#
# For a description of the syntax of this configuration file,
# see the file kconfig-language.txt in the NuttX tools repository.
#

menu "IEEE 802.15.4 socket support"

config NET_IEEE802154
	bool "IEEE 802.15.4 socket support"
	default n
	depends on WIRELESS_IEEE802154
	select NETDEV_IOCTL
	---help---
		Enable support for raw, IEEE 802.15.4 sockets.

		Raw sockets allow receiving and transmitting IEEE 802.15.4 radio
		frames without a layer2 protocol such as 6LoWPAN in between. Frames
		received are copied into a IEEE 802.15.4 socket tap before they
		enter the network. Frames written into a IEEE 802.15.4 socket will
		bypass the network altogether and will be sent directly to the
		IEEE 802.15.4 MAC network interface driver outgoing frame queue.

if NET_IEEE802154

config NET_IEEE802154_FRAMELEN
	int "IEEE 802.15.4 Frame Length"
	default 127
	range 1 999999
	---help---
		For standard IEEE 802.15.4 radios, this should always be 127 bytes.
		However, some IEEE 802.15.4 radios may non-standard frame lengths.

		This setting is currently used only for detection data transfers
		that would exceed the radio frame length.

config NET_IEEE802154_PREALLOC_CONNS
	int "Preallocated IEEE 802.15.4 sockets"
	default 4
	---help---
		Number of IEEE 802.15.4 connections (all tasks).

		This number of connections will be pre-allocated during system boot.
		If dynamic connections allocation is enabled, more connections may
		be allocated at a later time, as the system needs them. Else this
		will be the maximum number of connections available to the system
		at all times.

		Set to 0 to disable (and rely only on dynamic allocations).

config NET_IEEE802154_ALLOC_CONNS
	int "Dynamic IEEE 802.15.4 connections allocation"
	default 0
	---help---
		Dynamic memory allocations for IEEE 802.15.4.

		When set to 0 all dynamic allocations are disabled.

		When set to 1 a new connection will be allocated every time,
		and it will be free'd when no longer needed.

		Setting this to 2 or more will allocate the connections in
		batches (with batch size equal to this config). When a
		connection is no longer needed, it will be returned to the
		free connections pool, and it will never be deallocated!

config NET_IEEE802154_MAX_CONNS
	int "Maximum number of IEEE 802.15.4 connections"
	default 0
	depends on NET_IEEE802154_ALLOC_CONNS > 0
	---help---
		If dynamic connections allocation is selected (NET_IEEE802154_ALLOC_CONNS > 0)
		this will limit the number of connections that can be allocated.

		This is useful in case the system is under very heavy load (or
		under attack), ensuring that the heap will not be exhausted.

config NET_IEEE802154_NCONTAINERS
	int "Number of pre-allocated frame containers"
	default 8
	---help---
		This specifies the total number of preallocated frame containers.
		One must be allocated with each incoming frame.

config NET_IEEE802154_BACKLOG
	int "Maximum frame backlog"
	default 8
	range 0 255
	---help---
		As frames are received, then are help in an RX queue.  They remain
		in the RX queue until application logic reads the queue frames.  To
		prevent overrun, the maximum backlog may be set to a nonzero value.
		What the backlog of queue frames reaches that count, the olds frame
		will be freed, preventing overrun at the cost of losing the oldest
		frames.

		NOTE: The special value of zero will disable all backlog checks.

endif # NET_IEEE802154
endmenu # IEEE 802.15.4 Socket Support