202 lines
7.5 KiB
C
202 lines
7.5 KiB
C
/****************************************************************************
|
|
* boards/mips/pic32mx/pic32mx7mmb/include/board.h
|
|
*
|
|
* Licensed to the Apache Software Foundation (ASF) under one or more
|
|
* contributor license agreements. See the NOTICE file distributed with
|
|
* this work for additional information regarding copyright ownership. The
|
|
* ASF licenses this file to you under the Apache License, Version 2.0 (the
|
|
* "License"); you may not use this file except in compliance with the
|
|
* License. You may obtain a copy of the License at
|
|
*
|
|
* http://www.apache.org/licenses/LICENSE-2.0
|
|
*
|
|
* Unless required by applicable law or agreed to in writing, software
|
|
* distributed under the License is distributed on an "AS IS" BASIS, WITHOUT
|
|
* WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. See the
|
|
* License for the specific language governing permissions and limitations
|
|
* under the License.
|
|
*
|
|
****************************************************************************/
|
|
|
|
#ifndef __BOARDS_MIPS_PIC32MX_PIC32MX7MMB_INCLUDE_BOARD_H
|
|
#define __BOARDS_MIPS_PIC32MX_PIC32MX7MMB_INCLUDE_BOARD_H
|
|
|
|
/****************************************************************************
|
|
* Included Files
|
|
****************************************************************************/
|
|
|
|
#include <nuttx/config.h>
|
|
|
|
#ifndef __ASSEMBLY__
|
|
# include <stdbool.h>
|
|
#endif
|
|
|
|
/****************************************************************************
|
|
* Pre-processor Definitions
|
|
****************************************************************************/
|
|
|
|
/* Configuration ************************************************************/
|
|
|
|
/* Clocking *****************************************************************/
|
|
|
|
/* Crystal frequencies */
|
|
|
|
#define BOARD_POSC_FREQ 8000000 /* Primary OSC XTAL frequency (8MHz) */
|
|
#define BOARD_SOSC_FREQ 32768 /* Secondary OSC XTAL frequency (32.768KHz) */
|
|
|
|
/* Oscillator modes */
|
|
|
|
#define BOARD_FNOSC_POSCPLL 1 /* Use primary oscillator w/PLL */
|
|
#define BOARD_POSC_XTMODE 1 /* Resonator, crystal or resonator (XT) mode */
|
|
#undef BOARD_POSC_SWITCH /* Use FRC until POSC stabilizes, then switch */
|
|
#undef BOARD_POSC_FSCM /* Switch to FRC if POSC fails */
|
|
#define BOARD_SOSC_ENABLE 1 /* Enable Secondary Oscillator */
|
|
#define BOARD_SOSC_IESO 1 /* Internal External Switchover mode is enabled */
|
|
|
|
/* PLL configuration and resulting CPU clock.
|
|
* CPU_CLOCK = ((POSC_FREQ / IDIV) * MULT) / ODIV
|
|
*/
|
|
|
|
#define BOARD_PLL_INPUT BOARD_POSC_FREQ
|
|
#define BOARD_PLL_IDIV 2 /* PLL input divider */
|
|
#define BOARD_PLL_MULT 20 /* PLL multiplier */
|
|
#define BOARD_PLL_ODIV 1 /* PLL output divider */
|
|
|
|
#define BOARD_CPU_CLOCK 80000000 /* CPU clock (80MHz = 8MHz * 20 / 2) */
|
|
|
|
/* USB PLL configuration.
|
|
* USB_CLOCK = ((POSC_XTAL / IDIV) * 24) / 2
|
|
*/
|
|
|
|
#define BOARD_UPLL_IDIV 2 /* USB PLL divider (revisit) */
|
|
#define BOARD_USB_CLOCK 48000000 /* USB clock (8MHz / 2) * 24 / 2) */
|
|
|
|
/* Peripheral clock is divided down from CPU clock.
|
|
* PBCLOCK = CPU_CLOCK / PBDIV
|
|
*/
|
|
|
|
#define BOARD_PBDIV 2 /* Peripheral clock divisor (PBDIV) */
|
|
#define BOARD_PBCLOCK 40000000 /* Peripheral clock (PBCLK = 80MHz/2) */
|
|
|
|
/* Watchdog pre-scaler (re-visit) */
|
|
|
|
#define BOARD_WD_ENABLE 0 /* Watchdog is disabled */
|
|
#define BOARD_WD_PRESCALER 8 /* Watchdog pre-scaler */
|
|
|
|
/* Ethernet MII clocking.
|
|
*
|
|
* The clock divider used to create the MII Management Clock (MDC). The MIIM
|
|
* module uses the SYSCLK as an input clock. According to the IEEE 802.3
|
|
* Specification this should be no faster than 2.5 MHz. However, some PHYs
|
|
* support clock rates up to 12.5 MHz.
|
|
*/
|
|
|
|
#define BOARD_EMAC_MIIM_DIV 32 /* Ideal: 80MHz/32 = 2.5MHz */
|
|
|
|
/* LED definitions **********************************************************/
|
|
|
|
/* LED Configuration ********************************************************/
|
|
|
|
/* The Mikroelektronika PIC32MX7 MMB has 3 user LEDs labeled LED0-2 in the
|
|
* schematics:
|
|
*
|
|
* --- ----- --------------------------------------------------------------
|
|
* PIN Board Notes
|
|
* --- ----- --------------------------------------------------------------
|
|
* RA0 LED0 Pulled-up, low value illuminates
|
|
* RA1 LED1 Pulled-up, low value illuminates
|
|
* RD9 LED2 Pulled-up, low value illuminates
|
|
* RA9 LED4 Not available for general use*, indicates MMC/SD activity
|
|
* --- LED5 Not controllable by software, indicates power-on
|
|
*
|
|
* * RA9 is also the SD chip select. It will illuminate whenever the SD card
|
|
* is selected. If SD is not used, then LED4 could also be used as a user-
|
|
* controlled LED.
|
|
*/
|
|
|
|
/* LED index values for use with board_userled() */
|
|
|
|
#define PIC32MX_PIC32MX7MMB_LED0 0
|
|
#define PIC32MX_PIC32MX7MMB_LED1 1
|
|
#define PIC32MX_PIC32MX7MMB_LED2 2
|
|
#define PIC32MX_PIC32MX7MMB_NLEDS 3
|
|
|
|
/* LED bits for use with board_userled_all() */
|
|
|
|
#define PIC32MX_PIC32MX7MMB_LED0_BIT (1 << PIC32MX_PIC32MX7MMB_LED0)
|
|
#define PIC32MX_PIC32MX7MMB_LED1_BIT (1 << PIC32MX_PIC32MX7MMB_LED1)
|
|
#define PIC32MX_PIC32MX7MMB_LED2_BIT (1 << PIC32MX_PIC32MX7MMB_LED2)
|
|
|
|
/* If CONFIG_ARCH_LEDs is defined, then NuttX will control the 3 LEDs
|
|
* on board the Mikroelektronika PIC32MX7 MMB. The following definitions
|
|
* describe how NuttX controls the LEDs:
|
|
*
|
|
* ON OFF
|
|
* ------------------------- ---- ---- ---- ---- ---- ----
|
|
* LED0 LED1 LED2 LED0 LED1 LED2
|
|
* ------------------------- ---- ---- ---- ---- ---- ----
|
|
* LED_STARTED 0 OFF OFF OFF --- --- ---
|
|
* LED_HEAPALLOCATE 1 ON OFF N/C --- --- ---
|
|
* LED_IRQSENABLED 2 OFF ON N/C --- --- ---
|
|
* LED_STACKCREATED 3 ON ON N/C --- --- ---
|
|
* LED_INIRQ 4 N/C N/C ON N/C N/C OFF
|
|
* LED_SIGNAL 4 N/C N/C ON N/C N/C OFF
|
|
* LED_ASSERTION 4 N/C N/C ON N/C N/C OFF
|
|
* LED_PANIC 5 ON N/C N/C OFF N/C N/C
|
|
*/
|
|
|
|
#define LED_STARTED 0
|
|
#define LED_HEAPALLOCATE 1
|
|
#define LED_IRQSENABLED 2
|
|
#define LED_STACKCREATED 3
|
|
#define LED_INIRQ 4
|
|
#define LED_SIGNAL 4
|
|
#define LED_ASSERTION 4
|
|
#define LED_PANIC 5
|
|
|
|
#define LED_NVALUES 6
|
|
|
|
/* Switch definitions *******************************************************/
|
|
|
|
/* The Mikroelektronika PIC32MX7 MMB has a joystick:
|
|
*
|
|
* ------ -------- --------------------------
|
|
* GPIO SIGNAL BOARD CONNECTION
|
|
* ------ -------- --------------------------
|
|
* RB0 JOY-A Joystick A, HDR1 pin 24
|
|
* RB2 JOY-C Joystick C, HDR1 pin 22
|
|
* RB1 JOY-B Joystick B, HDR1 pin 23
|
|
* RB3 JOY-D Joystick D, HDR1 pin 21
|
|
* RA10 JOY-CP Joystick CP, HDR1 pin 25
|
|
*/
|
|
|
|
/****************************************************************************
|
|
* Public Types
|
|
****************************************************************************/
|
|
|
|
#ifndef __ASSEMBLY__
|
|
|
|
/****************************************************************************
|
|
* Inline Functions
|
|
****************************************************************************/
|
|
|
|
#ifdef __cplusplus
|
|
#define EXTERN extern "C"
|
|
extern "C"
|
|
{
|
|
#else
|
|
#define EXTERN extern
|
|
#endif
|
|
|
|
/****************************************************************************
|
|
* Public Function Prototypes
|
|
****************************************************************************/
|
|
|
|
#undef EXTERN
|
|
#ifdef __cplusplus
|
|
}
|
|
#endif
|
|
|
|
#endif /* __ASSEMBLY__ */
|
|
#endif /* __BOARDS_MIPS_PIC32MX_PIC32MX7MMB_INCLUDE_BOARD_H */
|