126 lines
4.6 KiB
C
126 lines
4.6 KiB
C
/****************************************************************************
|
|
* include/nuttx/sensors/mpl115a.h
|
|
*
|
|
* Licensed to the Apache Software Foundation (ASF) under one or more
|
|
* contributor license agreements. See the NOTICE file distributed with
|
|
* this work for additional information regarding copyright ownership. The
|
|
* ASF licenses this file to you under the Apache License, Version 2.0 (the
|
|
* "License"); you may not use this file except in compliance with the
|
|
* License. You may obtain a copy of the License at
|
|
*
|
|
* http://www.apache.org/licenses/LICENSE-2.0
|
|
*
|
|
* Unless required by applicable law or agreed to in writing, software
|
|
* distributed under the License is distributed on an "AS IS" BASIS, WITHOUT
|
|
* WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. See the
|
|
* License for the specific language governing permissions and limitations
|
|
* under the License.
|
|
*
|
|
****************************************************************************/
|
|
|
|
#ifndef __INCLUDE_NUTTX_SENSORS_MPL115A_H
|
|
#define __INCLUDE_NUTTX_SENSORS_MPL115A_H
|
|
|
|
/****************************************************************************
|
|
* Included Files
|
|
****************************************************************************/
|
|
|
|
#include <nuttx/config.h>
|
|
|
|
#if defined(CONFIG_SPI) && defined(CONFIG_SENSORS_MPL115A)
|
|
|
|
/****************************************************************************
|
|
* Pre-processor Definitions
|
|
****************************************************************************/
|
|
|
|
/* Configuration ************************************************************/
|
|
|
|
/* Prerequisites:
|
|
*
|
|
* CONFIG_SENSORS_MPL115A
|
|
* Enables support for the MPL115A driver
|
|
* CONFIG_MPL115A_REGDEBUG
|
|
* Enable very low register-level debug output.
|
|
* Requires CONFIG_DEBUG_FEATURES.
|
|
*/
|
|
|
|
/* There are two types of MPL115A chips.
|
|
* The MPL115A1 communicates with the target CPU via a SPI interface.
|
|
* The MPL115A2 communicates via I2C interface.
|
|
* Note: This driver only supports MPL115A1 (SPI Interface).
|
|
*/
|
|
|
|
/* SPI **********************************************************************/
|
|
|
|
/* The device always operates in mode 0 */
|
|
|
|
#define MPL115A_SPI_MODE SPIDEV_MODE0 /* Mode 0 */
|
|
|
|
/* SPI frequency */
|
|
|
|
#define MPL115A_SPI_MAXFREQUENCY 800000 /* 8MHz */
|
|
|
|
/* MPL115A Registers ********************************************************/
|
|
|
|
/* Register Addresses */
|
|
|
|
#define MPL115A_BASE_CMD 0x80
|
|
#define MPL115A_PADC_MSB 0x00 /* 10-bit Pressure ADC output value MSB */
|
|
#define MPL115A_PADC_LSB 0x01 /* 10-bit Pressure ADC output value LSB */
|
|
#define MPL115A_TADC_MSB 0x02 /* 10-bit Temperature ADC output value MSB */
|
|
#define MPL115A_TADC_LSB 0x03 /* 10-bit Temperature ADC output value LSB */
|
|
#define MPL115A_A0_MSB 0x04 /* a0 coefficient MSB */
|
|
#define MPL115A_A0_LSB 0x05 /* a0 coefficient LSB */
|
|
#define MPL115A_B1_MSB 0x06 /* b1 coefficient MSB */
|
|
#define MPL115A_B1_LSB 0x07 /* b1 coefficient LSB */
|
|
#define MPL115A_B2_MSB 0x08 /* b2 coefficient MSB */
|
|
#define MPL115A_B2_LSB 0x09 /* b2 coefficient LSB */
|
|
#define MPL115A_C12_MSB 0x0a /* c12 coefficient MSB */
|
|
#define MPL115A_C12_LSB 0x0b /* c12 coefficient LSB */
|
|
/* 0x0c - 0x11 are reserved */
|
|
#define MPL115A_CONVERT 0x12 /* Start Pressure and Temperature Conversion */
|
|
|
|
/****************************************************************************
|
|
* Public Types
|
|
****************************************************************************/
|
|
|
|
struct spi_dev_s;
|
|
|
|
/****************************************************************************
|
|
* Public Function Prototypes
|
|
****************************************************************************/
|
|
|
|
#ifdef __cplusplus
|
|
#define EXTERN extern "C"
|
|
extern "C"
|
|
{
|
|
#else
|
|
#define EXTERN extern
|
|
#endif
|
|
|
|
/****************************************************************************
|
|
* Name: mpl115a_register
|
|
*
|
|
* Description:
|
|
* Register the MPL115A character device as 'devpath'
|
|
*
|
|
* Input Parameters:
|
|
* devpath - The full path to the driver to register. E.g., "/dev/temp0"
|
|
* spi - An instance of the SPI interface to use to communicate with
|
|
* MPL115A
|
|
*
|
|
* Returned Value:
|
|
* Zero (OK) on success; a negated errno value on failure.
|
|
*
|
|
****************************************************************************/
|
|
|
|
int mpl115a_register(FAR const char *devpath, FAR struct spi_dev_s *spi);
|
|
|
|
#undef EXTERN
|
|
#ifdef __cplusplus
|
|
}
|
|
#endif
|
|
|
|
#endif /* CONFIG_SPI && CONFIG_SENSORS_MPL115A */
|
|
#endif /* __INCLUDE_NUTTX_SENSORS_MPL115A_H */
|