incubator-nuttx/boards/mips/pic32mx/sure-pic32mx/include/board.h

170 lines
6.3 KiB
C

/****************************************************************************
* boards/mips/pic32mx/sure-pic32mx/include/board.h
*
* Licensed to the Apache Software Foundation (ASF) under one or more
* contributor license agreements. See the NOTICE file distributed with
* this work for additional information regarding copyright ownership. The
* ASF licenses this file to you under the Apache License, Version 2.0 (the
* "License"); you may not use this file except in compliance with the
* License. You may obtain a copy of the License at
*
* http://www.apache.org/licenses/LICENSE-2.0
*
* Unless required by applicable law or agreed to in writing, software
* distributed under the License is distributed on an "AS IS" BASIS, WITHOUT
* WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. See the
* License for the specific language governing permissions and limitations
* under the License.
*
****************************************************************************/
#ifndef __BOARDS_MIPS_PIC32MX_SURE_PIC32MX_INCLUDE_BOARD_H
#define __BOARDS_MIPS_PIC32MX_SURE_PIC32MX_INCLUDE_BOARD_H
/****************************************************************************
* Included Files
****************************************************************************/
#include <nuttx/config.h>
/****************************************************************************
* Pre-processor Definitions
****************************************************************************/
/* Configuration ************************************************************/
/* Clocking *****************************************************************/
/* Crystal frequencies */
#define BOARD_POSC_FREQ 20000000 /* Primary OSC XTAL frequency (20MHz) */
#define BOARD_SOSC_FREQ 32768 /* Secondary OSC XTAL frequency (32.768KHz) */
/* Oscillator modes */
#define BOARD_FNOSC_POSCPLL 1 /* Use primary oscillator w/PLL */
#define BOARD_POSC_HSMODE 1 /* High-speed crystal (HS) mode */
/* PLL configuration and resulting CPU clock.
* CPU_CLOCK = ((POSC_FREQ / IDIV) * MULT) / ODIV
*/
#define BOARD_PLL_INPUT BOARD_POSC_FREQ
#define BOARD_PLL_IDIV 5 /* PLL input divider */
#define BOARD_PLL_MULT 15 /* PLL multiplier */
#define BOARD_PLL_ODIV 1 /* PLL output divider */
#define BOARD_CPU_CLOCK 60000000 /* CPU clock (60MHz = (20MHz / 5) * 15 / 1) */
/* USB PLL configuration.
* USB_CLOCK = ((POSC_XTAL / IDIV) * 24) / 2
*/
#define BOARD_UPLL_IDIV 5 /* USB PLL divider */
#define BOARD_USB_CLOCK 48000000 /* USB clock ((20MHz / 5) * 24) / 2 */
/* Peripheral clock is *not* divided down from CPU clock.
* PBCLOCK = CPU_CLOCK / PBDIV
*/
#define BOARD_PBDIV 1 /* Peripheral clock divisor (PBDIV) */
#define BOARD_PBCLOCK 60000000 /* Peripheral clock (PBCLK = 60MHz/1) */
/* Watchdog pre-scaler (re-visit) */
#define BOARD_WD_ENABLE 0 /* Watchdog is disabled */
#define BOARD_WD_PRESCALER 8 /* Watchdog pre-scaler */
/* Timer 1 is a type A timer and is used as system clock. It can be clocked
* with either the SOSC or the PBCLOCK. We will use the PBCLOCK because it
* is much more accurate.
*/
#undef BOARD_TIMER1_SOSC
/* LED definitions **********************************************************/
/* The Sure DB_DP11215 PIC32 Storage Demo Board board has five LEDs. One
* (D4, lablel "Power") is not controllable by software. Four are
* controllable by software:
*
* D7 "USB" Yellow RD7 Low illuminates
* D8 "SD" Yellow RD6 Low illuminates
* D9 "Flash" Yellow RF0 Low illuminates
* D10 "Error" Red RF1 Low illuminates
*/
/* ON OFF */
/* USB SD FLASH ERROR USB SD FLASH ERROR */
#define LED_STARTED 0 /* OFF OFF OFF OFF --- --- --- --- */
#define LED_HEAPALLOCATE 1 /* ON OFF N/C N/C --- --- --- --- */
#define LED_IRQSENABLED 2 /* OFF ON N/C N/C --- --- --- --- */
#define LED_STACKCREATED 3 /* ON ON N/C N/C --- --- --- --- */
#define LED_INIRQ 4 /* N/C N/C ON N/C N/C N/C OFF N/C */
#define LED_SIGNAL 4 /* N/C N/C ON N/C N/C N/C OFF N/C */
#define LED_ASSERTION 4 /* N/C N/C ON N/C N/C N/C OFF N/C */
#define LED_PANIC 5 /* N/C N/C N/C ON N/C N/C N/C OFF */
#define LED_NVALUES 6
/* The Sure DB-DP11212 PIC32 General Purpose Demo Board does not have any
* user controllable LEDs, but does does have a segment LED display.
* That display is however, obscured by the larger segment display attached
* to the board and, so, is not supported.
*/
/* For distinguishing individual LEDs */
#define LED_USB 0
#define LED_SD 1
#define LED_FLASH 2
#define LED_ERROR 3
/* Button Definitions *******************************************************/
/* The Sure PIC32MX board has three buttons.
*
* SW1 (SW_UP, left arrow) RB3 Pulled high, GND/low when depressed
* SW2 (SW_DOWN, down/right arrow) RB2 Pulled high, GND/low when depressed
* SW3 (SW_OK, right arrow) RB4 Pulled high, GND/low when depressed
*/
#define BUTTON_SW1 0
#define BUTTON_SW2 1
#define BUTTON_SW3 2
#define NUM_BUTTONS 3
#define BUTTON_SW1_BIT (1 << BUTTON_SW1)
#define BUTTON_SW2_BIT (1 << BUTTON_SW2)
#define BUTTON_SW3_BIT (1 << BUTTON_SW3)
/****************************************************************************
* Public Types
****************************************************************************/
#ifndef __ASSEMBLY__
/****************************************************************************
* Inline Functions
****************************************************************************/
/****************************************************************************
* Public Function Prototypes
****************************************************************************/
#ifdef __cplusplus
#define EXTERN extern "C"
extern "C"
{
#else
#define EXTERN extern
#endif
#undef EXTERN
#ifdef __cplusplus
}
#endif
#endif /* __ASSEMBLY__ */
#endif /* __BOARDS_MIPS_PIC32MX_SURE_PIC32MX_INCLUDE_BOARD_H */