/****************************************************************************
 * include/nuttx/leds/ncp5623c.h
 *
 * Licensed to the Apache Software Foundation (ASF) under one or more
 * contributor license agreements.  See the NOTICE file distributed with
 * this work for additional information regarding copyright ownership.  The
 * ASF licenses this file to you under the Apache License, Version 2.0 (the
 * "License"); you may not use this file except in compliance with the
 * License.  You may obtain a copy of the License at
 *
 *   http://www.apache.org/licenses/LICENSE-2.0
 *
 * Unless required by applicable law or agreed to in writing, software
 * distributed under the License is distributed on an "AS IS" BASIS, WITHOUT
 * WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.  See the
 * License for the specific language governing permissions and limitations
 * under the License.
 *
 ****************************************************************************/

#ifndef __INCLUDE_NUTTX_LEDS_NCP5623C_H
#define __INCLUDE_NUTTX_LEDS_NCP5623C_H

/****************************************************************************
 * Included Files
 ****************************************************************************/

#include <nuttx/config.h>
#include <nuttx/fs/ioctl.h>

/* Configuration
 * CONFIG_I2C - Enables support for I2C drivers
 * CONFIG_NCP5623C - Enables support for the NCP5623C driver
 */

#if defined(CONFIG_I2C) && defined(CONFIG_NCP5623C)

/****************************************************************************
 * Pre-processor Definitions
 ****************************************************************************/

/* I2C definitions */

#define I2C_BUS_FREQ_HZ        (400000)

/* NCP5623C register addresses */

#define NCP5623C_SHUTDOWN      (0x00)     /* System Shut Down */
#define NCP5623C_ILED          (0x1)      /* ILED current */
#define NCP5623C_PWM1          (0x2)      /* LED 1 brightness control */
#define NCP5623C_PWM2          (0x3)      /* LED 2 brightness control */
#define NCP5623C_PWM3          (0x4)      /* LED 3 brightness control */
#define NCP5623C_UPWARD        (0x5)      /* Set Up the IEND Upward */
#define NCP5623C_DWNWRD        (0x6)      /* Set Up the IEND Downward */
#define NCP5623C_GRAD          (0x7)      /* Set Up the Gradual Dimming */
#define NCP5623C_MAX_REG       (0x7)      /* Highest register */

#define NCP5623C_ADDRESS_MASK  (0xe0)     /* Address part of reg */
#define NCP5623C_VALUE_MASK    (0x1f)     /* Value part of reg */
#define NCP5623C_SHIFT_ADDRESS (5)
#define NCP5623C_MAX_VALUE     (0x1f)     /* Max value of all registers */

#define NCP5623C_SET_REG(addr, val) \
  (((addr << NCP5623C_SHIFT_ADDRESS) & NCP5623C_ADDRESS_MASK) | \
   (val & NCP5623C_VALUE_MASK))           /* combine addr and val */

/* IOCTL commands */

#define LEDIOC_SET_REG _ULEDIOC(1)        /* Arg: ncp5623c_set_reg_s * pointer */

/****************************************************************************
 * Public Types
 ****************************************************************************/

enum led_select_e
{
  LED_1 = NCP5623C_PWM1,
  LED_2 = NCP5623C_PWM2,
  LED_3 = NCP5623C_PWM3
};

/* This structure is used in an IOCTL command for setting the PWM of an
 * individual LED. The desired LED is selected by setting the 'led' parameter
 * accordingly whereas the 'led_pwm' field governs the brightness of the
 * selected LED. A value of 0 (0x00) leads to a duty cycle of 0 % = LED off
 * while a value of 255 (0xFF) leads to a duty cycle of 99.6 % = Maximum
 * brightness.
 */

struct ncp5623c_set_reg_s
{
  uint8_t reg;
  uint8_t val;
};

/****************************************************************************
 * Forward declarations
 ****************************************************************************/

struct i2c_master_s;

/****************************************************************************
 * Public Types
 ****************************************************************************/

#ifdef __cplusplus
#define EXTERN extern "C"
extern "C"
{
#else
#define EXTERN extern
#endif

/****************************************************************************
 * Name: ncp5623c_register
 *
 * Description:
 *   Register the NCP5623C device as 'devpath'
 *
 * Input Parameters:
 *   devpath - The full path to the driver to register. E.g., "/dev/leddrv0".
 *   i2c     - An instance of the I2C interface to use to communicate
 *             with the LM92.
 *   ncp5623c_i2c_addr
 *           - The I2C address of the NCP5623C.
 *
 * Returned Value:
 *   Zero (OK) on success; a negated errno value on failure.
 *
 ****************************************************************************/

int ncp5623c_register(FAR const char *devpath, FAR struct i2c_master_s *i2c,
                      uint8_t const ncp5623c_i2c_addr);

#undef EXTERN
#ifdef __cplusplus
}
#endif

#endif /* CONFIG_I2C && CONFIG_I2C_NCP5623C */
#endif /* __INCLUDE_NUTTX_LEDS_NCP5623C_H */