78 lines
2.8 KiB
Makefile
78 lines
2.8 KiB
Makefile
############################################################################
|
|
# tools/esp32c3/Config.mk
|
|
#
|
|
# Licensed to the Apache Software Foundation (ASF) under one or more
|
|
# contributor license agreements. See the NOTICE file distributed with
|
|
# this work for additional information regarding copyright ownership. The
|
|
# ASF licenses this file to you under the Apache License, Version 2.0 (the
|
|
# "License"); you may not use this file except in compliance with the
|
|
# License. You may obtain a copy of the License at
|
|
#
|
|
# http://www.apache.org/licenses/LICENSE-2.0
|
|
#
|
|
# Unless required by applicable law or agreed to in writing, software
|
|
# distributed under the License is distributed on an "AS IS" BASIS, WITHOUT
|
|
# WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. See the
|
|
# License for the specific language governing permissions and limitations
|
|
# under the License.
|
|
#
|
|
############################################################################
|
|
|
|
# These are the macros that will be used in the NuttX make system to compile
|
|
# and assemble source files and to insert the resulting object files into an
|
|
# archive. These replace the default definitions at tools/Config.mk
|
|
|
|
ifdef ESPTOOL_BINDIR
|
|
BL_OFFSET=0x0
|
|
PT_OFFSET=0x8000
|
|
BOOTLOADER=$(ESPTOOL_BINDIR)/bootloader.bin
|
|
PARTITION_TABLE=$(ESPTOOL_BINDIR)/partition-table.bin
|
|
FLASH_BL=$(BL_OFFSET) $(BOOTLOADER)
|
|
FLASH_PT=$(PT_OFFSET) $(PARTITION_TABLE)
|
|
endif
|
|
|
|
ifeq ($(CONFIG_ESP32C3_FLASH_2M),y)
|
|
FLASH_SIZE="2MB"
|
|
else ifeq ($(CONFIG_ESP32C3_FLASH_4M),y)
|
|
FLASH_SIZE="4MB"
|
|
else ifeq ($(CONFIG_ESP32C3_FLASH_8M),y)
|
|
FLASH_SIZE="8MB"
|
|
else ifeq ($(CONFIG_ESP32C3_FLASH_16M),y)
|
|
FLASH_SIZE="16MB"
|
|
endif
|
|
|
|
# POSTBUILD -- Perform post build operations
|
|
|
|
define POSTBUILD
|
|
$(Q) echo "MKIMAGE: ESP32-C3 binary"
|
|
$(Q) if ! esptool.py version 1>/dev/null 2>&1; then \
|
|
echo ""; \
|
|
echo "esptool.py not found. Please run: \"pip install esptool\""; \
|
|
echo "Or run: \"make -C $(TOPDIR)/tools/esp32c3\" to install all IDF tools."; \
|
|
echo ""; \
|
|
echo "Run make again to create the nuttx.bin image."; \
|
|
exit 1; \
|
|
fi
|
|
$(Q) if [ -z $(FLASH_SIZE) ]; then \
|
|
echo "Missing Flash memory size configuration for the ESP32-C3 chip."; \
|
|
exit 1; \
|
|
fi
|
|
esptool.py --chip esp32c3 elf2image --flash_mode dio --flash_size $(FLASH_SIZE) -o nuttx.bin nuttx
|
|
$(Q) echo "Generated: nuttx.bin (ESP32-C3 compatible)"
|
|
endef
|
|
|
|
# ESPTOOL_BAUD -- Serial port baud rate used when flashing/reading via esptool.py
|
|
|
|
ESPTOOL_BAUD ?= 921600
|
|
|
|
# DOWNLOAD -- Download binary image via esptool.py
|
|
|
|
define DOWNLOAD
|
|
$(Q) if [ -z $(ESPTOOL_PORT) ]; then \
|
|
echo "DOWNLOAD error: Missing serial port device argument."; \
|
|
echo "USAGE: make download ESPTOOL_PORT=<port> [ ESPTOOL_BAUD=<baud> ]"; \
|
|
exit 1; \
|
|
fi
|
|
esptool.py --chip esp32c3 --port $(ESPTOOL_PORT) --baud $(ESPTOOL_BAUD) write_flash $(FLASH_BL) $(FLASH_PT) 0x10000 $(1).bin
|
|
endef
|