README
======
This README discusses issues unique to NuttX configurations for the
STMicro STM32140G-EVAL development board.
Contents
========
- Development Environment
- GNU Toolchain Options
- IDEs
- NuttX buildroot Toolchain
- STM3220G-EVAL-specific Configuration Options
- LEDs
- Ethernet
- PWM
- CAN
- Configurations
Development Environment
=======================
Either Linux or Cygwin on Windows can be used for the development environment.
The source has been built only using the GNU toolchain (see below). Other
toolchains will likely cause problems. Testing was performed using the Cygwin
environment because the Raisonance R-Link emulatator and some RIDE7 development tools
were used and those tools works only under Windows.
GNU Toolchain Options
=====================
The NuttX make system has been modified to support the following different
toolchain options.
1. The CodeSourcery GNU toolchain,
2. The devkitARM GNU toolchain,
3. Raisonance GNU toolchain, or
4. The NuttX buildroot Toolchain (see below).
All testing has been conducted using the CodeSourcery toolchain for Windows. To use
the devkitARM, Raisonance GNU, or NuttX buildroot toolchain, you simply need to
add one of the following configuration options to your .config (or defconfig)
file:
CONFIG_STM32_CODESOURCERYW=y : CodeSourcery under Windows
CONFIG_STM32_CODESOURCERYL=y : CodeSourcery under Linux
CONFIG_STM32_DEVKITARM=y : devkitARM under Windows
CONFIG_STM32_RAISONANCE=y : Raisonance RIDE7 under Windows
CONFIG_STM32_BUILDROOT=y : NuttX buildroot under Linux or Cygwin (default)
If you change the default toolchain, then you may also have to modify the PATH in
the setenv.h file if your make cannot find the tools.
NOTE: the CodeSourcery (for Windows), devkitARM, and Raisonance toolchains are
Windows native toolchains. The CodeSourcey (for Linux) and NuttX buildroot
toolchains are Cygwin and/or Linux native toolchains. There are several limitations
to using a Windows based toolchain in a Cygwin environment. The three biggest are:
1. The Windows toolchain cannot follow Cygwin paths. Path conversions are
performed automatically in the Cygwin makefiles using the 'cygpath' utility
but you might easily find some new path problems. If so, check out 'cygpath -w'
2. Windows toolchains cannot follow Cygwin symbolic links. Many symbolic links
are used in Nuttx (e.g., include/arch). The make system works around these
problems for the Windows tools by copying directories instead of linking them.
But this can also cause some confusion for you: For example, you may edit
a file in a "linked" directory and find that your changes had no effect.
That is because you are building the copy of the file in the "fake" symbolic
directory. If you use a Windows toolchain, you should get in the habit of
making like this:
make clean_context all
An alias in your .bashrc file might make that less painful.
3. Dependencies are not made when using Windows versions of the GCC. This is
because the dependencies are generated using Windows pathes which do not
work with the Cygwin make.
Support has been added for making dependencies with the windows-native toolchains.
That support can be enabled by modifying your Make.defs file as follows:
- MKDEP = $(TOPDIR)/tools/mknulldeps.sh
+ MKDEP = $(TOPDIR)/tools/mkdeps.sh --winpaths "$(TOPDIR)"
If you have problems with the dependency build (for example, if you are not
building on C:), then you may need to modify tools/mkdeps.sh
NOTE 1: The CodeSourcery toolchain (2009q1) does not work with default optimization
level of -Os (See Make.defs). It will work with -O0, -O1, or -O2, but not with
-Os.
NOTE 2: The devkitARM toolchain includes a version of MSYS make. Make sure that
the paths to Cygwin's /bin and /usr/bin directories appear BEFORE the devkitARM
path or will get the wrong version of make.
IDEs
====
NuttX is built using command-line make. It can be used with an IDE, but some
effort will be required to create the project.
Makefile Build
--------------
Under Eclipse, it is pretty easy to set up an "empty makefile project" and
simply use the NuttX makefile to build the system. That is almost for free
under Linux. Under Windows, you will need to set up the "Cygwin GCC" empty
makefile project in order to work with Windows (Google for "Eclipse Cygwin" -
there is a lot of help on the internet).
Native Build
------------
Here are a few tips before you start that effort:
1) Select the toolchain that you will be using in your .config file
2) Start the NuttX build at least one time from the Cygwin command line
before trying to create your project. This is necessary to create
certain auto-generated files and directories that will be needed.
3) Set up include pathes: You will need include/, arch/arm/src/stm32,
arch/arm/src/common, arch/arm/src/armv7-m, and sched/.
4) All assembly files need to have the definition option -D __ASSEMBLY__
on the command line.
Startup files will probably cause you some headaches. The NuttX startup file
is arch/arm/src/stm32/stm32_vectors.S. With RIDE, I have to build NuttX
one time from the Cygwin command line in order to obtain the pre-built
startup object needed by RIDE.
NuttX buildroot Toolchain
=========================
A GNU GCC-based toolchain is assumed. The files */setenv.sh should
be modified to point to the correct path to the Cortex-M3 GCC toolchain (if
different from the default in your PATH variable).
If you have no Cortex-M3 toolchain, one can be downloaded from the NuttX
SourceForge download site (https://sourceforge.net/project/showfiles.php?group_id=189573).
This GNU toolchain builds and executes in the Linux or Cygwin environment.
1. You must have already configured Nuttx in <some-dir>/nuttx.
cd tools
./configure.sh stm3220g-eval/<sub-dir>
2. Download the latest buildroot package into <some-dir>
3. unpack the buildroot tarball. The resulting directory may
have versioning information on it like buildroot-x.y.z. If so,
rename <some-dir>/buildroot-x.y.z to <some-dir>/buildroot.
4. cd <some-dir>/buildroot
5. cp configs/cortexm3-defconfig-4.3.3 .config
6. make oldconfig
7. make
8. Edit setenv.h, if necessary, so that the PATH variable includes
the path to the newly built binaries.
See the file configs/README.txt in the buildroot source tree. That has more
detailed PLUS some special instructions that you will need to follow if you are
building a Cortex-M3 toolchain for Cygwin under Windows.
Ethernet
========
The Ethernet driver is configured to use the MII interface:
Board Jumper Settings:
Jumper Description
JP8 To enable MII, JP8 should not be fitted.
JP6 2-3: Enable MII interface mode
JP5 2-3: Provide 25 MHz clock for MII or 50 MHz clock for RMII by MCO at PA8
SB1 Not used with MII
LEDs
====
The STM3220G-EVAL board has four LEDs labeled LD1, LD2, LD3 and LD4 on the
board.. These LEDs are not used by the board port unless CONFIG_ARCH_LEDS is
defined. In that case, the usage by the board port is defined in
include/board.h and src/up_leds.c. The LEDs are used to encode OS-related\
events as follows:
SYMBOL Meaning LED1* LED2 LED3 LED4
------------------- ----------------------- ------- ------- ------- ------
LED_STARTED NuttX has been started ON OFF OFF OFF
LED_HEAPALLOCATE Heap has been allocated OFF ON OFF OFF
LED_IRQSENABLED Interrupts enabled ON ON OFF OFF
LED_STACKCREATED Idle stack created OFF OFF ON OFF
LED_INIRQ In an interrupt** ON N/C N/C OFF
LED_SIGNAL In a signal handler*** N/C ON N/C OFF
LED_ASSERTION An assertion failed ON ON N/C OFF
LED_PANIC The system has crashed N/C N/C N/C ON
LED_IDLE STM32 is is sleep mode (Optional, not used)
* If LED1, LED2, LED3 are statically on, then NuttX probably failed to boot
and these LEDs will give you some indication of where the failure was
** The normal state is LED3 ON and LED1 faintly glowing. This faint glow
is because of timer interupts that result in the LED being illuminated
on a small proportion of the time.
*** LED2 may also flicker normally if signals are processed.
PWM
===
The STM3220G-Eval has no real on-board PWM devices, but the board can be
configured to output a pulse train using timer output pins. The following
pins have been use to generate PWM output (see board.h for some other
candidates):
TIM4 CH2. Pin PD13 is used by the FSMC (FSMC_A18) and is also connected
to the Motor Control Connector (CN5) just for this purpose. If FSMC is
not enabled, then FSMC_A18 will not be used (and will be tri-stated from
the LCD).
CONFIGURATION:
CONFIG_STM32_TIM4=y
CONFIG_PWM=n
CONFIG_PWM_PULSECOUNT=n
CONFIG_STM32_TIM4_PWM=y
CONFIG_STM32_TIM4_CHANNEL=2
ACCESS:
Daughterboard Extension Connector, CN3, pin 32
Ground is available on CN3, pin1
NOTE: TIM4 hardware will not support pulse counting.
TIM8 CH4: Pin PC9 is used by the microSD card (MicroSDCard_D1) and I2S
(I2S_CKIN) but can be completely disconnected from both by opening JP16.
CONFIGURATION:
CONFIG_STM32_TIM8=y
CONFIG_PWM=n
CONFIG_PWM_PULSECOUNT=y
CONFIG_STM32_TIM8_PWM=y
CONFIG_STM32_TIM8_CHANNEL=4
ACCESS:
Daughterboard Extension Connector, CN3, pin 17
Ground is available on CN3, pin1
CAN
===
Connector 10 (CN10) is DB-9 male connector that can be used with CAN1 or CAN2.
JP10 connects CAN1_RX or CAN2_RX to the CAN transceiver
JP3 connects CAN1_TX or CAN2_TX to the CAN transceiver
CAN signals are then available on CN10 pins:
CN10 Pin 7 = CANH
CN10 Pin 2 = CANL
Mapping to STM32 GPIO pins:
PD0 = FSMC_D2 & CAN1_RX
PD1 = FSMC_D3 & CAN1_TX
PB13 = ULPI_D6 & CAN2_TX
PB5 = ULPI_D7 & CAN2_RX
Configuration Options:
CONFIG_CAN - Enables CAN support (one or both of CONFIG_STM32_CAN1 or
CONFIG_STM32_CAN2 must also be defined)
CONFIG_CAN_EXTID - Enables support for the 29-bit extended ID. Default
Standard 11-bit IDs.
CONFIG_CAN_FIFOSIZE - The size of the circular buffer of CAN messages.
Default: 8
CONFIG_CAN_NPENDINGRTR - The size of the list of pending RTR requests.
Default: 4
CONFIG_STM32_CAN1 - Enable support for CAN1
CONFIG_CAN1_BAUD - CAN1 BAUD rate. Required if CONFIG_STM32_CAN1 is defined.
CONFIG_STM32_CAN2 - Enable support for CAN2
CONFIG_CAN2_BAUD - CAN1 BAUD rate. Required if CONFIG_STM32_CAN2 is defined.
CONFIG_CAN_TSEG1 - The number of CAN time quanta in segment 1. Default: 6
CONFIG_CAN_TSEG2 - the number of CAN time quanta in segment 2. Default: 7
CONFIG_CAN_REGDEBUG - If CONFIG_DEBUG is set, this will generate an
dump of all CAN registers.
STM3220G-EVAL-specific Configuration Options
============================================
CONFIG_ARCH - Identifies the arch/ subdirectory. This should
be set to:
CONFIG_ARCH=arm
CONFIG_ARCH_family - For use in C code:
CONFIG_ARCH_ARM=y
CONFIG_ARCH_architecture - For use in C code:
CONFIG_ARCH_CORTEXM3=y
CONFIG_ARCH_CHIP - Identifies the arch/*/chip subdirectory
CONFIG_ARCH_CHIP=stm32
CONFIG_ARCH_CHIP_name - For use in C code to identify the exact
chip:
CONFIG_ARCH_CHIP_STM32F207IG=y
CONFIG_ARCH_BOARD_STM32_CUSTOM_CLOCKCONFIG - Enables special STM32 clock
configuration features.
CONFIG_ARCH_BOARD_STM32_CUSTOM_CLOCKCONFIG=n
CONFIG_ARCH_BOARD - Identifies the configs subdirectory and
hence, the board that supports the particular chip or SoC.
CONFIG_ARCH_BOARD=stm3220g_eval (for the STM3220G-EVAL development board)
CONFIG_ARCH_BOARD_name - For use in C code
CONFIG_ARCH_BOARD_STM3220G_EVAL=y
CONFIG_ARCH_LOOPSPERMSEC - Must be calibrated for correct operation
of delay loops
CONFIG_ENDIAN_BIG - define if big endian (default is little
endian)
CONFIG_DRAM_SIZE - Describes the installed DRAM (SRAM in this case):
CONFIG_DRAM_SIZE=0x00010000 (64Kb)
CONFIG_DRAM_START - The start address of installed DRAM
CONFIG_DRAM_START=0x20000000
CONFIG_DRAM_END - Last address+1 of installed RAM
CONFIG_DRAM_END=(CONFIG_DRAM_START+CONFIG_DRAM_SIZE)
CONFIG_ARCH_IRQPRIO - The STM3220xxx supports interrupt prioritization
CONFIG_ARCH_IRQPRIO=y
CONFIG_ARCH_LEDS - Use LEDs to show state. Unique to boards that
have LEDs
CONFIG_ARCH_INTERRUPTSTACK - This architecture supports an interrupt
stack. If defined, this symbol is the size of the interrupt
stack in bytes. If not defined, the user task stacks will be
used during interrupt handling.
CONFIG_ARCH_STACKDUMP - Do stack dumps after assertions
CONFIG_ARCH_LEDS - Use LEDs to show state. Unique to board architecture.
CONFIG_ARCH_CALIBRATION - Enables some build in instrumentation that
cause a 100 second delay during boot-up. This 100 second delay
serves no purpose other than it allows you to calibratre
CONFIG_ARCH_LOOPSPERMSEC. You simply use a stop watch to measure
the 100 second delay then adjust CONFIG_ARCH_LOOPSPERMSEC until
the delay actually is 100 seconds.
Individual subsystems can be enabled:
AHB1
----
CONFIG_STM32_CRC
CONFIG_STM32_BKPSRAM
CONFIG_STM32_CCMDATARAM
CONFIG_STM32_DMA1
CONFIG_STM32_DMA2
CONFIG_STM32_ETHMAC
CONFIG_STM32_OTGHS
AHB2
----
CONFIG_STM32_DCMI
CONFIG_STM32_CRYP
CONFIG_STM32_HASH
CONFIG_STM32_RNG
CONFIG_STM32_OTGFS
AHB3
----
CONFIG_STM32_FSMC
APB1
----
CONFIG_STM32_TIM2
CONFIG_STM32_TIM3
CONFIG_STM32_TIM4
CONFIG_STM32_TIM5
CONFIG_STM32_TIM6
CONFIG_STM32_TIM7
CONFIG_STM32_TIM12
CONFIG_STM32_TIM13
CONFIG_STM32_TIM14
CONFIG_STM32_WWDG
CONFIG_STM32_SPI2
CONFIG_STM32_SPI3
CONFIG_STM32_USART2
CONFIG_STM32_USART3
CONFIG_STM32_UART4
CONFIG_STM32_UART5
CONFIG_STM32_I2C1
CONFIG_STM32_I2C2
CONFIG_STM32_I2C3
CONFIG_STM32_CAN1
CONFIG_STM32_CAN2
CONFIG_STM32_DAC1
CONFIG_STM32_DAC2
CONFIG_STM32_PWR -- Required for RTC
APB2
----
CONFIG_STM32_TIM1
CONFIG_STM32_TIM8
CONFIG_STM32_USART1
CONFIG_STM32_USART6
CONFIG_STM32_ADC1
CONFIG_STM32_ADC2
CONFIG_STM32_ADC3
CONFIG_STM32_SDIO
CONFIG_STM32_SPI1
CONFIG_STM32_SYSCFG
CONFIG_STM32_TIM9
CONFIG_STM32_TIM10
CONFIG_STM32_TIM11
Timer and I2C devices may need to the following to force power to be applied
unconditionally at power up. (Otherwise, the device is powered when it is
initialized).
CONFIG_STM32_FORCEPOWER
Timer devices may be used for different purposes. One special purpose is
to generate modulated outputs for such things as motor control. If CONFIG_STM32_TIMn
is defined (as above) then the following may also be defined to indicate that
the timer is intended to be used for pulsed output modulation, ADC conversion,
or DAC conversion. Note that ADC/DAC require two definition: Not only do you have
to assign the timer (n) for used by the ADC or DAC, but then you also have to
configure which ADC or DAC (m) it is assigned to.
CONFIG_STM32_TIMn_PWM Reserve timer n for use by PWM, n=1,..,14
CONFIG_STM32_TIMn_ADC Reserve timer n for use by ADC, n=1,..,14
CONFIG_STM32_TIMn_ADCm Reserve timer n to trigger ADCm, n=1,..,14, m=1,..,3
CONFIG_STM32_TIMn_DAC Reserve timer n for use by DAC, n=1,..,14
CONFIG_STM32_TIMn_DACm Reserve timer n to trigger DACm, n=1,..,14, m=1,..,2
For each timer that is enabled for PWM usage, we need the following additional
configuration settings:
CONFIG_STM32_TIMx_CHANNEL - Specifies the timer output channel {1,..,4}
NOTE: The STM32 timers are each capable of generating different signals on
each of the four channels with different duty cycles. That capability is
not supported by this driver: Only one output channel per timer.
JTAG Enable settings (by default JTAG-DP and SW-DP are disabled):
CONFIG_STM32_JTAG_FULL_ENABLE - Enables full SWJ (JTAG-DP + SW-DP)
CONFIG_STM32_JTAG_NOJNTRST_ENABLE - Enables full SWJ (JTAG-DP + SW-DP)
but without JNTRST.
CONFIG_STM32_JTAG_SW_ENABLE - Set JTAG-DP disabled and SW-DP enabled
STM3220xxx specific device driver settings
CONFIG_U[S]ARTn_SERIAL_CONSOLE - selects the USARTn (n=1,2,3) or UART
m (m=4,5) for the console and ttys0 (default is the USART1).
CONFIG_U[S]ARTn_RXBUFSIZE - Characters are buffered as received.
This specific the size of the receive buffer
CONFIG_U[S]ARTn_TXBUFSIZE - Characters are buffered before
being sent. This specific the size of the transmit buffer
CONFIG_U[S]ARTn_BAUD - The configure BAUD of the UART. Must be
CONFIG_U[S]ARTn_BITS - The number of bits. Must be either 7 or 8.
CONFIG_U[S]ARTn_PARTIY - 0=no parity, 1=odd parity, 2=even parity
CONFIG_U[S]ARTn_2STOP - Two stop bits
CONFIG_STM32_SPI_INTERRUPTS - Select to enable interrupt driven SPI
support. Non-interrupt-driven, poll-waiting is recommended if the
interrupt rate would be to high in the interrupt driven case.
CONFIG_STM32_SPI_DMA - Use DMA to improve SPI transfer performance.
Cannot be used with CONFIG_STM32_SPI_INTERRUPT.
CONFIG_SDIO_DMA - Support DMA data transfers. Requires CONFIG_STM32_SDIO
and CONFIG_STM32_DMA2.
CONFIG_SDIO_PRI - Select SDIO interrupt prority. Default: 128
CONFIG_SDIO_DMAPRIO - Select SDIO DMA interrupt priority.
Default: Medium
CONFIG_SDIO_WIDTH_D1_ONLY - Select 1-bit transfer mode. Default:
4-bit transfer mode.
CONFIG_STM32_PHYADDR - The 5-bit address of the PHY on the board
CONFIG_STM32_MII - Support Ethernet MII interface
CONFIG_STM32_MII_MCO1 - Use MCO1 to clock the MII interface
CONFIG_STM32_MII_MCO2 - Use MCO2 to clock the MII interface
CONFIG_STM32_RMII - Support Ethernet RMII interface
CONFIG_STM32_AUTONEG - Use PHY autonegotion to determine speed and mode
CONFIG_STM32_ETHFD - If CONFIG_STM32_AUTONEG is not defined, then this
may be defined to select full duplex mode. Default: half-duplex
CONFIG_STM32_ETH100MBPS - If CONFIG_STM32_AUTONEG is not defined, then this
may be defined to select 100 MBps speed. Default: 10 Mbps
CONFIG_STM32_PHYSR - This must be provided if CONFIG_STM32_AUTONEG is
defined. The PHY status register address may diff from PHY to PHY. This
configuration sets the address of the PHY status register.
CONFIG_STM32_PHYSR_SPEED - This must be provided if CONFIG_STM32_AUTONEG is
defined. This provides bit mask indicating 10 or 100MBps speed.
CONFIG_STM32_PHYSR_100MBPS - This must be provided if CONFIG_STM32_AUTONEG is
defined. This provides the value of the speed bit(s) indicating 100MBps speed.
CONFIG_STM32_PHYSR_MODE - This must be provided if CONFIG_STM32_AUTONEG is
defined. This provide bit mask indicating full or half duplex modes.
CONFIG_STM32_PHYSR_FULLDUPLEX - This must be provided if CONFIG_STM32_AUTONEG is
defined. This provides the value of the mode bits indicating full duplex mode.
CONFIG_STM32_ETH_PTP - Precision Time Protocol (PTP). Not supported
but some hooks are indicated with this condition.
STM3220G-EVAL CAN Configuration
CONFIG_CAN - Enables CAN support (one or both of CONFIG_STM32_CAN1 or
CONFIG_STM32_CAN2 must also be defined)
CONFIG_CAN_FIFOSIZE - The size of the circular buffer of CAN messages.
Default: 8
CONFIG_CAN_NPENDINGRTR - The size of the list of pending RTR requests.
Default: 4
CONFIG_CAN_LOOPBACK - A CAN driver may or may not support a loopback
mode for testing. The STM32 CAN driver does support loopback mode.
CONFIG_CAN1_BAUD - CAN1 BAUD rate. Required if CONFIG_STM32_CAN1 is defined.
CONFIG_CAN2_BAUD - CAN1 BAUD rate. Required if CONFIG_STM32_CAN2 is defined.
CONFIG_CAN_TSEG1 - The number of CAN time quanta in segment 1. Default: 6
CONFIG_CAN_TSEG2 - the number of CAN time quanta in segment 2. Default: 7
CONFIG_CAN_REGDEBUG - If CONFIG_DEBUG is set, this will generate an
dump of all CAN registers.
STM3220G-EVAL LCD Hardware Configuration
Configurations
==============
Each STM3220G-EVAL configuration is maintained in a sudirectory and
can be selected as follow:
cd tools
./configure.sh stm3220g-eval/<subdir>
cd -
. ./setenv.sh
Where <subdir> is one of the following:
dhcpd:
-----
This builds the DCHP server using the apps/examples/dhcpd application
(for execution from FLASH.) See apps/examples/README.txt for information
about the dhcpd example. The server address is 10.0.0.1 and it serves
IP addresses in the range 10.0.0.2 through 10.0.0.17 (all of which, of
course, are configurable).
CONFIG_STM32_CODESOURCERYW=y : CodeSourcery under Windows
nettest:
-------
This configuration directory may be used to verify networking performance
using the STM32's Ethernet controller. It uses apps/examples/nettest to excercise the
TCP/IP network.
CONFIG_EXAMPLE_NETTEST_SERVER=n : Target is configured as the client
CONFIG_EXAMPLE_NETTEST_PERFORMANCE=y : Only network performance is verified.
CONFIG_EXAMPLE_NETTEST_IPADDR=(10<<24|0<<16|0<<8|2) : Target side is IP: 10.0.0.2
CONFIG_EXAMPLE_NETTEST_DRIPADDR=(10<<24|0<<16|0<<8|1) : Host side is IP: 10.0.0.1
CONFIG_EXAMPLE_NETTEST_CLIENTIP=(10<<24|0<<16|0<<8|1) : Server address used by which ever is client.
nsh:
---
Configures the NuttShell (nsh) located at apps/examples/nsh. The
Configuration enables both the serial and telnet NSH interfaces.
CONFIG_STM32_CODESOURCERYW=y : CodeSourcery under Windows
CONFIG_NSH_DHCPC=n : DHCP is disabled
CONFIG_NSH_IPADDR=(10<<24|0<<16|0<<8|2) : Target IP address 10.0.0.2
CONFIG_NSH_DRIPADDR=(10<<24|0<<16|0<<8|1) : Host IP address 10.0.0.1
NOTES:
1. This example assumes that a network is connected. During its
initialization, it will try to negotiate the link speed. If you have
no network connected when you reset the board, there will be a long
delay (maybe 30 seconds?) before anything happens. That is the timeout
before the networking finally gives up and decides that no network is
available.
2. This example supports the ADC test (apps/examples/adc) but this must
be manually enabled by selecting:
CONFIG_ADC=y : Enable the generic ADC infrastructure
CONFIG_STM32_ADC3=y : Enable ADC3
CONFIG_STM32_TIM1=y : Enable Timer 1
CONFIG_STM32_TIM1_ADC=y : Indicate that timer 1 will be used to trigger an ADC
CONFIG_STM32_TIM1_ADC3=y : Assign timer 1 to drive ADC3 sampling
CONFIG_STM32_ADC3_SAMPLE_FREQUENCY=100 : Select a sampling frequency
See also apps/examples/README.txt
General debug for analog devices (ADC/DAC):
CONFIG_DEBUG_ANALOG
3. This example supports the PWM test (apps/examples/pwm) but this must
be manually enabled by selecting eeither
CONFIG_PWM=y : Enable the generic PWM infrastructure
CONFIG_PWM_PULSECOUNT=n : Disable to support for TIM1/8 pulse counts
CONFIG_STM32_TIM4=y : Enable TIM4
CONFIG_STM32_TIM4_PWM=y : Use TIM4 to generate PWM output
CONFIG_STM32_TIM4_CHANNEL=2 : Select output on TIM4, channel 2
If CONFIG_STM32_FSMC is disabled, output will appear on CN3, pin 32.
Ground is available on CN3, pin1.
Or..
CONFIG_PWM=y : Enable the generic PWM infrastructure
CONFIG_PWM_PULSECOUNT=y : Enable to support for TIM1/8 pulse counts
CONFIG_STM32_TIM8=y : Enable TIM8
CONFIG_STM32_TIM8_PWM=y : Use TIM8 to generate PWM output
CONFIG_STM32_TIM8_CHANNEL=4 : Select output on TIM8, channel 4
If CONFIG_STM32_FSMC is disabled, output will appear on CN3, pin 17
Ground is available on CN23 pin1.
See also include/board.h and apps/examples/README.txt
Special PWM-only debug options:
CONFIG_DEBUG_PWM
4. This example supports the CAN loopback test (apps/examples/can) but this
must be manually enabled by selecting:
CONFIG_CAN=y : Enable the generic CAN infrastructure
CONFIG_CAN_EXID=y or n : Enable to support extended ID frames
CONFIG_STM32_CAN1=y : Enable CAN1
CONFIG_CAN_LOOPBACK=y : Enable CAN loopback mode
See also apps/examples/README.txt
Special CAN-only debug options:
CONFIG_DEBUG_CAN
CONFIG_CAN_REGDEBUG
5. This example can support an FTP client. In order to build in FTP client
support simply uncomment the following lines in the appconfig file (before
configuring) or in the apps/.config file (after configuring):
#CONFIGURED_APPS += netutils/ftpc
#CONFIGURED_APPS += examples/ftpc
6. This example can support an FTP server. In order to build in FTP server
support simply uncomment the following lines in the appconfig file (before
configuring) or in the apps/.config file (after configuring):
#CONFIGURED_APPS += netutils/ftpd
#CONFIGURED_APPS += examples/ftpd
And enable poll() support in the NuttX configuration file:
CONFIG_DISABLE_POLL=n
7. This configuration requires that jumper JP22 be set to enable RS-232 operation.
nsh2:
-----
This is an alternaitve NSH configuration. One limitation of the STM3220G-EVAL
board is that you cannot have both a UART-based NSH console and SDIO support.
The nsh2 differs from the nsh configuration in the following ways:
-CONFIG_STM32_USART3=y : USART3 is disabled
+ CONFIG_STM32_USART3=n
-CONFIG_STM32_SDIO=n : SDIO is enabled
+CONFIG_STM32_SDIO=y
Logically, that is the only difference: This configuration has SDIO (and
the SD card) enabled and the serial console disabled. There is ONLY a
Telnet console!.
There are some special settings to make life with only a Telnet
CONFIG_SYSLOG=y - Enables the System Logging feature.
CONFIG_RAMLOG=y - Enable the RAM-based logging feature.
CONFIG_RAMLOG_CONSOLE=y - Use the RAM logger as the default console.
This means that any console output from non-Telnet threads will
go into the circular buffer in RAM.
CONFIG_RAMLOG_SYSLOG - This enables the RAM-based logger as the
system logger. This means that (1) in addition to the console
output from other tasks, ALL of the debug output will also to
to the circular buffer in RAM, and (2) NSH will now support a
command called 'dmesg' that can be used to dump the RAM log.
There are a few other configuration differences as necessary to support
this different device configuration. Just the do the 'diff' if you are
curious.
NOTES:
1. See the notes for the nsh configuration. Most also apply to the nsh2
configuration.
2. RS-232 is disabled, but Telnet is still available for use as a console.
3. This configuration requires that jumper JP22 be set to enable SDIO operation.
ostest:
------
This configuration directory, performs a simple OS test using
examples/ostest. By default, this project assumes that you are
using the DFU bootloader.
CONFIG_STM32_CODESOURCERYW=y : CodeSourcery under Windows
telnetd:
--------
A simple test of the Telnet daemon(see apps/netutils/README.txt,
apps/examples/README.txt, and apps/examples/telnetd). This is
the same daemon that is used in the nsh configuration so if you
use NSH, then you don't care about this. This test is good for
testing the Telnet daemon only because it works in a simpler
environment than does the nsh configuration.
162473f4c3