154 lines
4.9 KiB
Plaintext
154 lines
4.9 KiB
Plaintext
README
|
|
======
|
|
|
|
This directory holds the port to the NXP S32K118EVB-Q064 development board.
|
|
|
|
Contents
|
|
========
|
|
|
|
o Status
|
|
o Serial Console
|
|
o LEDs and Buttons
|
|
o OpenSDA Notes
|
|
o Configurations
|
|
|
|
Status
|
|
======
|
|
|
|
2019-08-14: Configuration created but entirely untested.
|
|
|
|
2019-08-17: The port is code complete. It compiles with no errors or
|
|
warnings but is untested. Still waiting for hardware.
|
|
|
|
2019-08-20: The very first image that I wrote to FLASH seems to have
|
|
"bricked" the board. The board is sensitive to (1) resetting into a bad
|
|
state and (2) incorrect flash configurations. It is difficult to
|
|
impossible to recover from these start-up errors.
|
|
|
|
2019-08-22: My S32K118EVB is still borked, but after some additional
|
|
changes, Fabio Balzano has verified that the NSH is functional on that
|
|
board.
|
|
|
|
2019-10-19: The aforementioned fixes for the FLASH issues were converted
|
|
into a set of FLASH configuration options, with a proven default state.
|
|
|
|
2020-06-15: Added FlexCAN driver with SocketCAN support to the S32K1XX
|
|
arch. Might work on the S32K118EVB as well, but remains untested.
|
|
|
|
2020-06-16: Added Emulated EEPROM driver and initialization.
|
|
|
|
TODO: Need to calibrate the delay loop. The current value of
|
|
CONFIG_BOARD_LOOPSPERMSEC is a bogus value retained from a copy-paste
|
|
(see apps/examples/calib_udelay).
|
|
|
|
Serial Console
|
|
==============
|
|
|
|
By default, the serial console will be provided on the OpenSDA VCOM port:
|
|
|
|
OpenSDA UART RX PTB0 (LPUART0_RX)
|
|
OpenSDA UART TX PTB1 (LPUART0_TX)
|
|
|
|
USB drivers for the PEmicro CDC Serial Port are available here:
|
|
http://www.pemicro.com/opensda/
|
|
|
|
LEDs and Buttons
|
|
================
|
|
|
|
LEDs
|
|
----
|
|
The S32K118EVB has one RGB LED:
|
|
|
|
RedLED PTD16 (FTM0 CH1)
|
|
GreenLED PTD15 (FTM0 CH0)
|
|
BlueLED PTE8 (FTM0 CH6)
|
|
|
|
An output of '1' illuminates the LED.
|
|
|
|
If CONFIG_ARCH_LEDS is not defined, then the user can control the LEDs in
|
|
any way. The following definitions are used to access individual RGB
|
|
components (see s32k118evb.h):
|
|
|
|
GPIO_LED_R
|
|
GPIO_LED_G
|
|
GPIO_LED_B
|
|
|
|
The RGB components could, alternatively, be controlled through PWM using
|
|
the common RGB LED driver.
|
|
|
|
If CONFIG_ARCH_LEDs is defined, then NuttX will control the LEDs on board
|
|
the S32K118EVB. The following definitions describe how NuttX controls the
|
|
LEDs:
|
|
|
|
==========================================+========+========+=========
|
|
RED GREEN BLUE
|
|
==========================================+========+========+=========
|
|
|
|
LED_STARTED NuttX has been started OFF OFF OFF
|
|
LED_HEAPALLOCATE Heap has been allocated OFF OFF ON
|
|
LED_IRQSENABLED Interrupts enabled OFF OFF ON
|
|
LED_STACKCREATED Idle stack created OFF ON OFF
|
|
LED_INIRQ In an interrupt (no change)
|
|
LED_SIGNAL In a signal handler (no change)
|
|
LED_ASSERTION An assertion failed (no change)
|
|
LED_PANIC The system has crashed FLASH OFF OFF
|
|
LED_IDLE S32K118 in sleep mode (no change)
|
|
==========================================+========+========+=========
|
|
|
|
Buttons
|
|
-------
|
|
The S32K118EVB supports two buttons:
|
|
|
|
SW2 PTD3
|
|
SW3 PTD5
|
|
|
|
OpenSDA Notes
|
|
=============
|
|
|
|
- USB drivers for the PEmicro CDC Serial Port are available here:
|
|
http://www.pemicro.com/opensda/
|
|
|
|
- The drag'n'drog interface expects files in .srec format.
|
|
|
|
- Using Segger J-Link: Easy... but remember to use the SWD connector J14
|
|
near the touch electrodes and not the OpenSDA connector near the OpenSDA
|
|
USB connector J7.
|
|
|
|
Configurations
|
|
==============
|
|
|
|
Common Information
|
|
------------------
|
|
Each S32K118EVB configuration is maintained in a sub-directory and can be
|
|
selected as follows:
|
|
|
|
tools/configure.sh s32k118evb:<subdir>
|
|
|
|
Where <subdir> is one of the sub-directories listed in the next paragraph.
|
|
|
|
NOTES (common for all configurations):
|
|
|
|
1. This configuration uses the mconf-based configuration tool. To change
|
|
this configuration using that tool, you should:
|
|
|
|
a. Build and install the kconfig-mconf tool. See nuttx/README.txt.
|
|
Also see additional README.txt files in the NuttX tools repository.
|
|
|
|
b. Execute 'make menuconfig' in nuttx/ in order to start the
|
|
reconfiguration process.
|
|
|
|
2. Unless otherwise stated, the serial console used is LPUART0 at
|
|
115,200 8N1. This corresponds to the OpenSDA VCOM port.
|
|
|
|
Configuration Sub-directories
|
|
-----------------------------
|
|
|
|
nsh:
|
|
---
|
|
Configures the NuttShell (nsh) located at apps/examples/nsh. Support
|
|
for builtin applications is enabled, but in the base configuration no
|
|
builtin applications are selected.
|
|
|
|
NOTE: This is a very minimal NSH configuration in order to reduce
|
|
memory usage. Most of the NSH niceties are not available.
|