/**************************************************************************** * drivers/net/lan91c111.h * * Licensed to the Apache Software Foundation (ASF) under one or more * contributor license agreements. See the NOTICE file distributed with * this work for additional information regarding copyright ownership. The * ASF licenses this file to you under the Apache License, Version 2.0 (the * "License"); you may not use this file except in compliance with the * License. You may obtain a copy of the License at * * http://www.apache.org/licenses/LICENSE-2.0 * * Unless required by applicable law or agreed to in writing, software * distributed under the License is distributed on an "AS IS" BASIS, WITHOUT * WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. See the * License for the specific language governing permissions and limitations * under the License. * ****************************************************************************/ #ifndef __DRIVERS_NET_LAN91C111_H #define __DRIVERS_NET_LAN91C111_H /**************************************************************************** * Included Files ****************************************************************************/ #include /**************************************************************************** * Pre-processor Definitions ****************************************************************************/ /* Bank Select Register: * * yyyy yyyy 0000 00xx * xx = bank number * yyyy yyyy = 0x33, for identification purposes. */ #define BANK_SELECT 14 /* Transmit Control Register * BANK 0 */ #define TCR_REG 0x0000 #define TCR_ENABLE 0x0001 /* When 1 we can transmit */ #define TCR_LOOP 0x0002 /* Controls output pin LBK */ #define TCR_FORCOL 0x0004 /* When 1 will force a collision */ #define TCR_PAD_EN 0x0080 /* When 1 will pad tx frames < 64 bytes w/0 */ #define TCR_NOCRC 0x0100 /* When 1 will not append CRC to tx frames */ #define TCR_MON_CSN 0x0400 /* When 1 tx monitors carrier */ #define TCR_FDUPLX 0x0800 /* When 1 enables full duplex operation */ #define TCR_STP_SQET 0x1000 /* When 1 stops tx if Signal Quality Error */ #define TCR_EPH_LOOP 0x2000 /* When 1 enables EPH block loopback */ #define TCR_SWFDUP 0x8000 /* When 1 enables Switched Full Duplex mode */ #define TCR_CLEAR 0 /* do NOTHING */ /* the default settings for the TCR register : */ #define TCR_DEFAULT (TCR_ENABLE | TCR_PAD_EN) /* EPH Status Register * BANK 0 */ #define EPH_STATUS_REG 0x0002 #define ES_TX_SUC 0x0001 /* Last TX was successful */ #define ES_SNGL_COL 0x0002 /* Single collision detected for last tx */ #define ES_MUL_COL 0x0004 /* Multiple collisions detected for last tx */ #define ES_LTX_MULT 0x0008 /* Last tx was a multicast */ #define ES_16COL 0x0010 /* 16 Collisions Reached */ #define ES_SQET 0x0020 /* Signal Quality Error Test */ #define ES_LTXBRD 0x0040 /* Last tx was a broadcast */ #define ES_TXDEFR 0x0080 /* Transmit Deferred */ #define ES_LATCOL 0x0200 /* Late collision detected on last tx */ #define ES_LOSTCARR 0x0400 /* Lost Carrier Sense */ #define ES_EXC_DEF 0x0800 /* Excessive Deferral */ #define ES_CTR_ROL 0x1000 /* Counter Roll Over indication */ #define ES_LINK_OK 0x4000 /* Driven by inverted value of nLNK pin */ #define ES_TXUNRN 0x8000 /* Tx Underrun */ #define ES_ERRORS (ES_TXUNRN | ES_LOSTCARR | ES_LATCOL | ES_SQET | ES_16COL) /* Receive Control Register * BANK 0 */ #define RCR_REG 0x0004 #define RCR_RX_ABORT 0x0001 /* Set if a rx frame was aborted */ #define RCR_PRMS 0x0002 /* Enable promiscuous mode */ #define RCR_ALMUL 0x0004 /* When set accepts all multicast frames */ #define RCR_RXEN 0x0100 /* IF this is set, we can receive packets */ #define RCR_STRIP_CRC 0x0200 /* When set strips CRC from rx packets */ #define RCR_ABORT_ENB 0x2000 /* When set will abort rx on collision */ #define RCR_FILT_CAR 0x4000 /* When set filters leading 12 bit s of carrier */ #define RCR_SOFTRST 0x8000 /* resets the chip */ /* the normal settings for the RCR register : */ #ifdef CONFIG_NET_PROMISCUOUS # define RCR_DEFAULT (RCR_STRIP_CRC | RCR_RXEN | RCR_PRMS) #else # define RCR_DEFAULT (RCR_STRIP_CRC | RCR_RXEN) #endif #define RCR_CLEAR 0x0 /* set it to a base state */ /* Counter Register * BANK 0 */ #define COUNTER_REG 0x0006 /* Memory Information Register * BANK 0 */ #define MIR_REG 0x0008 #define MIR_FREE_MASK 0xff00 /* Receive/Phy Control Register * BANK 0 */ #define RPC_REG 0x000a #define RPC_SPEED 0x2000 /* When 1 PHY is in 100Mbps mode. */ #define RPC_DPLX 0x1000 /* When 1 PHY is in Full-Duplex Mode */ #define RPC_ANEG 0x0800 /* When 1 PHY is in Auto-Negotiate Mode */ #define RPC_LSXA_SHFT 5 /* Bits to shift LS2A,LS1A,LS0A to lsb */ #define RPC_LSXB_SHFT 2 /* Bits to get LS2B,LS1B,LS0B to lsb */ #define RPC_LED_100_10 0x00 /* LED = 100Mbps OR's with 10Mbps link detect */ #define RPC_LED_RES 0x01 /* LED = Reserved */ #define RPC_LED_10 0x02 /* LED = 10Mbps link detect */ #define RPC_LED_FD 0x03 /* LED = Full Duplex Mode */ #define RPC_LED_TX_RX 0x04 /* LED = TX or RX packet occurred */ #define RPC_LED_100 0x05 /* LED = 100Mbps link detect */ #define RPC_LED_TX 0x06 /* LED = TX packet occurred */ #define RPC_LED_RX 0x07 /* LED = RX packet occurred */ #define RPC_DEFAULT (RPC_ANEG | RPC_SPEED | RPC_DPLX \ | (RPC_LED_100_10 << RPC_LSXA_SHFT) \ | (RPC_LED_TX_RX << RPC_LSXB_SHFT)) /* Bank 0 0x000c is reserved */ /* Bank Select Register * All Banks */ #define BSR_REG 0x000e /* Configuration Reg * BANK 1 */ #define CONFIG_REG 0x0100 #define CONFIG_EXT_PHY 0x0200 /* 1=external MII, 0=internal Phy */ #define CONFIG_GPCNTRL 0x0400 /* Inverse value drives pin nCNTRL */ #define CONFIG_NO_WAIT 0x1000 /* When 1 no extra wait states on ISA bus */ #define CONFIG_EPH_POWER_EN 0x8000 /* When 0 EPH is placed into low power mode. */ /* Default is powered-up, Internal Phy, Wait States, and pin nCNTRL=low */ #define CONFIG_DEFAULT (CONFIG_EPH_POWER_EN) #define CONFIG_CLEAR 0 /* Base Address Register * BANK 1 */ #define BASE_REG 0x0102 /* Individual Address Registers * BANK 1 */ #define ADDR0_REG 0x0104 #define ADDR1_REG 0x0106 #define ADDR2_REG 0x0108 /* General Purpose Register * BANK 1 */ #define GP_REG 0x010a /* Control Register * BANK 1 */ #define CTL_REG 0x010c #define CTL_RCV_BAD 0x4000 /* When 1 bad CRC packets are received */ #define CTL_AUTO_RELEASE 0x0800 /* When 1 tx pages are released automatically */ #define CTL_LE_ENABLE 0x0080 /* When 1 enables Link Error interrupt */ #define CTL_CR_ENABLE 0x0040 /* When 1 enables Counter Rollover interrupt */ #define CTL_TE_ENABLE 0x0020 /* When 1 enables Transmit Error interrupt */ #define CTL_EEPROM_SELECT 0x0004 /* Controls EEPROM reload & store */ #define CTL_RELOAD 0x0002 /* When set reads EEPROM into registers */ #define CTL_STORE 0x0001 /* When set stores registers into EEPROM */ #define CTL_DEFAULT (CTL_AUTO_RELEASE) #define CTL_CLEAR 0 /* MMU Command Register * BANK 2 */ #define MMU_CMD_REG 0x0200 #define MC_BUSY 1 /* When 1 the last release has not completed */ #define MC_NOP (0<<5) /* No Op */ #define MC_ALLOC (1<<5) /* OR with number of 256 byte packets */ #define MC_RESET (2<<5) /* Reset MMU to initial state */ #define MC_REMOVE (3<<5) /* Remove the current rx packet */ #define MC_RELEASE (4<<5) /* Remove and release the current rx packet */ #define MC_FREEPKT (5<<5) /* Release packet in PNR register */ #define MC_ENQUEUE (6<<5) /* Enqueue the packet for transmit */ #define MC_RSTTXFIFO (7<<5) /* Reset the TX FIFOs */ /* Packet Number Register * BANK 2 */ #define PN_REG 0x0202 /* Allocation Result Register * BANK 2 */ #define AR_REG 0x0203 #define AR_FAILED 0x80 /* Allocation Failed */ /* TX FIFO Ports Register * BANK 2 */ #define TXFIFO_REG 0x0204 #define TXFIFO_TEMPTY 0x80 /* TX FIFO Empty */ /* RX FIFO Ports Register * BANK 2 */ #define RXFIFO_REG 0x0205 #define RXFIFO_REMPTY 0x80 /* RX FIFO Empty */ #define FIFO_REG 0x0204 /* Pointer Register * BANK 2 */ #define PTR_REG 0x0206 #define PTR_RCV 0x8000 /* 1=Receive area, 0=Transmit area */ #define PTR_AUTOINC 0x4000 /* Auto increment the pointer on each access */ #define PTR_READ 0x2000 /* When 1 the operation is a read */ #define PTR_NOTEMPTY 0x0800 /* When 1 _do not_ write fifo DATA REG */ /* Data Register * BANK 2 */ #define DATA_REG 0x0208 /* Interrupt Status/Acknowledge Register * BANK 2 */ #define INT_REG 0x020c /* Interrupt Mask Register * BANK 2 */ #define IM_REG 0x020d #define IM_MDINT 0x80 /* PHY MI Register 18 Interrupt */ #define IM_ERCV_INT 0x40 /* Early Receive Interrupt */ #define IM_EPH_INT 0x20 /* Set by Etheret Protocol Handler section */ #define IM_RX_OVRN_INT 0x10 /* Set by Receiver Overruns */ #define IM_ALLOC_INT 0x08 /* Set when allocation request is completed */ #define IM_TX_EMPTY_INT 0x04 /* Set if the TX FIFO goes empty */ #define IM_TX_INT 0x02 /* Transmit Interrupt */ #define IM_RCV_INT 0x01 /* Receive Interrupt */ /* Multicast Table Registers * BANK 3 */ #define MCAST_REG1 0x0300 #define MCAST_REG2 0x0302 #define MCAST_REG3 0x0304 #define MCAST_REG4 0x0306 /* Management Interface Register (MII) * BANK 3 */ #define MII_REG 0x0308 #define MII_MSK_CRS100 0x4000 /* Disables CRS100 detection during tx half dup */ #define MII_MDOE 0x0008 /* MII Output Enable */ #define MII_MCLK 0x0004 /* MII Clock, pin MDCLK */ #define MII_MDI 0x0002 /* MII Input, pin MDI */ #define MII_MDO 0x0001 /* MII Output, pin MDO */ /* Revision Register * BANK 3 * ( hi: chip id low: rev # ) */ #define REV_REG 0x030a /* Early RCV Register * BANK 3 * this is NOT on SMC9192 */ #define ERCV_REG 0x030c #define ERCV_RCV_DISCRD 0x0080 /* When 1 discards a packet being received */ #define ERCV_THRESHOLD 0x001f /* ERCV Threshold Mask */ /* External Register * BANK 7 */ #define EXT_REG 0x0700 #define CHIP_9192 3 #define CHIP_9194 4 #define CHIP_9195 5 #define CHIP_9196 6 #define CHIP_91100 7 #define CHIP_91100FD 8 #define CHIP_91111FD 9 /* Transmit status bits * Same as ES_xxx */ /* Transmit control bits */ #define TC_ODD 0x20 #define TC_CRC 0x10 /* Receive status bits */ #define RS_ALGNERR 0x8000 #define RS_BRODCAST 0x4000 #define RS_BADCRC 0x2000 #define RS_ODDFRAME 0x1000 #define RS_TOOLONG 0x0800 #define RS_TOOSHORT 0x0400 #define RS_MULTICAST 0x0001 #define RS_ERRORS (RS_ALGNERR | RS_BADCRC | RS_TOOLONG | RS_TOOSHORT) /* Receive control bits */ #define RC_ODD 0x20 /* PHY IDs * LAN83C183 == LAN91C111 Internal PHY */ #define PHY_LAN83C183 0x0016f840 #define PHY_LAN83C180 0x02821c50 /* LPA full duplex flags */ #define MII_LPA_FULL (MII_LPA_10BASETXFULL | MII_LPA_100BASETXFULL) /* PHY Register Addresses (LAN91C111 Internal PHY) * * Generic PHY registers can be found in * * These phy registers are specific to our on-board phy. */ /* PHY Configuration Register 1 */ #define PHY_CFG1_REG 0x10 #define PHY_CFG1_LNKDIS 0x8000 /* 1=Rx Link Detect Function disabled */ #define PHY_CFG1_XMTDIS 0x4000 /* 1=TP Transmitter Disabled */ #define PHY_CFG1_XMTPDN 0x2000 /* 1=TP Transmitter Powered Down */ #define PHY_CFG1_BYPSCR 0x0400 /* 1=Bypass scrambler/descrambler */ #define PHY_CFG1_UNSCDS 0x0200 /* 1=Unscramble Idle Reception Disable */ #define PHY_CFG1_EQLZR 0x0100 /* 1=Rx Equalizer Disabled */ #define PHY_CFG1_CABLE 0x0080 /* 1=STP(150ohm), 0=UTP(100ohm) */ #define PHY_CFG1_RLVL0 0x0040 /* 1=Rx Squelch level reduced by 4.5db */ #define PHY_CFG1_TLVL_SHIFT 2 /* Transmit Output Level Adjust */ #define PHY_CFG1_TLVL_MASK 0x003c #define PHY_CFG1_TRF_MASK 0x0003 /* Transmitter Rise/Fall time */ /* PHY Configuration Register 2 */ #define PHY_CFG2_REG 0x11 #define PHY_CFG2_APOLDIS 0x0020 /* 1=Auto Polarity Correction disabled */ #define PHY_CFG2_JABDIS 0x0010 /* 1=Jabber disabled */ #define PHY_CFG2_MREG 0x0008 /* 1=Multiple register access (MII mgt) */ #define PHY_CFG2_INTMDIO 0x0004 /* 1=Interrupt signaled with MDIO pulseo */ /* PHY Status Output (and Interrupt status) Register */ #define PHY_INT_REG 0x12 /* Status Output (Interrupt Status) */ #define PHY_INT_INT 0x8000 /* 1=bits have changed since last read */ #define PHY_INT_LNKFAIL 0x4000 /* 1=Link Not detected */ #define PHY_INT_LOSSSYNC 0x2000 /* 1=Descrambler has lost sync */ #define PHY_INT_CWRD 0x1000 /* 1=Invalid 4B5B code detected on rx */ #define PHY_INT_SSD 0x0800 /* 1=No Start Of Stream detected on rx */ #define PHY_INT_ESD 0x0400 /* 1=No End Of Stream detected on rx */ #define PHY_INT_RPOL 0x0200 /* 1=Reverse Polarity detected */ #define PHY_INT_JAB 0x0100 /* 1=Jabber detected */ #define PHY_INT_SPDDET 0x0080 /* 1=100Base-TX mode, 0=10Base-T mode */ #define PHY_INT_DPLXDET 0x0040 /* 1=Device in Full Duplex */ /* PHY Interrupt/Status Mask Register */ #define PHY_MASK_REG 0x13 /* Interrupt Mask */ /* Uses the same bit definitions as PHY_INT_REG */ #endif /* __DRIVERS_NET_LAN91C111_H */