OrgApache/incubator-nuttx
OrgApache
/
incubator-nuttx
mirror of https://github.com/apache/incubator-nuttx.git
1
0
Fork 0
Code Issues Releases Wiki Activity
incubator-nuttx/boards/arm/lpc43xx/lpc4357-evb/include/board.h

283 lines
10 KiB
C
Raw Blame History

/****************************************************************************
* boards/arm/lpc43xx/lpc4357-evb/include/board.h
*
* Licensed to the Apache Software Foundation (ASF) under one or more
* contributor license agreements. See the NOTICE file distributed with
* this work for additional information regarding copyright ownership. The
* ASF licenses this file to you under the Apache License, Version 2.0 (the
* "License"); you may not use this file except in compliance with the
* License. You may obtain a copy of the License at
*
* http://www.apache.org/licenses/LICENSE-2.0
*
* Unless required by applicable law or agreed to in writing, software
* distributed under the License is distributed on an "AS IS" BASIS, WITHOUT
* WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. See the
* License for the specific language governing permissions and limitations
* under the License.
*
****************************************************************************/
#ifndef __BOARDS_ARM_LPC43XX_LPC4357_EVB_INCLUDE_BOARD_H
#define __BOARDS_ARM_LPC43XX_LPC4357_EVB_INCLUDE_BOARD_H
/****************************************************************************
* Included Files
****************************************************************************/
#include <nuttx/config.h>
#include <stdbool.h>
#if defined(CONFIG_ARCH_IRQBUTTONS) && defined(CONFIG_LPC43_GPIO_IRQ)
# include <nuttx/irq.h>
#endif
/****************************************************************************
* Pre-processor Definitions
****************************************************************************/
/* Clocking *****************************************************************/
/* NOTE: The following definitions require lpc43_cgu.h. It is not included
* here because the including C file may not have that file in its include
* path.
*
* The Xplorer board has four crystals on board:
*
* Y1 - RTC 32.768 MHz oscillator input,
* Y2 - 24.576 MHz input to the UDA 1380 audio codec,
* Y3 - 12.000 MHz LPC43xx crystal oscillator input
* Y4 - 50 MHz input for Ethernet
*/
#define BOARD_XTAL_FREQUENCY (12000000) /* XTAL oscillator frequency (Y3) */
#define BOARD_RTCCLK_FREQUENCY (32768) /* RTC oscillator frequency (Y1) */
#define BOARD_INTRCOSC_FREQUENCY (4000000) /* Internal RC oscillator frequency */
/* Integer and direct modes are supported:
*
* In integer mode (Fclkout < 156000000):
* Fclkin = BOARD_XTAL_FREQUENCY
* Fclkout = Msel * FClkin / Nsel
* Fcco = 2 * Psel * Fclkout
* In direct mode (Fclkout > 156000000):
* Fclkin = BOARD_XTAL_FREQUENCY
* Fclkout = Msel * FClkin / Nsel
* Fcco = Fclkout
*/
#ifdef CONFIG_LPC43_72MHz
/* NOTE: At 72MHz, the calibrated value of CONFIG_BOARD_LOOPSPERMSEC was
* determined to be:
*
* CONFIG_BOARD_LOOPSPERMSEC=7191
*
* executing from SRAM.
*/
/* Final clocking (Integer mode with no ramp-up)
*
* Fclkout = 6 * 12MHz / 1 = 72MHz
* Fcco = 2 * 2 * 72MHz = 216MHz
*/
# define BOARD_PLL_MSEL (6) /* Msel = 6 */
# define BOARD_PLL_NSEL (1) /* Nsel = 1 */
# define BOARD_PLL_PSEL (2) /* Psel = 2 */
# define BOARD_FCLKOUT_FREQUENCY (72000000) /* 6 * 12,000,000 / 1 */
# define BOARD_FCCO_FREQUENCY (244000000) /* 2 * 2 * Fclkout */
#else
/* NOTE: At 72MHz, the calibrated value of CONFIG_BOARD_LOOPSPERMSEC was
* determined to be:
*
* CONFIG_BOARD_LOOPSPERMSEC=18535
*
* executing from SRAM.
*/
/* Intermediate ramp-up clocking (Integer mode). If BOARD_PLL_RAMP_MSEL
* is not defined, there will be no ramp-up.
*
* Fclkout = 9 * 12MHz / 1 = 108MHz
* Fcco = 2 * 1 * 108MHz = 216MHz
*/
# define BOARD_PLL_RAMP_MSEL (9) /* Msel = 9 */
# define BOARD_PLL_RAMP_NSEL (1) /* Nsel = 1 */
# define BOARD_PLL_RAMP_PSEL (1) /* Psel = 1 */
# define BOARD_RAMP_FCLKOUT (108000000) /* 9 * 12,000,000 / 1 */
# define BOARD_RAMP_FCCO (216000000) /* 2 * 1 * Fclkout */
/* Final clocking (Direct mode).
*
* Fclkout = 17 * 12MHz / 1 = 204MHz
* Fcco = Fclockout = 204MHz
*/
# define BOARD_PLL_MSEL (17) /* Msel = 17 */
# define BOARD_PLL_NSEL (1) /* Nsel = 1 */
# define BOARD_FCLKOUT_FREQUENCY (204000000) /* 17 * 12,000,000 / 1 */
# define BOARD_FCCO_FREQUENCY (204000000) /* Fclockout */
#endif
/* This is the clock setup we configure for:
*
* SYSCLK = BOARD_OSCCLK_FREQUENCY = 12MHz -> Main oscillator for source
* PLL0CLK = (2 * 20 * SYSCLK) / 1 = 480MHz-> multipler=20, pre-divider=1
* CCLCK = 480MHz / 6 = 80MHz -> divider = 6
*/
#define LPC43_CCLK BOARD_FCLKOUT_FREQUENCY
/* USB0 *********************************************************************/
/* Settings needed in lpc43_cpu.c */
#define BOARD_USB0_CLKSRC PLL0USB_CLKSEL_XTAL
#define BOARD_USB0_MDIV 0x06167ffa /* Table 149 datsheet, valid for 12Mhz Fclkin */
#define BOARD_USB0_NP_DIV 0x00302062 /* Table 149 datsheet, valid for 12Mhz Fclkin */
/* SPIFI clocking ***********************************************************/
/* The SPIFI will receive clocking from a divider per the settings provided
* in this file. The NuttX code will configure PLL1 as the input clock
* for the selected divider
*/
#undef BOARD_SPIFI_PLL1 /* No division */
#undef BOARD_SPIFI_DIVA /* Supports division by 1-4 */
#undef BOARD_SPIFI_DIVB /* Supports division by 1-16 */
#undef BOARD_SPIFI_DIVC /* Supports division by 1-16 */
#undef BOARD_SPIFI_DIVD /* Supports division by 1-16 */
#undef BOARD_SPIFI_DIVE /* Supports division by 1-256 */
#if BOARD_FCLKOUT_FREQUENCY < 20000000
# define BOARD_SPIFI_PLL1 1 /* Use PLL1 directly */
#else
# define BOARD_SPIFI_DIVB 1 /* Use IDIVB */
#endif
/* We need to configure the divider so that its output is as close to the
* desired SCLK value. The peak data transfer rate will be about half of
* this frequency in bytes per second.
*/
#if BOARD_FCLKOUT_FREQUENCY < 20000000
# define BOARD_SPIFI_FREQUENCY BOARD_FCLKOUT_FREQUENCY /* 72Mhz? */
#else
# define BOARD_SPIFI_DIVIDER (14) /* 204MHz / 14 = 14.57MHz */
# define BOARD_SPIFI_FREQUENCY (102000000) /* 204MHz / 14 = 14.57MHz */
#endif
/* UART clocking ************************************************************/
/* Configure all U[S]ARTs to use the XTAL input frequency */
#define BOARD_USART0_CLKSRC BASE_USART0_CLKSEL_XTAL
#define BOARD_USART0_BASEFREQ BOARD_XTAL_FREQUENCY
#define BOARD_UART1_CLKSRC BASE_UART1_CLKSEL_XTAL
#define BOARD_UART1_BASEFREQ BOARD_XTAL_FREQUENCY
#define BOARD_USART2_CLKSRC BASE_USART2_CLKSEL_XTAL
#define BOARD_USART2_BASEFREQ BOARD_XTAL_FREQUENCY
#define BOARD_USART3_CLKSRC BASE_USART3_CLKSEL_XTAL
#define BOARD_USART3_BASEFREQ BOARD_XTAL_FREQUENCY
/* Clocking *****************************************************************/
/* The LPC4357-EVB has one user-controllable LED labelled D6 controlled
* by the signal LED_3V3:
*
* ---- ------- -------------
* LED SIGNAL MCU
* ---- ------- -------------
* D6 LED_3V3 PE_7 GPIO7[7]
* ---- ------- -------------
*
* A low output illuminates the LED.
*
* LED index values for use with board_userled()
*/
#define BOARD_LED 0
#define BOARD_NLEDS 1
/* LED bits for use with board_userled_all() */
#define BOARD_LED _BIT (1 << BOARD_LED)
/* If CONFIG_ARCH_LEDS is defined, the LED will be controlled as follows
* for NuttX debug functionality (where NC means "No Change").
*/
/* LED */
#define LED_STARTED 0 /* OFF */
#define LED_HEAPALLOCATE 0 /* OFF */
#define LED_IRQSENABLED 0 /* OFF */
#define LED_STACKCREATED 1 /* ON */
#define LED_INIRQ 2 /* NC */
#define LED_SIGNAL 2 /* NC */
#define LED_ASSERTION 2 /* NC */
#define LED_PANIC 3 /* Flashing */
/* If CONFIG_ARCH_LEDS is not defined, then the LEDs are completely under
* control of the application. The following interfaces are then available
* for application control of the LEDs:
*
* uint32_t board_userled_initialize(void);
* void board_userled(int led, bool ledon);
* void board_userled_all(uint32_t ledset);
*/
/* Button definitions *******************************************************/
/* To be provided */
/* UART Pins ****************************************************************/
/* REVISIT: Thee are most likely left over from the LPC4330-Xplorer */
/* The LPC4357-EVB does not have RS-232 drivers or serial connectors on
* board. USART0 and UART1 are available on J8 as follows:
*
* ------ ------ -----------------------
* SIGNAL J8 PIN LPC4357FET256 PIN
* (TFBGA100 package)
* ------ ------ -----------------------
* U0_TXD pin 9 F6 P6_4 U0_TXD=Alt 2
* U0_RXD pin 10 F9 P6_5 U0_RXD=Alt 2
* U1_TXD pin 13 H8 P1_13 U1_TXD=Alt 1
* U1_RXD pin 14 J8 P1_14 U1_RXD=Alt 1
* ------ ------ -----------------------
*
* The following definitions must be provided so that the LPC43 serial
* driver can set up the U[S]ART for the serial console properly (see the
* file arch/arc/src/lpc43xx/lpc4310203050_pinconf.h for more info).
*/
#define PINCONF_U0_TXD PINCONF_U0_TXD_4
#define PINCONF_U0_RXD PINCONF_U0_RXD_4
#define PINCONF_U0_DIR PINCONF_U0_DIR_3
#define PINCONF_U1_TXD PINCONF_U1_TXD_1
#define PINCONF_U1_RXD PINCONF_U1_RXD_1
#define PINCONF_U2_TXD PINCONF_U2_TXD_3
#define PINCONF_U2_RXD PINCONF_U2_RXD_3
#define PINCONF_U2_DIR PINCONF_U2_DIR_2
#define PINCONF_U3_TXD PINCONF_U3_TXD_4
#define PINCONF_U3_RXD PINCONF_U3_RXD_4
#define PINCONF_U3_DIR PINCONF_U3_DIR_3
#endif /* __BOARDS_ARM_LPC43XX_LPC4357_EVB_INCLUDE_BOARD_H */
Reference in New Issue View Git Blame Copy Permalink