OrgApache/incubator-nuttx
OrgApache
/
incubator-nuttx
mirror of https://github.com/apache/incubator-nuttx.git
1
0
Fork 0
Code Issues Releases Wiki Activity
incubator-nuttx/drivers/lcd/jd9851.c

917 lines
28 KiB
C
Raw Blame History

/****************************************************************************
* drivers/lcd/jd9851.c
*
* Licensed to the Apache Software Foundation (ASF) under one or more
* contributor license agreements. See the NOTICE file distributed with
* this work for additional information regarding copyright ownership. The
* ASF licenses this file to you under the Apache License, Version 2.0 (the
* "License"); you may not use this file except in compliance with the
* License. You may obtain a copy of the License at
*
* http://www.apache.org/licenses/LICENSE-2.0
*
* Unless required by applicable law or agreed to in writing, software
* distributed under the License is distributed on an "AS IS" BASIS, WITHOUT
* WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. See the
* License for the specific language governing permissions and limitations
* under the License.
*
****************************************************************************/
/****************************************************************************
* Included Files
****************************************************************************/
#include <nuttx/config.h>
#include <sys/types.h>
#include <stdint.h>
#include <stdbool.h>
#include <string.h>
#include <assert.h>
#include <errno.h>
#include <debug.h>
#include <nuttx/arch.h>
#include <nuttx/spi/spi.h>
#include <nuttx/lcd/lcd.h>
#include <nuttx/lcd/jd9851.h>
#include "jd9851.h"
#ifdef CONFIG_LCD_JD9851
/****************************************************************************
* Pre-processor Definitions
****************************************************************************/
/* Verify that all configuration requirements have been met */
#ifndef CONFIG_LCD_JD9851_SPIMODE
# define CONFIG_LCD_JD9851_SPIMODE SPIDEV_MODE0
#endif
/* SPI frequency */
#ifndef CONFIG_LCD_JD9851_FREQUENCY
# define CONFIG_LCD_JD9851_FREQUENCY 1000000
#endif
/* Check contrast selection */
#if !defined(CONFIG_LCD_MAXCONTRAST)
# define CONFIG_LCD_MAXCONTRAST 1
#endif
/* Check power setting */
#if !defined(CONFIG_LCD_MAXPOWER) || CONFIG_LCD_MAXPOWER < 1
# define CONFIG_LCD_MAXPOWER 1
#endif
#if CONFIG_LCD_MAXPOWER > 255
# error "CONFIG_LCD_MAXPOWER must be less than 256 to fit in uint8_t"
#endif
/* Check orientation */
#if defined(CONFIG_LCD_PORTRAIT)
# if defined(CONFIG_LCD_LANDSCAPE) || defined(CONFIG_LCD_RLANDSCAPE) ||\
defined(CONFIG_LCD_RPORTRAIT)
# error "Cannot define both portrait and any other orientations"
# endif
#elif defined(CONFIG_LCD_RPORTRAIT)
# if defined(CONFIG_LCD_LANDSCAPE) || defined(CONFIG_LCD_RLANDSCAPE)
# error "Cannot define both rportrait and any other orientations"
# endif
#elif defined(CONFIG_LCD_LANDSCAPE)
# ifdef CONFIG_LCD_RLANDSCAPE
# error "Cannot define both landscape and any other orientations"
# endif
#elif !defined(CONFIG_LCD_RLANDSCAPE)
# define CONFIG_LCD_LANDSCAPE 1
#endif
/* Display Resolution */
#if !defined(CONFIG_LCD_JD9851_XRES)
# define CONFIG_LCD_JD9851_XRES 240
#endif
#if !defined(CONFIG_LCD_JD9851_YRES)
# define CONFIG_LCD_JD9851_YRES 320
#endif
#if !defined(CONFIG_LCD_JD9851_BPP)
# define CONFIG_LCD_JD9851_BPP 16
#endif
#if !defined(CONFIG_LCD_JD9851_XOFFSET)
# define CONFIG_LCD_JD9851_XOFFSET 0
#endif
#if !defined(CONFIG_LCD_JD9851_YOFFSET)
# define CONFIG_LCD_JD9851_YOFFSET 0
#endif
#define JD9851_LUT_SIZE CONFIG_LCD_JD9851_YRES
#if defined(CONFIG_LCD_LANDSCAPE) || defined(CONFIG_LCD_RLANDSCAPE)
# define JD9851_XRES CONFIG_LCD_JD9851_YRES
# define JD9851_YRES CONFIG_LCD_JD9851_XRES
# define JD9851_XOFFSET CONFIG_LCD_JD9851_YOFFSET
# define JD9851_YOFFSET CONFIG_LCD_JD9851_XOFFSET
#else
# define JD9851_XRES CONFIG_LCD_JD9851_XRES
# define JD9851_YRES CONFIG_LCD_JD9851_YRES
# define JD9851_XOFFSET CONFIG_LCD_JD9851_XOFFSET
# define JD9851_YOFFSET CONFIG_LCD_JD9851_YOFFSET
#endif
/* Color depth and format */
#ifdef CONFIG_LCD_JD9851_BPP
# if (CONFIG_LCD_JD9851_BPP == 16)
# define JD9851_BPP 16
# define JD9851_COLORFMT FB_FMT_RGB16_565
# define JD9851_BYTESPP 2
# else
# define JD9851_BPP 16
# define JD9851_COLORFMT FB_FMT_RGB16_565
# define JD9851_BYTESPP 2
# warning "Invalid color depth. Falling back to 16bpp"
# endif
#endif
/****************************************************************************
* Private Types
****************************************************************************/
/* This structure describes the state of this driver */
struct jd9851_dev_s
{
/* Publicly visible device structure */
struct lcd_dev_s dev;
/* Private LCD-specific information follows */
FAR struct spi_dev_s *spi; /* SPI device */
uint8_t bpp; /* Selected color depth */
uint8_t power; /* Current power setting */
/* This is working memory allocated by the LCD driver for each LCD device
* and for each color plane. This memory will hold one raster line of data.
* The size of the allocated run buffer must therefore be at least
* (bpp * xres / 8). Actual alignment of the buffer must conform to the
* bitwidth of the underlying pixel type.
*
* If there are multiple planes, they may share the same working buffer
* because different planes will not be operate on concurrently. However,
* if there are multiple LCD devices, they must each have unique run
* buffers.
*/
uint16_t runbuffer[JD9851_LUT_SIZE];
};
/****************************************************************************
* Private Function Protototypes
****************************************************************************/
/* Misc. Helpers */
static void jd9851_select(FAR struct spi_dev_s *spi, int bits);
static void jd9851_deselect(FAR struct spi_dev_s *spi);
static inline void jd9851_sendcmd(FAR struct jd9851_dev_s *dev, uint8_t cmd);
static void jd9851_cmddata(FAR struct jd9851_dev_s *dev, uint8_t cmd,
const uint8_t *data, int len);
static void jd9851_init(FAR struct jd9851_dev_s *dev);
static void jd9851_sleep(FAR struct jd9851_dev_s *dev, bool sleep);
static void jd9851_setorientation(FAR struct jd9851_dev_s *dev);
static void jd9851_display(FAR struct jd9851_dev_s *dev, bool on);
static void jd9851_setcursor(FAR struct jd9851_dev_s *dev,
uint16_t x0, uint16_t y0,
uint16_t x1, uint16_t y1);
static void jd9851_bpp(FAR struct jd9851_dev_s *dev, int bpp);
static void jd9851_wrram(FAR struct jd9851_dev_s *dev,
FAR const uint8_t *buff, size_t size , size_t skip,
size_t count);
#ifndef CONFIG_LCD_NOGETRUN
static void jd9851_rdram(FAR struct jd9851_dev_s *dev,
FAR uint16_t *buff, size_t size);
#endif
static void jd9851_fill(FAR struct jd9851_dev_s *dev, uint16_t color);
/* LCD Data Transfer Methods */
static int jd9851_putrun(FAR struct lcd_dev_s *dev,
fb_coord_t row, fb_coord_t col,
FAR const uint8_t *buffer, size_t npixels);
static int jd9851_putarea(FAR struct lcd_dev_s *dev,
fb_coord_t row_start, fb_coord_t row_end,
fb_coord_t col_start, fb_coord_t col_end,
FAR const uint8_t *buffer, fb_coord_t stride);
#ifndef CONFIG_LCD_NOGETRUN
static int jd9851_getrun(FAR struct lcd_dev_s *dev,
fb_coord_t row, fb_coord_t col,
FAR uint8_t *buffer, size_t npixels);
#endif
/* LCD Configuration */
static int jd9851_getvideoinfo(FAR struct lcd_dev_s *dev,
FAR struct fb_videoinfo_s *vinfo);
static int jd9851_getplaneinfo(FAR struct lcd_dev_s *dev,
unsigned int planeno,
FAR struct lcd_planeinfo_s *pinfo);
/* LCD Specific Controls */
static int jd9851_getpower(FAR struct lcd_dev_s *dev);
static int jd9851_setpower(FAR struct lcd_dev_s *dev, int power);
static int jd9851_getcontrast(FAR struct lcd_dev_s *dev);
static int jd9851_setcontrast(FAR struct lcd_dev_s *dev,
unsigned int contrast);
/****************************************************************************
* Private Data
****************************************************************************/
static struct jd9851_dev_s g_lcddev;
/****************************************************************************
* Private Functions
****************************************************************************/
/****************************************************************************
* Name: jd9851_select
*
* Description:
* Select the SPI, locking and re-configuring if necessary
*
* Input Parameters:
* spi - Reference to the SPI driver structure
* bits - Number of SPI bits
*
* Returned Value:
* None
*
* Assumptions:
*
****************************************************************************/
static void jd9851_select(FAR struct spi_dev_s *spi, int bits)
{
/* Select JD9851 chip (locking the SPI bus in case there are multiple
* devices competing for the SPI bus
*/
SPI_LOCK(spi, true);
SPI_SELECT(spi, SPIDEV_DISPLAY(0), true);
/* Now make sure that the SPI bus is configured for the JD9851 (it
* might have gotten configured for a different device while unlocked)
*/
SPI_SETMODE(spi, CONFIG_LCD_JD9851_SPIMODE);
SPI_SETBITS(spi, bits);
SPI_SETFREQUENCY(spi, CONFIG_LCD_JD9851_FREQUENCY);
}
/****************************************************************************
* Name: jd9851_deselect
*
* Description:
* De-select the SPI
*
* Input Parameters:
* spi - Reference to the SPI driver structure
*
* Returned Value:
* None
*
* Assumptions:
*
****************************************************************************/
static void jd9851_deselect(FAR struct spi_dev_s *spi)
{
/* De-select JD9851 chip and relinquish the SPI bus. */
SPI_SELECT(spi, SPIDEV_DISPLAY(0), false);
SPI_LOCK(spi, false);
}
/****************************************************************************
* Name: jd9851_sendcmd
*
* Description:
* Send a command to the driver.
*
****************************************************************************/
static inline void jd9851_sendcmd(FAR struct jd9851_dev_s *dev, uint8_t cmd)
{
jd9851_select(dev->spi, 8);
SPI_CMDDATA(dev->spi, SPIDEV_DISPLAY(0), true);
SPI_SEND(dev->spi, cmd);
SPI_CMDDATA(dev->spi, SPIDEV_DISPLAY(0), false);
jd9851_deselect(dev->spi);
}
/****************************************************************************
* Name: jd9851_cmddata
*
* Description:
* Send a command and a series of data to the driver.
*
****************************************************************************/
static void jd9851_cmddata(FAR struct jd9851_dev_s *dev, uint8_t cmd,
const uint8_t *data, int len)
{
jd9851_select(dev->spi, 8);
SPI_CMDDATA(dev->spi, SPIDEV_DISPLAY(0), true);
SPI_SEND(dev->spi, cmd);
SPI_CMDDATA(dev->spi, SPIDEV_DISPLAY(0), false);
SPI_SNDBLOCK(dev->spi, data, len);
jd9851_deselect(dev->spi);
}
/****************************************************************************
* Name: jd9851_init
*
* Description:
* Send jd9851 internal init commands.
*
* Assumption/Limitations:
* Initialization is hardware-specific and may need to be rewritten for
* different modules.
*
****************************************************************************/
static void jd9851_init(FAR struct jd9851_dev_s *dev)
{
jd9851_cmddata(dev, JD9851_PASSWORD, (const uint8_t *) "\x98\x51\xe9", 3);
jd9851_cmddata(dev, JD9851_SET_PAGE_CMD, (const uint8_t *) "\x00", 1);
jd9851_cmddata(dev, JD9851_GAMMA_SET_CMD, (const uint8_t *)
"\x1b\x7a\x17\x32", 4);
jd9851_cmddata(dev, JD9851_R_GAMMA_SET_CMD, (const uint8_t *)
"\x3c\x32\x2b\x2c\x2f\x32\x2c\x2b\x28\x27\x22\x16\x10\x0b\
\x05\x0e\x3c\x32\x2b\x2c\x2f\x32\x2c\x2b\x28\x27\x22\x16\
\x10\x0b\x05\x0e", 32);
jd9851_cmddata(dev, JD9851_POWER_CTRL, (const uint8_t *)
"\x33\x28\xcc", 3);
jd9851_cmddata(dev, JD9851_DCDC_SET, (const uint8_t *)
"\x47\x7a\x30\x30\x6c\x60\x50\x70", 8);
jd9851_cmddata(dev, JD9851_VDDD_CTRL, (const uint8_t *) "\x38\x3c", 2);
jd9851_cmddata(dev, JD9851_SETSTBA, (const uint8_t *) "\x31\x20", 2);
jd9851_cmddata(dev, JD9851_SETPANEL, (const uint8_t *) "\x16", 1);
jd9851_cmddata(dev, JD9851_SETRGBCYC, (const uint8_t *)
"\x08\x00\x0a\x10\x08\x54\x45\x71\x2c", 9);
jd9851_cmddata(dev, JD9851_SETTCON, (const uint8_t *)
"\x00\xa0\x79\x0e\x0a\x16\x79\x0e\x0a\x16\x79\x0e\x0a\x16\
\x82\x00\x03", 17);
jd9851_cmddata(dev, JD9851_SETGD, (const uint8_t *)
"\x04\x0c\x6b\x0f\x07\x03", 6);
jd9851_cmddata(dev, JD9851_SETRGBIF, (const uint8_t *) "\x22\x20", 2);
jd9851_cmddata(dev, JD9851_RAM_CTRL, (const uint8_t *) "\x00\x00", 2);
jd9851_cmddata(dev, JD9851_SET_PAGE_CMD, (const uint8_t *) "\x02", 1);
jd9851_cmddata(dev, JD9851_DCDC_SET2, (const uint8_t *)
"\x19\xa0\x2f\x04\x33", 5);
jd9851_cmddata(dev, JD9851_SETPANEL, (const uint8_t *)
"\x10\x66\x66\x01", 4);
jd9851_cmddata(dev, JD9851_OSCM_SET, (const uint8_t *) "\x01\x00\x00", 3);
jd9851_cmddata(dev, JD9851_SETMIPI_2, (const uint8_t *) "\x10\x20\xf4", 3);
jd9851_sendcmd(dev, JD9851_SLEEP_OUT);
up_mdelay(120);
}
/****************************************************************************
* Name: jd9851_sleep
*
* Description:
* Sleep or wake up the driver.
*
****************************************************************************/
static void jd9851_sleep(FAR struct jd9851_dev_s *dev, bool sleep)
{
if (sleep)
{
jd9851_sendcmd(dev, JD9851_SLEEP_IN);
}
else
{
jd9851_sendcmd(dev, JD9851_SLEEP_OUT);
}
up_mdelay(120);
}
/****************************************************************************
* Name: jd9851_display
*
* Description:
* Turn on or off the display.
*
****************************************************************************/
static void jd9851_display(FAR struct jd9851_dev_s *dev, bool on)
{
uint8_t reg;
#if defined(CONFIG_LCD_JD9851_TE)
reg = JD9851_TE_MODE0;
jd9851_cmddata(dev, JD9851_TEON, &reg, 1);
#endif
#if defined(CONFIG_LCD_JD9851_INVERT)
jd9851_sendcmd(dev, JD9851_INVERSION_ON);
#endif
if (on)
{
jd9851_sendcmd(dev, JD9851_DISON);
}
else
{
jd9851_sendcmd(dev, JD9851_DISOFF);
}
}
/****************************************************************************
* Name: jd9851_setorientation
*
* Description:
* Set screen orientation.
*
****************************************************************************/
static void jd9851_setorientation(FAR struct jd9851_dev_s *dev)
{
uint8_t reg = 0x00;
#if !defined(CONFIG_LCD_PORTRAIT) || defined(CONFIG_LCD_JD9851_BGR)
# if defined(CONFIG_LCD_RLANDSCAPE)
reg = JD9851_MADCTL_MY | JD9851_MADCTL_MV;
# elif defined(CONFIG_LCD_LANDSCAPE)
reg = JD9851_MADCTL_MV | JD9851_MADCTL_MX;
# elif defined(CONFIG_LCD_RPORTRAIT)
reg = JD9851_MADCTL_MY | JD9851_MADCTL_MX;
# endif
# if defined(CONFIG_LCD_JD9851_BGR)
reg |= JD9851_MADCTL_BGR;
# endif
#endif
jd9851_cmddata(dev, JD9851_MADCTL, &reg, 1);
}
/****************************************************************************
* Name: jd9851_setcursor
*
* Description:
* Set the rectangular area for an upcoming read or write from RAM.
*
****************************************************************************/
static void jd9851_setcursor(FAR struct jd9851_dev_s *dev,
uint16_t x0, uint16_t y0,
uint16_t x1, uint16_t y1)
{
/* Set row address */
jd9851_sendcmd(dev, JD9851_PASET);
jd9851_select(dev->spi, 8);
SPI_SEND(dev->spi, (y0 + JD9851_YOFFSET) >> 8);
SPI_SEND(dev->spi, (y0 + JD9851_YOFFSET) & 0xff);
SPI_SEND(dev->spi, (y1 + JD9851_YOFFSET) >> 8);
SPI_SEND(dev->spi, (y1 + JD9851_YOFFSET) & 0xff);
jd9851_deselect(dev->spi);
/* Set column address */
jd9851_sendcmd(dev, JD9851_CASET);
jd9851_select(dev->spi, 8);
SPI_SEND(dev->spi, (x0 + JD9851_XOFFSET) >> 8);
SPI_SEND(dev->spi, (x0 + JD9851_XOFFSET) & 0xff);
SPI_SEND(dev->spi, (x1 + JD9851_XOFFSET) >> 8);
SPI_SEND(dev->spi, (x1 + JD9851_XOFFSET) & 0xff);
jd9851_deselect(dev->spi);
}
/****************************************************************************
* Name: jd9851_bpp
*
* Description:
* Set the color depth of the device.
*
****************************************************************************/
static void jd9851_bpp(FAR struct jd9851_dev_s *dev, int bpp)
{
uint8_t depth;
/* Don't send any command if the depth hasn't changed. */
if (dev->bpp != bpp)
{
depth = bpp >> 2 | 1;
depth = (depth & 0x0f) << 4 | depth;
jd9851_cmddata(dev, JD9851_COLMOD, &depth, 1);
/* Cache the new BPP */
dev->bpp = bpp;
}
}
/****************************************************************************
* Name: jd9851_wrram
*
* Description:
* Write to the driver's RAM. It is possible to write multiples of size
* while skipping some values.
*
****************************************************************************/
static void jd9851_wrram(FAR struct jd9851_dev_s *dev,
FAR const uint8_t *buff, size_t size, size_t skip,
size_t count)
{
size_t i;
jd9851_sendcmd(dev, JD9851_RAMWR);
jd9851_select(dev->spi, 8);
for (i = 0; i < count; i++)
{
SPI_SNDBLOCK(dev->spi, buff + (i * (size + skip)), size);
}
jd9851_deselect(dev->spi);
}
/****************************************************************************
* Name: jd9851_rdram
*
* Description:
* Read from the driver's RAM.
*
****************************************************************************/
#ifndef CONFIG_LCD_NOGETRUN
static void jd9851_rdram(FAR struct jd9851_dev_s *dev,
FAR uint16_t *buff, size_t size)
{
jd9851_sendcmd(dev, JD9851_RAMRD);
jd9851_select(dev->spi, JD9851_BYTESPP * 8);
SPI_RECVBLOCK(dev->spi, buff, size);
jd9851_deselect(dev->spi);
}
#endif
/****************************************************************************
* Name: jd9851_fill
*
* Description:
* Fill the display with the specified color.
*
****************************************************************************/
static void jd9851_fill(FAR struct jd9851_dev_s *dev, uint16_t color)
{
int i;
jd9851_setcursor(dev, 0, 0, JD9851_XRES - 1, JD9851_YRES - 1);
jd9851_sendcmd(dev, JD9851_RAMWR);
jd9851_select(dev->spi, JD9851_BYTESPP *8);
for (i = 0; i < JD9851_XRES * JD9851_YRES; i++)
{
SPI_SEND(dev->spi, color);
}
jd9851_deselect(dev->spi);
}
/****************************************************************************
* Name: jd9851_putrun
*
* Description:
* This method can be used to write a partial raster line to the LCD:
*
* dev - The lcd device
* row - Starting row to write to (range: 0 <= row < yres)
* col - Starting column to write to (range: 0 <= col <= xres-npixels)
* buffer - The buffer containing the run to be written to the LCD
* npixels - The number of pixels to write to the LCD
* (range: 0 < npixels <= xres-col)
*
****************************************************************************/
static int jd9851_putrun(FAR struct lcd_dev_s *dev,
fb_coord_t row, fb_coord_t col,
FAR const uint8_t *buffer, size_t npixels)
{
FAR struct jd9851_dev_s *priv = (FAR struct jd9851_dev_s *)dev;
ginfo("row: %d col: %d npixels: %d\n", row, col, npixels);
DEBUGASSERT(buffer && ((uintptr_t)buffer & 1) == 0);
jd9851_setcursor(priv, col, row, col + npixels - 1, row);
jd9851_wrram(priv, buffer, npixels * (priv->bpp >> 3), 0, 1);
return OK;
}
/****************************************************************************
* Name: jd9851_putarea
*
* Description:
* This method can be used to write a partial area to the LCD:
*
* dev - The lcd device
* row_start - Starting row to write to (range: 0 <= row < yres)
* row_end - Ending row to write to (range: row_start <= row < yres)
* col_start - Starting column to write to (range: 0 <= col <= xres)
* col_end - Ending column to write to
* (range: col_start <= col_end < xres)
* buffer - The buffer containing the area to be written to the LCD
* stride - Length of a line in bytes. This parameter may be necessary
* to allow the LCD driver to calculate the offset for partial
* writes when the buffer needs to be splited for row-by-row
* writing.
*
****************************************************************************/
static int jd9851_putarea(FAR struct lcd_dev_s *dev,
fb_coord_t row_start, fb_coord_t row_end,
fb_coord_t col_start, fb_coord_t col_end,
FAR const uint8_t *buffer, fb_coord_t stride)
{
FAR struct jd9851_dev_s *priv = (FAR struct jd9851_dev_s *)dev;
size_t cols = col_end - col_start + 1;
size_t rows = row_end - row_start + 1;
size_t row_size = cols * (priv->bpp >> 3);
ginfo("row_start: %d row_end: %d col_start: %d col_end: %d\n",
row_start, row_end, col_start, col_end);
DEBUGASSERT(buffer && ((uintptr_t)buffer & 1) == 0);
jd9851_setcursor(priv, col_start, row_start, col_end, row_end);
/* If the stride is the same of the row, a single SPI transfer is enough.
* That is always true for lcddev. For framebuffer, that indicates a full
* screen or full row update.
*/
if (stride == row_size)
{
/* simpler case, we can just send the whole buffer */
ginfo("Using full screen/full row mode\n");
jd9851_wrram(priv, buffer, rows * row_size, 0, 1);
}
else
{
/* We have to go row by row */
ginfo("Falling-back to row by row mode\n");
jd9851_wrram(priv, buffer, row_size, stride - row_size, rows);
}
return OK;
}
/****************************************************************************
* Name: jd9851_getrun
*
* Description:
* This method can be used to read a partial raster line from the LCD:
*
* dev - The lcd device
* row - Starting row to read from (range: 0 <= row < yres)
* col - Starting column to read read (range: 0 <= col <= xres-npixels)
* buffer - The buffer in which to return the run read from the LCD
* npixels - The number of pixels to read from the LCD
* (range: 0 < npixels <= xres-col)
*
****************************************************************************/
#ifndef CONFIG_LCD_NOGETRUN
static int jd9851_getrun(FAR struct lcd_dev_s *dev,
fb_coord_t row, fb_coord_t col,
FAR uint8_t *buffer, size_t npixels)
{
FAR struct jd9851_dev_s *priv = (FAR struct jd9851_dev_s *)dev;
FAR uint16_t *dest = (FAR uint16_t *)buffer;
ginfo("row: %d col: %d npixels: %d\n", row, col, npixels);
DEBUGASSERT(buffer && ((uintptr_t)buffer & 1) == 0);
jd9851_setcursor(priv, col, row, col + npixels - 1, row);
jd9851_rdram(priv, dest, npixels);
return OK;
}
#endif
/****************************************************************************
* Name: jd9851_getvideoinfo
*
* Description:
* Get information about the LCD video controller configuration.
*
****************************************************************************/
static int jd9851_getvideoinfo(FAR struct lcd_dev_s *dev,
FAR struct fb_videoinfo_s *vinfo)
{
DEBUGASSERT(dev && vinfo);
lcdinfo("fmt: %d xres: %d yres: %d nplanes: 1\n",
JD9851_COLORFMT, JD9851_XRES, JD9851_YRES);
vinfo->fmt = JD9851_COLORFMT; /* Color format: RGB16-565: RRRR RGGG GGGB BBBB */
vinfo->xres = JD9851_XRES; /* Horizontal resolution in pixel columns */
vinfo->yres = JD9851_YRES; /* Vertical resolution in pixel rows */
vinfo->nplanes = 1; /* Number of color planes supported */
return OK;
}
/****************************************************************************
* Name: jd9851_getplaneinfo
*
* Description:
* Get information about the configuration of each LCD color plane.
*
****************************************************************************/
static int jd9851_getplaneinfo(FAR struct lcd_dev_s *dev,
unsigned int planeno,
FAR struct lcd_planeinfo_s *pinfo)
{
FAR struct jd9851_dev_s *priv = (FAR struct jd9851_dev_s *)dev;
DEBUGASSERT(dev && pinfo && planeno == 0);
lcdinfo("planeno: %d bpp: %d\n", planeno, JD9851_BPP);
pinfo->putrun = jd9851_putrun; /* Put a run into LCD memory */
pinfo->putarea = jd9851_putarea; /* Put an area into LCD */
#ifndef CONFIG_LCD_NOGETRUN
pinfo->getrun = jd9851_getrun; /* Get a run from LCD memory */
#endif
pinfo->buffer = (FAR uint8_t *)priv->runbuffer; /* Run scratch buffer */
pinfo->bpp = priv->bpp; /* Bits-per-pixel */
pinfo->dev = dev; /* The lcd device */
return OK;
}
/****************************************************************************
* Name: jd9851_getpower
****************************************************************************/
static int jd9851_getpower(FAR struct lcd_dev_s *dev)
{
FAR struct jd9851_dev_s *priv = (FAR struct jd9851_dev_s *)dev;
lcdinfo("power: %d\n", priv->power);
return priv->power;
}
/****************************************************************************
* Name: jd9851_setpower
****************************************************************************/
static int jd9851_setpower(FAR struct lcd_dev_s *dev, int power)
{
FAR struct jd9851_dev_s *priv = (FAR struct jd9851_dev_s *)dev;
lcdinfo("power: %d\n", power);
DEBUGASSERT((unsigned)power <= CONFIG_LCD_MAXPOWER);
/* Set new power level */
if (power > 0)
{
/* Turn on the display */
jd9851_display(priv, true);
/* Save the power */
priv->power = power;
}
else
{
/* Turn off the display */
jd9851_display(priv, false);
/* Save the power */
priv->power = 0;
}
return OK;
}
/****************************************************************************
* Name: jd9851_getcontrast
*
* Description:
* Get the current contrast setting (0-CONFIG_LCD_MAXCONTRAST).
*
****************************************************************************/
static int jd9851_getcontrast(FAR struct lcd_dev_s *dev)
{
lcdinfo("Not implemented\n");
return -ENOSYS;
}
/****************************************************************************
* Name: jd9851_setcontrast
*
* Description:
* Set LCD panel contrast (0-CONFIG_LCD_MAXCONTRAST).
*
****************************************************************************/
static int jd9851_setcontrast(FAR struct lcd_dev_s *dev,
unsigned int contrast)
{
lcdinfo("contrast: %d\n", contrast);
return -ENOSYS;
}
/****************************************************************************
* Public Functions
****************************************************************************/
/****************************************************************************
* Name: jd9851_initialize
*
* Description:
* Initialize the JD9851 video hardware. The initial state of the
* LCD is fully initialized, display memory cleared, and the LCD ready
* to use, but with the power setting at 0 (full off == sleep mode).
*
* Returned Value:
*
* On success, this function returns a reference to the LCD object for
* the specified LCD. NULL is returned on any failure.
*
****************************************************************************/
FAR struct lcd_dev_s *jd9851_lcdinitialize(FAR struct spi_dev_s *spi)
{
FAR struct jd9851_dev_s *priv = &g_lcddev;
/* Initialize the driver data structure */
priv->dev.getvideoinfo = jd9851_getvideoinfo;
priv->dev.getplaneinfo = jd9851_getplaneinfo;
priv->dev.getpower = jd9851_getpower;
priv->dev.setpower = jd9851_setpower;
priv->dev.getcontrast = jd9851_getcontrast;
priv->dev.setcontrast = jd9851_setcontrast;
priv->spi = spi;
/* Init the hardware and clear the display */
jd9851_init(priv);
jd9851_display(priv, false);
jd9851_sleep(priv, false);
jd9851_bpp(priv, JD9851_BPP);
jd9851_setorientation(priv);
jd9851_fill(priv, 0x0000);
jd9851_display(priv, true);
return &priv->dev;
}
#endif /* CONFIG_LCD_JD9851 */
Reference in New Issue View Git Blame Copy Permalink