc() and lowinstream.	2016-12-13 18:01:23 -06:00
include	STM32 Timer: Generalize and extend calculation of per-timer pre-scaler value. Inspired by original proposal from Pierre-noel Bouteville.	2016-06-03 11:38:59 -06:00
nettest	stm32f429i-disco, stm3240g-eval, stm3220g-eval, stm3210e-eval: Eliminate duplicate Make.defs files.	2017-07-11 07:34:09 -06:00
nsh	stm32f429i-disco, stm3240g-eval, stm3220g-eval, stm3210e-eval: Eliminate duplicate Make.defs files.	2017-07-11 07:34:09 -06:00
nsh2	stm32f429i-disco, stm3240g-eval, stm3220g-eval, stm3210e-eval: Eliminate duplicate Make.defs files.	2017-07-11 07:34:09 -06:00
nxwm	stm32f429i-disco, stm3240g-eval, stm3220g-eval, stm3210e-eval: Eliminate duplicate Make.defs files.	2017-07-11 07:34:09 -06:00
scripts	stm32f429i-disco, stm3240g-eval, stm3220g-eval, stm3210e-eval: Eliminate duplicate Make.defs files.	2017-07-11 07:34:09 -06:00
src	Move CAN subsystem to its own directory and put device drivers there	2017-05-12 11:48:47 -03:00
telnetd	stm32f429i-disco, stm3240g-eval, stm3220g-eval, stm3210e-eval: Eliminate duplicate Make.defs files.	2017-07-11 07:34:09 -06:00
tools	Correct permmisions on executable scripts	2016-04-10 09:11:59 -06:00
Kconfig	Remove the configs/ directory	2015-06-29 13:12:29 -06:00
README.txt	configs/*/README.txt: Update to the new URL for obtaining the ARM toolchain.	2017-08-13 07:18:19 -06:00

README.txt

README
======

This README discusses issues unique to NuttX configurations for the
STMicro STM3220G-EVAL development board.

Contents
========

- Development Environment
- GNU Toolchain Options
- IDEs
- NuttX EABI "buildroot" Toolchain
- NuttX OABI "buildroot" Toolchain
- NXFLAT Toolchain
- STM3220G-EVAL-specific Configuration Options
- LEDs
- Ethernet
- PWM
- CAN
- FSMC SRAM
- I/O Expanders
- STM3220G-EVAL-specific Configuration Options
- Configurations

Development Environment
=======================

Linux, OS X or Cygwin on Windows can be used for the development environment.
The source has been built only using the GNU toolchain (see below). Other
toolchains will likely cause problems. Testing was performed using the Cygwin
environment because the Raisonance R-Link emulatator and some RIDE7 development tools
were used and those tools works only under Windows.

GNU Toolchain Options
=====================

Toolchain Configurations
------------------------
The NuttX make system has been modified to support the following different
toolchain options.

1. The CodeSourcery GNU toolchain,
2. The Atollic Toolchain,
3. The devkitARM GNU toolchain,
4. Raisonance GNU toolchain,
5. The NuttX buildroot Toolchain (see below), or
6. Any generic arm-none-eabi GNU toolchain.

Most testing has been conducted using the CodeSourcery toolchain for Windows and
that is the default toolchain in most configurations. To use the Atollic
devkitARM, Raisonance GNU, or NuttX buildroot toolchain, you simply need to
add one of the following configuration options to your .config (or defconfig)
file:

CONFIG_ARMV7M_TOOLCHAIN_CODESOURCERYW=y : CodeSourcery under Windows
CONFIG_ARMV7M_TOOLCHAIN_CODESOURCERYL=y : CodeSourcery under Linux
CONFIG_ARMV7M_TOOLCHAIN_ATOLLIC=y : The Atollic toolchain under Windows
CONFIG_ARMV7M_TOOLCHAIN_DEVKITARM=y : devkitARM under Windows
CONFIG_ARMV7M_TOOLCHAIN_RAISONANCE=y : Raisonance RIDE7 under Windows
CONFIG_ARMV7M_TOOLCHAIN_BUILDROOT=y : NuttX buildroot under Linux or Cygwin (default)
CONFIG_ARMV7M_TOOLCHAIN_GNU_EABIL : Generic arm-none-eabi toolchain

The toolchain may also be set using the kconfig-mconf utility (make menuconfig)
or by passing CONFIG_ARMV7M_TOOLCHAIN=<toolchain> to make, where <toolchain> is one
of CODESOURCERYW, CODESOURCERYL, ATOLLOC, DEVKITARM, RAISONANCE, BUILDROOT or
GNU_EABI as described above.

NOTE: the CodeSourcery (for Windows), Atollic, devkitARM, and Raisonance toolchains are
Windows native toolchains. The CodeSourcey (for Linux) and NuttX buildroot
toolchains are Cygwin and/or Linux native toolchains. There are several limitations
to using a Windows based toolchain in a Cygwin environment. The three biggest are:

1. The Windows toolchain cannot follow Cygwin paths. Path conversions are
performed automatically in the Cygwin makefiles using the 'cygpath' utility
but you might easily find some new path problems. If so, check out 'cygpath -w'

2. Windows toolchains cannot follow Cygwin symbolic links. Many symbolic links
are used in Nuttx (e.g., include/arch). The make system works around these
problems for the Windows tools by copying directories instead of linking them.
But this can also cause some confusion for you: For example, you may edit
a file in a "linked" directory and find that your changes had no effect.
That is because you are building the copy of the file in the "fake" symbolic
directory. If you use a Windows toolchain, you should get in the habit of
making like this:

make clean_context all

An alias in your .bashrc file might make that less painful.

The CodeSourcery Toolchain (2009q1)
-----------------------------------
The CodeSourcery toolchain (2009q1) does not work with default optimization
level of -Os (See Make.defs). It will work with -O0, -O1, or -O2, but not with
-Os.

The Atollic "Pro" and "Lite" Toolchain
--------------------------------------
One problem that I had with the Atollic toolchains is that the provide a gcc.exe
and g++.exe in the same bin/ file as their ARM binaries. If the Atollic bin/ path
appears in your PATH variable before /usr/bin, then you will get the wrong gcc
when you try to build host executables. This will cause to strange, uninterpretable
errors build some host binaries in tools/ when you first make.

The Atollic "Lite" Toolchain
----------------------------
The free, "Lite" version of the Atollic toolchain does not support C++ nor
does it support ar, nm, objdump, or objdcopy. If you use the Atollic "Lite"
toolchain, you will have to set:

CONFIG_HAVE_CXX=n

In order to compile successfully. Otherwise, you will get errors like:

"C++ Compiler only available in TrueSTUDIO Professional"

The make may then fail in some of the post link processing because of some of
the other missing tools. The Make.defs file replaces the ar and nm with
the default system x86 tool versions and these seem to work okay. Disable all
of the following to avoid using objcopy:

CONFIG_RRLOAD_BINARY=n
CONFIG_INTELHEX_BINARY=n
CONFIG_MOTOROLA_SREC=n
CONFIG_RAW_BINARY=n

devkitARM
---------
The devkitARM toolchain includes a version of MSYS make. Make sure that the
the paths to Cygwin's /bin and /usr/bin directories appear BEFORE the devkitARM
path or will get the wrong version of make.

Generic arm-none-eabi GNU Toolchain
-----------------------------------
There are a number of toolchain projects providing support for the Cortex-M
class processors, including:

GCC ARM Embedded
https://developer.arm.com/open-source/gnu-toolchain/gnu-rm

Thumb2 Newlib Toolchain
https://github.com/EliasOenal/TNT

Summon ARM Toolchain
https://github.com/esden/summon-arm-toolchain

Yagarto
http://www.yagarto.de

Others exist for various Linux distributions, MacPorts, etc. Any version
based on GCC 4.6.3 or later should work.

IDEs
====

NuttX is built using command-line make. It can be used with an IDE, but some
effort will be required to create the project.

Makefile Build
--------------
Under Eclipse, it is pretty easy to set up an "empty makefile project" and
simply use the NuttX makefile to build the system. That is almost for free
under Linux. Under Windows, you will need to set up the "Cygwin GCC" empty
makefile project in order to work with Windows (Google for "Eclipse Cygwin" -
there is a lot of help on the internet).

Native Build
------------
Here are a few tips before you start that effort:

1) Select the toolchain that you will be using in your .config file
2) Start the NuttX build at least one time from the Cygwin command line
before trying to create your project. This is necessary to create
certain auto-generated files and directories that will be needed.
3) Set up include pathes: You will need include/, arch/arm/src/stm32,
arch/arm/src/common, arch/arm/src/armv7-m, and sched/.
4) All assembly files need to have the definition option -D __ASSEMBLY__
on the command line.

Startup files will probably cause you some headaches. The NuttX startup file
is arch/arm/src/stm32/stm32_vectors.S. With RIDE, I have to build NuttX
one time from the Cygwin command line in order to obtain the pre-built
startup object needed by RIDE.

Export nuttx to IAR or uVision workspace
----------------------------------------
The script nuttx/tools/ide_exporter.py will help to create nuttx project in
these IDEs. Here are few simple the steps to export the IDE workspaces:

1) Start the NuttX build from the Cygwin command line before trying to
create your project by running:

make V=1 |& tee build_log

This is necessary to certain auto-generated files and directories that
will be needed. This will provide the build log to construct the IDE
project also.

2) Export the IDE project base on that make log. The script usage:

usage: ide_exporter.py [-h] [-v] [-o OUT_DIR] [-d] build_log {iar,uvision_armcc,uvision_gcc} template_dir

positional arguments:
build_log Log file from make V=1
{iar,uvision_armcc,uvision_gcc}
The target IDE: iar, uvision_gcc, (uvision_armcc is experimental)
template_dir Directory that contains IDEs template projects

optional arguments:
-h, --help show this help message and exit
-v, --version show program's version number and exit
-o OUT_DIR, --output OUT_DIR
Output directory
-d, --dump Dump project structure tree

Example:
cd nuttx
make V=1 |& tee build_log

./tools/ide_exporter.py makelog_f2nsh_c iar ./configs/stm3220g-eval/ide/template/iar -o ./configs/stm3220g-eval/ide/nsh/iar

./tools/ide_exporter.py makelog_f2nsh_c uvision_gcc ./configs/stm3220g-eval/ide/template/uvision_gcc/ -o ./configs/stm3220g-eval/ide/nsh/uvision

3) Limitations:
- IAR supports C only. Iar C++ does not compatible with g++ so disable
C++ if you want to use IAR.
- uvision_armcc : nuttx asm (inline and .asm) can't be compiled with
armcc so do not use this option.
- uvision_gcc : uvision project that uses gcc. Need to specify path to
gnu toolchain.
In uVison menu, select:

Project/Manage/Project Items.../FolderExtension/Use GCC compiler/ PreFix, Folder

4) Template projects' constrains:
- mcu, core, link script shall be configured in template project
- Templates' name are fixed:
- template_nuttx.eww : IAR nuttx workspace template
- template_nuttx_lib.ewp : IAR nuttx library project template
- template_nuttx_main.ewp : IAR nuttx main project template
- template_nuttx.uvmpw : uVision workspace
- template_nuttx_lib.uvproj : uVision library project
- template_nuttx_main.uvproj : uVision main project
- iar:
- Library option shall be set to 'None' so that IAR could use nuttx libc
- __ASSEMBLY__ symbol shall be defined in assembler
- uVision_gcc:
- There should be one fake .S file in projects that has been defined __ASSEMBLY__ in assembler.
- In Option/CC tab : disable warning
- In Option/CC tab : select Compile thump code (or Misc control = -mthumb)
- template_nuttx_lib.uvproj shall add 'Post build action' to copy .a file to .\lib
- template_nuttx_main.uvproj Linker:
- Select 'Do not use Standard System Startup Files' and 'Do not use Standard System Libraries'
- Do not select 'Use Math libraries'
- Misc control = --entry=__start

5) How to create template for other configurations:
1) uVision with gcc toolchain:
- Copy 3 uVision project files
- Select the MCU for main and lib project
- Correct the path to ld script if needed
2) iar:
- Check if the arch supportes IAR (only armv7-m is support IAR now)
- Select the MCU for main and lib project
- Add new ld script file for IAR

NuttX EABI "buildroot" Toolchain
================================

A GNU GCC-based toolchain is assumed. The PATH environment variable should
be modified to point to the correct path to the Cortex-M3 GCC toolchain (if
different from the default in your PATH variable).

If you have no Cortex-M3 toolchain, one can be downloaded from the NuttX
Bitbucket download site (https://bitbucket.org/nuttx/buildroot/downloads/).
This GNU toolchain builds and executes in the Linux or Cygwin environment.

1. You must have already configured Nuttx in <some-dir>/nuttx.

cd tools
./configure.sh stm3220g-eval/<sub-dir>

2. Download the latest buildroot package into <some-dir>

3. unpack the buildroot tarball. The resulting directory may
have versioning information on it like buildroot-x.y.z. If so,
rename <some-dir>/buildroot-x.y.z to <some-dir>/buildroot.

4. cd <some-dir>/buildroot

5. cp configs/cortexm3-eabi-defconfig-4.6.3 .config

6. make oldconfig

7. make

8. Make sure that the PATH variable includes the path to the newly built
binaries.

See the file configs/README.txt in the buildroot source tree. That has more
details PLUS some special instructions that you will need to follow if you are
building a Cortex-M3 toolchain for Cygwin under Windows.

NOTE: Unfortunately, the 4.6.3 EABI toolchain is not compatible with the
the NXFLAT tools. See the top-level TODO file (under "Binary loaders") for
more information about this problem. If you plan to use NXFLAT, please do not
use the GCC 4.6.3 EABI toochain; instead use the GCC 4.3.3 OABI toolchain.
See instructions below.

NuttX OABI "buildroot" Toolchain
================================

The older, OABI buildroot toolchain is also available. To use the OABI
toolchain:

1. When building the buildroot toolchain, either (1) modify the cortexm3-eabi-defconfig-4.6.3
configuration to use EABI (using 'make menuconfig'), or (2) use an exising OABI
configuration such as cortexm3-defconfig-4.3.3

2. Modify the Make.defs file to use the OABI conventions:

+CROSSDEV = arm-nuttx-elf-
+ARCHCPUFLAGS = -mtune=cortex-m3 -march=armv7-m -mfloat-abi=soft
+NXFLATLDFLAGS2 = $(NXFLATLDFLAGS1) -T$(TOPDIR)/binfmt/libnxflat/gnu-nxflat-gotoff.ld -no-check-sections
-CROSSDEV = arm-nuttx-eabi-
-ARCHCPUFLAGS = -mcpu=cortex-m3 -mthumb -mfloat-abi=soft
-NXFLATLDFLAGS2 = $(NXFLATLDFLAGS1) -T$(TOPDIR)/binfmt/libnxflat/gnu-nxflat-pcrel.ld -no-check-sections

NXFLAT Toolchain
================

If you are *not* using the NuttX buildroot toolchain and you want to use
the NXFLAT tools, then you will still have to build a portion of the buildroot
tools -- just the NXFLAT tools. The buildroot with the NXFLAT tools can
be downloaded from the NuttX Bitbucket download site
(https://bitbucket.org/nuttx/nuttx/downloads/).

This GNU toolchain builds and executes in the Linux or Cygwin environment.

1. You must have already configured Nuttx in <some-dir>/nuttx.

cd tools
./configure.sh lpcxpresso-lpc1768/<sub-dir>

2. Download the latest buildroot package into <some-dir>

3. unpack the buildroot tarball. The resulting directory may
have versioning information on it like buildroot-x.y.z. If so,
rename <some-dir>/buildroot-x.y.z to <some-dir>/buildroot.

4. cd <some-dir>/buildroot

5. cp configs/cortexm3-defconfig-nxflat .config

6. make oldconfig

7. make

8. Make sure that the PATH variable includes the path to the newly built
NXFLAT binaries.

Ethernet
========

The Ethernet driver is configured to use the MII interface:

Board Jumper Settings:

Jumper Description
JP8 To enable MII, JP8 should not be fitted.
JP6 2-3: Enable MII interface mode
JP5 2-3: Provide 25 MHz clock for MII or 50 MHz clock for RMII by MCO at PA8
SB1 Not used with MII

LEDs
====

The STM3220G-EVAL board has four LEDs labeled LD1, LD2, LD3 and LD4 on the
board.. These LEDs are not used by the board port unless CONFIG_ARCH_LEDS is
defined. In that case, the usage by the board port is defined in
include/board.h and src/up_leds.c. The LEDs are used to encode OS-related\
events as follows:

SYMBOL Meaning LED1* LED2 LED3 LED4
------------------- ----------------------- ------- ------- ------- ------
LED_STARTED NuttX has been started ON OFF OFF OFF
LED_HEAPALLOCATE Heap has been allocated OFF ON OFF OFF
LED_IRQSENABLED Interrupts enabled ON ON OFF OFF
LED_STACKCREATED Idle stack created OFF OFF ON OFF
LED_INIRQ In an interrupt** ON N/C N/C OFF
LED_SIGNAL In a signal handler*** N/C ON N/C OFF
LED_ASSERTION An assertion failed ON ON N/C OFF
LED_PANIC The system has crashed N/C N/C N/C ON
LED_IDLE STM32 is is sleep mode (Optional, not used)

* If LED1, LED2, LED3 are statically on, then NuttX probably failed to boot
and these LEDs will give you some indication of where the failure was
** The normal state is LED3 ON and LED1 faintly glowing. This faint glow
is because of timer interrupts that result in the LED being illuminated
on a small proportion of the time.
*** LED2 may also flicker normally if signals are processed.

PWM
===

The STM3220G-Eval has no real on-board PWM devices, but the board can be
configured to output a pulse train using timer output pins. The following
pins have been use to generate PWM output (see board.h for some other
candidates):

TIM4 CH2. Pin PD13 is used by the FSMC (FSMC_A18) and is also connected
to the Motor Control Connector (CN5) just for this purpose. If FSMC is
not enabled, then FSMC_A18 will not be used (and will be tri-stated from
the LCD).

CONFIGURATION:

CONFIG_STM32_TIM4=y
CONFIG_PWM=n
CONFIG_PWM_PULSECOUNT=n
CONFIG_STM32_TIM4_PWM=y
CONFIG_STM32_TIM4_CHANNEL=2

ACCESS:

Daughterboard Extension Connector, CN3, pin 32
Ground is available on CN3, pin1

NOTE: TIM4 hardware will not support pulse counting.

TIM8 CH4: Pin PC9 is used by the microSD card (MicroSDCard_D1) and I2S
(I2S_CKIN) but can be completely disconnected from both by opening JP16.

CONFIGURATION:

CONFIG_STM32_TIM8=y
CONFIG_PWM=n
CONFIG_PWM_PULSECOUNT=y
CONFIG_STM32_TIM8_PWM=y
CONFIG_STM32_TIM8_CHANNEL=4

ACCESS:

Daughterboard Extension Connector, CN3, pin 17
Ground is available on CN3, pin1

CAN
===

Connector 10 (CN10) is DB-9 male connector that can be used with CAN1 or CAN2.

JP10 connects CAN1_RX or CAN2_RX to the CAN transceiver
JP3 connects CAN1_TX or CAN2_TX to the CAN transceiver

CAN signals are then available on CN10 pins:

CN10 Pin 7 = CANH
CN10 Pin 2 = CANL

Mapping to STM32 GPIO pins:

PD0 = FSMC_D2 & CAN1_RX
PD1 = FSMC_D3 & CAN1_TX
PB13 = ULPI_D6 & CAN2_TX
PB5 = ULPI_D7 & CAN2_RX

Configuration Options:

CONFIG_CAN - Enables CAN support (one or both of CONFIG_STM32_CAN1 or
CONFIG_STM32_CAN2 must also be defined)
CONFIG_CAN_EXTID - Enables support for the 29-bit extended ID. Default
Standard 11-bit IDs.
CONFIG_CAN_FIFOSIZE - The size of the circular buffer of CAN messages.
Default: 8
CONFIG_CAN_NPENDINGRTR - The size of the list of pending RTR requests.
Default: 4

CONFIG_STM32_CAN1 - Enable support for CAN1
CONFIG_CAN1_BAUD - CAN1 BAUD rate. Required if CONFIG_STM32_CAN1 is defined.
CONFIG_STM32_CAN2 - Enable support for CAN2
CONFIG_CAN2_BAUD - CAN1 BAUD rate. Required if CONFIG_STM32_CAN2 is defined.
CONFIG_CAN_TSEG1 - The number of CAN time quanta in segment 1. Default: 6
CONFIG_CAN_TSEG2 - the number of CAN time quanta in segment 2. Default: 7
CONFIG_STM32_CAN_REGDEBUG - If CONFIG_DEBUG_FEATURES is set, this will generate an
dump of all CAN registers.

FSMC SRAM
=========

On-board SRAM
-------------

A 16 Mbit SRAM is connected to the STM32F407IGH6 FSMC bus which shares the same
I/Os with the CAN1 bus. Jumper settings:

JP1: Connect PE4 to SRAM as A20
JP2: onnect PE3 to SRAM as A19

JP3 and JP10 must not be fitted for SRAM and LCD application. JP3 and JP10
select CAN1 or CAN2 if fitted; neither if not fitted.

The on-board SRAM can be configured by setting

CONFIG_STM32_FSMC=y
CONFIG_STM32_FSMC_SRAM=y
CONFIG_HEAP2_BASE=0x64000000
CONFIG_HEAP2_SIZE=2097152
CONFIG_MM_REGIONS=2

Configuration Options
---------------------

Internal SRAM is available in all members of the STM32 family. In addition
to internal SRAM, SRAM may also be available through the FSMC. In order to
use FSMC SRAM, the following additional things need to be present in the
NuttX configuration file:

CONFIG_STM32_FSMC=y : Enables the FSMC
CONFIG_STM32_FSMC_SRAM=y : Indicates that SRAM is available via the
FSMC (as opposed to an LCD or FLASH).
CONFIG_HEAP2_BASE : The base address of the SRAM in the FSMC
address space
CONFIG_HEAP2_SIZE : The size of the SRAM in the FSMC
address space
CONFIG_MM_REGIONS : Must be set to a large enough value to
include the FSMC SRAM

SRAM Configurations
-------------------
There are 2 possible SRAM configurations:

Configuration 1. System SRAM (only)
CONFIG_MM_REGIONS == 1
Configuration 2. System SRAM and FSMC SRAM
CONFIG_MM_REGIONS == 2
CONFIG_STM32_FSMC_SRAM defined

I/O Expanders
=============

The STM3220G-EVAL has two STMPE811QTR I/O expanders on board both connected to
the STM32 via I2C1. They share a common interrupt line: PI2.

STMPE811 U24, I2C address 0x41 (7-bit)
------ ---- ---------------- --------------------------------------------
STPE11 PIN BOARD SIGNAL BOARD CONNECTION
------ ---- ---------------- --------------------------------------------
Y- TouchScreen_Y- LCD Connector XL
X- TouchScreen_X- LCD Connector XR
Y+ TouchScreen_Y+ LCD Connector XD
X+ TouchScreen_X+ LCD Connector XU
IN3 EXP_IO9
IN2 EXP_IO10
IN1 EXP_IO11
IN0 EXP_IO12

STMPE811 U29, I2C address 0x44 (7-bit)
------ ---- ---------------- --------------------------------------------
STPE11 PIN BOARD SIGNAL BOARD CONNECTION
------ ---- ---------------- --------------------------------------------
Y- EXP_IO1
X- EXP_IO2
Y+ EXP_IO3
X+ EXP_IO4
IN3 EXP_IO5
IN2 EXP_IO6
IN1 EXP_IO7
IN0 EXP_IO8

STM3220G-EVAL-specific Configuration Options
============================================

CONFIG_ARCH - Identifies the arch/ subdirectory. This should
be set to:

CONFIG_ARCH=arm

CONFIG_ARCH_family - For use in C code:

CONFIG_ARCH_ARM=y

CONFIG_ARCH_architecture - For use in C code:

CONFIG_ARCH_CORTEXM3=y

CONFIG_ARCH_CHIP - Identifies the arch/*/chip subdirectory

CONFIG_ARCH_CHIP=stm32

CONFIG_ARCH_CHIP_name - For use in C code to identify the exact
chip:

CONFIG_ARCH_CHIP_STM32F207IG=y

CONFIG_ARCH_BOARD_STM32_CUSTOM_CLOCKCONFIG - Enables special STM32 clock
configuration features.

CONFIG_ARCH_BOARD_STM32_CUSTOM_CLOCKCONFIG=n

CONFIG_ARCH_BOARD - Identifies the configs subdirectory and
hence, the board that supports the particular chip or SoC.

CONFIG_ARCH_BOARD=stm3220g_eval (for the STM3220G-EVAL development board)

CONFIG_ARCH_BOARD_name - For use in C code

CONFIG_ARCH_BOARD_STM3220G_EVAL=y

CONFIG_ARCH_LOOPSPERMSEC - Must be calibrated for correct operation
of delay loops

CONFIG_ENDIAN_BIG - define if big endian (default is little
endian)

CONFIG_RAM_SIZE - Describes the installed DRAM (SRAM in this case):

CONFIG_RAM_SIZE=0x00010000 (64Kb)

CONFIG_RAM_START - The start address of installed DRAM

CONFIG_RAM_START=0x20000000

In addition to internal SRAM, SRAM may also be available through the FSMC.
In order to use FSMC SRAM, the following additional things need to be
present in the NuttX configuration file:

CONFIG_STM32_FSMC_SRAM - Indicates that SRAM is available via the
FSMC (as opposed to an LCD or FLASH).

CONFIG_HEAP2_BASE - The base address of the SRAM in the FSMC address space (hex)

CONFIG_HEAP2_SIZE - The size of the SRAM in the FSMC address space (decimal)

CONFIG_ARCH_LEDS - Use LEDs to show state. Unique to boards that
have LEDs

CONFIG_ARCH_INTERRUPTSTACK - This architecture supports an interrupt
stack. If defined, this symbol is the size of the interrupt
stack in bytes. If not defined, the user task stacks will be
used during interrupt handling.

CONFIG_ARCH_STACKDUMP - Do stack dumps after assertions

CONFIG_ARCH_LEDS - Use LEDs to show state. Unique to board architecture.

CONFIG_ARCH_CALIBRATION - Enables some build in instrumentation that
cause a 100 second delay during boot-up. This 100 second delay
serves no purpose other than it allows you to calibratre
CONFIG_ARCH_LOOPSPERMSEC. You simply use a stop watch to measure
the 100 second delay then adjust CONFIG_ARCH_LOOPSPERMSEC until
the delay actually is 100 seconds.

Individual subsystems can be enabled:

AHB1
----
CONFIG_STM32_CRC
CONFIG_STM32_BKPSRAM
CONFIG_STM32_DMA1
CONFIG_STM32_DMA2
CONFIG_STM32_ETHMAC
CONFIG_STM32_OTGHS

AHB2
----
CONFIG_STM32_DCMI
CONFIG_STM32_CRYP
CONFIG_STM32_HASH
CONFIG_STM32_RNG
CONFIG_STM32_OTGFS

AHB3
----
CONFIG_STM32_FSMC

APB1
----
CONFIG_STM32_TIM2
CONFIG_STM32_TIM3
CONFIG_STM32_TIM4
CONFIG_STM32_TIM5
CONFIG_STM32_TIM6
CONFIG_STM32_TIM7
CONFIG_STM32_TIM12
CONFIG_STM32_TIM13
CONFIG_STM32_TIM14
CONFIG_STM32_WWDG
CONFIG_STM32_IWDG
CONFIG_STM32_SPI2
CONFIG_STM32_SPI3
CONFIG_STM32_USART2
CONFIG_STM32_USART3
CONFIG_STM32_UART4
CONFIG_STM32_UART5
CONFIG_STM32_I2C1
CONFIG_STM32_I2C2
CONFIG_STM32_I2C3
CONFIG_STM32_CAN1
CONFIG_STM32_CAN2
CONFIG_STM32_DAC1
CONFIG_STM32_DAC2
CONFIG_STM32_PWR -- Required for RTC

APB2
----
CONFIG_STM32_TIM1
CONFIG_STM32_TIM8
CONFIG_STM32_USART1
CONFIG_STM32_USART6
CONFIG_STM32_ADC1
CONFIG_STM32_ADC2
CONFIG_STM32_ADC3
CONFIG_STM32_SDIO
CONFIG_STM32_SPI1
CONFIG_STM32_SYSCFG
CONFIG_STM32_TIM9
CONFIG_STM32_TIM10
CONFIG_STM32_TIM11

Timer devices may be used for different purposes. One special purpose is
to generate modulated outputs for such things as motor control. If CONFIG_STM32_TIMn
is defined (as above) then the following may also be defined to indicate that
the timer is intended to be used for pulsed output modulation, ADC conversion,
or DAC conversion. Note that ADC/DAC require two definition: Not only do you have
to assign the timer (n) for used by the ADC or DAC, but then you also have to
configure which ADC or DAC (m) it is assigned to.

CONFIG_STM32_TIMn_PWM Reserve timer n for use by PWM, n=1,..,14
CONFIG_STM32_TIMn_ADC Reserve timer n for use by ADC, n=1,..,14
CONFIG_STM32_TIMn_ADCm Reserve timer n to trigger ADCm, n=1,..,14, m=1,..,3
CONFIG_STM32_TIMn_DAC Reserve timer n for use by DAC, n=1,..,14
CONFIG_STM32_TIMn_DACm Reserve timer n to trigger DACm, n=1,..,14, m=1,..,2

For each timer that is enabled for PWM usage, we need the following additional
configuration settings:

CONFIG_STM32_TIMx_CHANNEL - Specifies the timer output channel {1,..,4}

NOTE: The STM32 timers are each capable of generating different signals on
each of the four channels with different duty cycles. That capability is
not supported by this driver: Only one output channel per timer.

JTAG Enable settings (by default JTAG-DP and SW-DP are disabled):

CONFIG_STM32_JTAG_FULL_ENABLE - Enables full SWJ (JTAG-DP + SW-DP)
CONFIG_STM32_JTAG_NOJNTRST_ENABLE - Enables full SWJ (JTAG-DP + SW-DP)
but without JNTRST.
CONFIG_STM32_JTAG_SW_ENABLE - Set JTAG-DP disabled and SW-DP enabled

STM3220xxx specific device driver settings

CONFIG_U[S]ARTn_SERIAL_CONSOLE - selects the USARTn (n=1,2,3) or UART
m (m=4,5) for the console and ttys0 (default is the USART1).
CONFIG_U[S]ARTn_RXBUFSIZE - Characters are buffered as received.
This specific the size of the receive buffer
CONFIG_U[S]ARTn_TXBUFSIZE - Characters are buffered before
being sent. This specific the size of the transmit buffer
CONFIG_U[S]ARTn_BAUD - The configure BAUD of the UART. Must be
CONFIG_U[S]ARTn_BITS - The number of bits. Must be either 7 or 8.
CONFIG_U[S]ARTn_PARTIY - 0=no parity, 1=odd parity, 2=even parity
CONFIG_U[S]ARTn_2STOP - Two stop bits

CONFIG_STM32_SPI_INTERRUPTS - Select to enable interrupt driven SPI
support. Non-interrupt-driven, poll-waiting is recommended if the
interrupt rate would be to high in the interrupt driven case.
CONFIG_STM32_SPI_DMA - Use DMA to improve SPI transfer performance.
Cannot be used with CONFIG_STM32_SPI_INTERRUPT.

CONFIG_SDIO_DMA - Support DMA data transfers. Requires CONFIG_STM32_SDIO
and CONFIG_STM32_DMA2.
CONFIG_STM32_SDIO_PRI - Select SDIO interrupt prority. Default: 128
CONFIG_STM32_SDIO_DMAPRIO - Select SDIO DMA interrupt priority.
Default: Medium
CONFIG_STM32_SDIO_WIDTH_D1_ONLY - Select 1-bit transfer mode. Default:
4-bit transfer mode.

CONFIG_STM32_PHYADDR - The 5-bit address of the PHY on the board
CONFIG_STM32_MII - Support Ethernet MII interface
CONFIG_STM32_MII_MCO1 - Use MCO1 to clock the MII interface
CONFIG_STM32_MII_MCO2 - Use MCO2 to clock the MII interface
CONFIG_STM32_RMII - Support Ethernet RMII interface
CONFIG_STM32_AUTONEG - Use PHY autonegotion to determine speed and mode
CONFIG_STM32_ETHFD - If CONFIG_STM32_AUTONEG is not defined, then this
may be defined to select full duplex mode. Default: half-duplex
CONFIG_STM32_ETH100MBPS - If CONFIG_STM32_AUTONEG is not defined, then this
may be defined to select 100 MBps speed. Default: 10 Mbps
CONFIG_STM32_PHYSR - This must be provided if CONFIG_STM32_AUTONEG is
defined. The PHY status register address may diff from PHY to PHY. This
configuration sets the address of the PHY status register.
CONFIG_STM32_PHYSR_SPEED - This must be provided if CONFIG_STM32_AUTONEG is
defined. This provides bit mask indicating 10 or 100MBps speed.
CONFIG_STM32_PHYSR_100MBPS - This must be provided if CONFIG_STM32_AUTONEG is
defined. This provides the value of the speed bit(s) indicating 100MBps speed.
CONFIG_STM32_PHYSR_MODE - This must be provided if CONFIG_STM32_AUTONEG is
defined. This provide bit mask indicating full or half duplex modes.
CONFIG_STM32_PHYSR_FULLDUPLEX - This must be provided if CONFIG_STM32_AUTONEG is
defined. This provides the value of the mode bits indicating full duplex mode.
CONFIG_STM32_ETH_PTP - Precision Time Protocol (PTP). Not supported
but some hooks are indicated with this condition.

STM3220G-EVAL CAN Configuration

CONFIG_CAN - Enables CAN support (one or both of CONFIG_STM32_CAN1 or
CONFIG_STM32_CAN2 must also be defined)
CONFIG_CAN_FIFOSIZE - The size of the circular buffer of CAN messages.
Default: 8
CONFIG_CAN_NPENDINGRTR - The size of the list of pending RTR requests.
Default: 4
CONFIG_CAN_LOOPBACK - A CAN driver may or may not support a loopback
mode for testing. The STM32 CAN driver does support loopback mode.
CONFIG_CAN1_BAUD - CAN1 BAUD rate. Required if CONFIG_STM32_CAN1 is defined.
CONFIG_CAN2_BAUD - CAN1 BAUD rate. Required if CONFIG_STM32_CAN2 is defined.
CONFIG_CAN_TSEG1 - The number of CAN time quanta in segment 1. Default: 6
CONFIG_CAN_TSEG2 - the number of CAN time quanta in segment 2. Default: 7
CONFIG_STM32_CAN_REGDEBUG - If CONFIG_DEBUG_FEATURES is set, this will generate an
dump of all CAN registers.

STM3220G-EVAL LCD Hardware Configuration

STM32 USB OTG FS Host Driver Support

Pre-requisites

CONFIG_USBHOST - Enable general USB host support
CONFIG_STM32_OTGFS - Enable the STM32 USB OTG FS block
CONFIG_STM32_SYSCFG - Needed

Options:

CONFIG_STM32_OTGFS_RXFIFO_SIZE - Size of the RX FIFO in 32-bit words.
Default 128 (512 bytes)
CONFIG_STM32_OTGFS_NPTXFIFO_SIZE - Size of the non-periodic Tx FIFO
in 32-bit words. Default 96 (384 bytes)
CONFIG_STM32_OTGFS_PTXFIFO_SIZE - Size of the periodic Tx FIFO in 32-bit
words. Default 96 (384 bytes)
CONFIG_STM32_OTGFS_DESCSIZE - Maximum size of a descriptor. Default: 128
CONFIG_STM32_OTGFS_SOFINTR - Enable SOF interrupts. Why would you ever
want to do that?
CONFIG_STM32_USBHOST_REGDEBUG - Enable very low-level register access
debug. Depends on CONFIG_DEBUG_FEATURES.
CONFIG_STM32_USBHOST_PKTDUMP - Dump all incoming and outgoing USB
packets. Depends on CONFIG_DEBUG_FEATURES.

Configurations
==============

Each STM3220G-EVAL configuration is maintained in a sub-directory and
can be selected as follow:

cd tools
./configure.sh stm3220g-eval/<subdir>
cd -

Where <subdir> is one of the following:

dhcpd:
-----

This builds the DCHP server using the apps/examples/dhcpd application
(for execution from FLASH.) See apps/examples/README.txt for information
about the dhcpd example.

NOTES:

1. This configuration uses the mconf-based configuration tool. To
change this configurations using that tool, you should:

a. Build and install the kconfig-mconf tool. See nuttx/README.txt
see additional README.txt files in the NuttX tools repository.

b. Execute 'make menuconfig' in nuttx/ in order to start the
reconfiguration process.

2. The server address is 10.0.0.1 and it serves IP addresses in the range
10.0.0.2 through 10.0.0.17 (all of which, of course, are configurable).

3. Default build environment (also easily reconfigured):

CONFIG_HOST_WINDOWS=y
CONFIG_WINDOWS_CYGWIN=y
CONFIG_ARMV7M_TOOLCHAIN_CODESOURCERYW=y

nettest:
-------

This configuration directory may be used to verify networking performance
using the STM32's Ethernet controller. It uses apps/examples/nettest to excercise the
TCP/IP network.

CONFIG_EXAMPLES_NETTEST_SERVER=n : Target is configured as the client
CONFIG_EXAMPLES_NETTEST_PERFORMANCE=y : Only network performance is verified.
CONFIG_EXAMPLES_NETTEST_IPADDR=(10<<24|0<<16|0<<8|2) : Target side is IP: 10.0.0.2
CONFIG_EXAMPLES_NETTEST_DRIPADDR=(10<<24|0<<16|0<<8|1) : Host side is IP: 10.0.0.1
CONFIG_EXAMPLES_NETTEST_CLIENTIP=(10<<24|0<<16|0<<8|1) : Server address used by which ever is client.

NOTES:

1. This configuration uses the mconf-based configuration tool. To
change this configuration using that tool, you should:

a. Build and install the kconfig-mconf tool. See nuttx/README.txt
see additional README.txt files in the NuttX tools repository.

b. Execute 'make menuconfig' in nuttx/ in order to start the
reconfiguration process.

2. Default build environment:

CONFIG_HOST_WINDOWS=y : Windows
CONFIG_WINDOWS_CYGWIN=y : Under Cygwin
CONFIG_ARMV7M_TOOLCHAIN_CODESOURCERYW=y : CodeSourcery under Windows

Than can, of course, be easily changes by reconfiguring per Note 1.

nsh:
---
Configures the NuttShell (nsh) located at apps/examples/nsh. The
Configuration enables both the serial and telnet NSH interfaces.

CONFIG_ARMV7M_TOOLCHAIN_CODESOURCERYW=y : CodeSourcery under Windows
CONFIG_NSH_DHCPC=n : DHCP is disabled
CONFIG_NSH_IPADDR=(192<<24|168<<16|13<<8|161) : Target IP address 192.168.8.161
CONFIG_NSH_DRIPADDR=(192<<24|168<<16|13<<8|1) : Host IP address 192.168.8.1

NOTES:

1. This configuration uses the mconf-based configuration tool. To
change this configurations using that tool, you should:

a. Build and install the kconfig-mconf tool. See nuttx/README.txt
see additional README.txt files in the NuttX tools repository.

b. Execute 'make menuconfig' in nuttx/ in order to start the
reconfiguration process.

2. This example assumes that a network is connected. During its
initialization, it will try to negotiate the link speed. If you have
no network connected when you reset the board, there will be a long
delay (maybe 30 seconds?) before anything happens. That is the timeout
before the networking finally gives up and decides that no network is
available.

3. This example supports the ADC test (apps/examples/adc) but this must
be manually enabled by selecting:

CONFIG_ADC=y : Enable the generic ADC infrastructure
CONFIG_STM32_ADC3=y : Enable ADC3
CONFIG_STM32_TIM1=y : Enable Timer 1
CONFIG_STM32_TIM1_ADC=y : Indicate that timer 1 will be used to trigger an ADC
CONFIG_STM32_TIM1_ADC3=y : Assign timer 1 to drive ADC3 sampling
CONFIG_STM32_ADC3_SAMPLE_FREQUENCY=100 : Select a sampling frequency