/**************************************************************************** * drivers/lcd/ft80x.c * * Licensed to the Apache Software Foundation (ASF) under one or more * contributor license agreements. See the NOTICE file distributed with * this work for additional information regarding copyright ownership. The * ASF licenses this file to you under the Apache License, Version 2.0 (the * "License"); you may not use this file except in compliance with the * License. You may obtain a copy of the License at * * http://www.apache.org/licenses/LICENSE-2.0 * * Unless required by applicable law or agreed to in writing, software * distributed under the License is distributed on an "AS IS" BASIS, WITHOUT * WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. See the * License for the specific language governing permissions and limitations * under the License. * ****************************************************************************/ /* References: * - Document No.: FT_000792, "FT800 Embedded Video Engine", Datasheet * Version 1.1, Clearance No.: FTDI# 334, Future Technology Devices * International Ltd. * - Document No.: FT_000986, "FT801 Embedded Video Engine Datasheet", * Version 1.0, Clearance No.: FTDI#376, Future Technology Devices * International Ltd. * - Application Note AN_240AN_240, "FT800 From the Ground Up", Version * 1.1, Issue Date: 2014-06-09, Future Technology Devices International * Ltd. * - "FT800 Series Programmer Guide Guide", Version 2.1, Issue Date: * 2016-09-19, Future Technology Devices International Ltd. */ /**************************************************************************** * Included Files ****************************************************************************/ #include #include #include #include #include #include #include #include #include #include #include #include #include #include #include #include #include #include #include #include "ft80x.h" #ifdef CONFIG_LCD_FT80X /**************************************************************************** * Pre-processor Definitions ****************************************************************************/ #define CHIPID 0x7c #define ROMID_MASK 0x0000ffff #define VERSION_MASK 0xffff0000 #if defined(CONFIG_LCD_FT800) # define DEVNAME "/dev/ft800" # define ROM_CHIPID 0x00010008 /* Byte [0:1] Chip ID "0800" BCD * Byte [2:3] Version "0100" BCD */ #elif defined(CONFIG_LCD_FT801) # define DEVNAME "/dev/ft801" # define ROM_CHIPID 0x00010108 /* Byte [0:1] Chip ID "0801" BCD * Byte [2:3] Version "0100" BCD */ #else # error No FT80x device configured #endif #define ROMID (ROM_CHIPID & ROMID_MASK) #define VERSION (ROM_CHIPID & VERSION_MASK) #define MIN_FADE_DELAY 10 /* Milliseconds */ #define MAX_FADE_DELAY 16700 /* Milliseconds */ #define FADE_STEP_MSEC 10 /* Milliseconds */ /**************************************************************************** * Private Function Prototypes ****************************************************************************/ static int ft80x_fade(FAR struct ft80x_dev_s *priv, FAR const struct ft80x_fade_s *fade); static void ft80x_notify(FAR struct ft80x_dev_s *priv, enum ft80x_notify_e id, int value); static void ft80x_interrupt_work(FAR void *arg); static int ft80x_interrupt(int irq, FAR void *context, FAR void *arg); #ifndef CONFIG_DISABLE_PSEUDOFS_OPERATIONS static void ft80x_destroy(FAR struct ft80x_dev_s *priv); #endif /* Character driver methods */ static int ft80x_open(FAR struct file *filep); static int ft80x_close(FAR struct file *filep); static ssize_t ft80x_read(FAR struct file *filep, FAR char *buffer, size_t buflen); static ssize_t ft80x_write(FAR struct file *filep, FAR const char *buffer, size_t buflen); static int ft80x_ioctl(FAR struct file *filep, int cmd, unsigned long arg); #ifndef CONFIG_DISABLE_PSEUDOFS_OPERATIONS static int ft80x_unlink(FAR struct inode *inode); #endif /* Initialization */ static int ft80x_initialize(FAR struct ft80x_dev_s *priv); /**************************************************************************** * Private Data ****************************************************************************/ static const struct file_operations g_ft80x_fops = { ft80x_open, /* open */ ft80x_close, /* close */ ft80x_read, /* read */ ft80x_write, /* write */ NULL, /* seek */ ft80x_ioctl, /* ioctl */ NULL, /* mmap */ NULL, /* truncate */ NULL /* poll */ #ifndef CONFIG_DISABLE_PSEUDOFS_OPERATIONS , ft80x_unlink /* unlink */ #endif }; /**************************************************************************** * Private Functions ****************************************************************************/ /**************************************************************************** * Name: ft80x_fade * * Description: * Change the backlight intensity with a controllable fade. * ****************************************************************************/ static int ft80x_fade(FAR struct ft80x_dev_s *priv, FAR const struct ft80x_fade_s *fade) { clock_t start; clock_t elapsed; int32_t delay; int32_t duty; int16_t endduty; int16_t delta; /* 0% corresponds to the value 0, but 100% corresponds to the value 128 */ endduty = (uint16_t)((uint16_t)fade->duty << 7) / 100; /* Get the change in duty from the current to the terminal duty. */ duty = (int32_t)(ft80x_read_byte(priv, FT80X_REG_PWM_DUTY) & 0x7f); delta = endduty - (int16_t)duty; /* The "smoothness" of the steps will depend on the resolution of the * system timer. The minimum delay is <= 2 * system_clock_period. * * We will try for a FADE_STEP_MSEC delay, but we will try to adapt to * whatever we get is we are working close the system time resolution. * For human factors reasons, any delay less than 100 MS or so should * appear more or less smooth. * * The delay calculation should never overflow: * * Max delay: 16,700 msec (MAX_FADE_DELAY) * Min clock period: 1 usec * Max delay: 16,700,000 ticks * INT32_MAX 2,147,483,647 */ delay = MSEC2TICK((int32_t)fade->delay); if (delay <= 0) { delay = 1; } start = clock_systime_ticks(); do { /* Wait for FADE_STEP_MSEC msec (or whatever we get) */ nxsig_usleep(FADE_STEP_MSEC * 1000); /* Get the elapsed time */ elapsed = clock_systime_ticks() - start; if (elapsed > INT32_MAX || (int32_t)elapsed >= delay) { duty = endduty; } else { /* Interpolate to get the next PWM duty in the fade. This * calculation should never overflow: * * Max delta: 128 * Max elapsed: 16,700,000 ticks * Max numerator: 2,137,600,000 * Min denominator: 1 * Max duty: 2,137,600,000 * INT32_MAX 2,147,483,647 */ duty += ((int32_t)delta * (int32_t)elapsed) / delay; if (duty > 128) { duty = 128; } else if (duty < 0) { duty = 0; } } /* The set the new backlight PWM duty */ ft80x_write_byte(priv, FT80X_REG_PWM_DUTY, (uint8_t)duty); } while (duty != endduty); return OK; } /**************************************************************************** * Name: ft80x_notify * * Description: * Notify any registered client of the FT80x event * ****************************************************************************/ static void ft80x_notify(FAR struct ft80x_dev_s *priv, enum ft80x_notify_e id, int value) { FAR struct ft80x_eventinfo_s *info = &priv->notify[id]; /* Are notifications enabled for this event? */ if (info->enable) { DEBUGASSERT(info->pid > 0); /* Yes.. Signal the client */ info->event.sigev_value.sival_int = value; nxsig_notification(info->pid, &info->event, SI_QUEUE, &info->work); } } /**************************************************************************** * Name: ft80x_interrupt_work * * Description: * Back end handling for FT80x interrupts * ****************************************************************************/ static void ft80x_interrupt_work(FAR void *arg) { FAR struct ft80x_dev_s *priv = (FAR struct ft80x_dev_s *)arg; uint32_t intflags; uint32_t regval; DEBUGASSERT(priv != NULL); /* Get exclusive access to the device structures */ nxmutex_lock(&priv->lock); /* Get the set of pending interrupts. Note that simply reading this * register is sufficient to clear all pending interrupts. */ intflags = ft80x_read_word(priv, FT80X_REG_INT_FLAGS); /* And process each pending interrupt. * * REVISIT: No interrupt sources are ever enabled in the current * implementation. */ if ((intflags & FT80X_INT_SWAP) != 0) { /* Display swap occurred */ lcdinfo("Display swap occurred\n"); ft80x_notify(priv, FT80X_NOTIFY_SWAP, 0); } if ((intflags & FT80X_INT_TOUCH) != 0) { /* Touch-screen touch detected */ lcdinfo("Touch-screen touch detected\n"); ft80x_notify(priv, FT80X_NOTIFY_TOUCH, 0); } if ((intflags & FT80X_INT_TAG) != 0) { /* Touch-screen tag value change */ lcdinfo("Touch-screen tag value change\n"); #ifdef CONFIG_LCD_FT800 regval = ft80x_read_word(priv, FT80X_REG_TOUCH_TAG); #else regval = ft80x_read_word(priv, FT80X_REG_CTOUCH_TAG); #endif ft80x_notify(priv, FT80X_NOTIFY_TAG, (int)(regval & TOUCH_TAG_MASK)); } if ((intflags & FT80X_INT_SOUND) != 0) { /* Sound effect ended */ lcdinfo(" Sound effect ended\n"); ft80x_notify(priv, FT80X_NOTIFY_SOUND, 0); } if ((intflags & FT80X_INT_PLAYBACK) != 0) { /* Audio playback ended */ lcdinfo("Audio playback ended\n"); ft80x_notify(priv, FT80X_NOTIFY_PLAYBACK, 0); } if ((intflags & FT80X_INT_CMDEMPTY) != 0) { /* Command FIFO empty */ lcdinfo("Command FIFO empty\n"); ft80x_notify(priv, FT80X_NOTIFY_CMDEMPTY, 0); } if ((intflags & FT80X_INT_CMDFLAG) != 0) { /* Command FIFO flag */ lcdinfo("Command FIFO flag\n"); ft80x_notify(priv, FT80X_NOTIFY_CMDFLAG, 0); } if ((intflags & FT80X_INT_CONVCOMPLETE) != 0) { /* Touch-screen conversions completed */ lcdinfo(" Touch-screen conversions completed\n"); ft80x_notify(priv, FT80X_NOTIFY_CONVCOMPLETE, 0); } /* Re-enable interrupts */ DEBUGASSERT(priv->lower != NULL && priv->lower->enable != NULL); priv->lower->enable(priv->lower, true); nxmutex_unlock(&priv->lock); } /**************************************************************************** * Name: ft80x_interrupt * * Description: * FT80x interrupt handler * ****************************************************************************/ static int ft80x_interrupt(int irq, FAR void *context, FAR void *arg) { FAR struct ft80x_dev_s *priv = (FAR struct ft80x_dev_s *)arg; DEBUGASSERT(priv != NULL); /* Perform the interrupt work on the high priority work queue. */ work_queue(HPWORK, &priv->intwork, ft80x_interrupt_work, priv, 0); /* Disable further interrupts for the GPIO interrupt source. * REVISIT: This assumes that GPIO interrupts will pend until re-enabled. * In certain implementations, that assumption is not true and could cause * a loss of interrupts. */ DEBUGASSERT(priv->lower != NULL && priv->lower->enable != NULL); priv->lower->enable(priv->lower, false); return OK; } /**************************************************************************** * Name: ft80x_destroy * * Description: * The driver has been unlinked... clean up as best we can. * ****************************************************************************/ #ifndef CONFIG_DISABLE_PSEUDOFS_OPERATIONS static void ft80x_destroy(FAR struct ft80x_dev_s *priv) { /* If the lower half driver provided a destroy method, then call that * method now in order order to clean up resources used by the lower-half * driver. */ DEBUGASSERT(priv != NULL && priv->lower != NULL); if (priv->lower->destroy != NULL) { priv->lower->destroy(priv->lower); } /* Then free our container */ nxmutex_destroy(&priv->lock); kmm_free(priv); } #endif /**************************************************************************** * Name: ft80x_open * * Description: * This function is called whenever the PWM device is opened. * ****************************************************************************/ static int ft80x_open(FAR struct file *filep) { #ifndef CONFIG_DISABLE_PSEUDOFS_OPERATIONS FAR struct inode *inode; FAR struct ft80x_dev_s *priv; uint8_t tmp; int ret; inode = filep->f_inode; DEBUGASSERT(inode->i_private != NULL); priv = inode->i_private; lcdinfo("crefs: %d\n", priv->crefs); /* Get exclusive access to the device structures */ ret = nxmutex_lock(&priv->lock); if (ret < 0) { goto errout; } /* Increment the count of references to the device */ tmp = priv->crefs + 1; if (tmp == 0) { /* More than 255 opens; uint8_t overflows to zero */ ret = -EMFILE; goto errout_with_lock; } /* Save the new open count */ priv->crefs = tmp; ret = OK; errout_with_lock: nxmutex_unlock(&priv->lock); errout: return ret; #else return OK; #endif } /**************************************************************************** * Name: ft80x_close * * Description: * This function is called when the PWM device is closed. * ****************************************************************************/ static int ft80x_close(FAR struct file *filep) { #ifndef CONFIG_DISABLE_PSEUDOFS_OPERATIONS FAR struct inode *inode; FAR struct ft80x_dev_s *priv; int ret; inode = filep->f_inode; DEBUGASSERT(inode->i_private != NULL); priv = inode->i_private; lcdinfo("crefs: %d\n", priv->crefs); /* Get exclusive access to the device structures */ ret = nxmutex_lock(&priv->lock); if (ret < 0) { goto errout; } /* Will the count decrement to zero? */ if (priv->crefs <= 1) { /* Yes.. if the driver has been unlinked, then we need to destroy the * driver instance. */ priv->crefs = 0; if (priv->unlinked) { nxmutex_unlock(&priv->lock); ft80x_destroy(priv); return OK; } } else { /* NO.. decrement the number of references to the driver. */ priv->crefs--; } ret = OK; nxmutex_unlock(&priv->lock); errout: return ret; #else return OK; #endif } /**************************************************************************** * Name: ft80x_read ****************************************************************************/ static ssize_t ft80x_read(FAR struct file *filep, FAR char *buffer, size_t len) { /* Reading from the FT80X is an undefined operation and not support */ lcdinfo("buffer: %p len %lu\n", buffer, (unsigned long)len); return 0; /* Return EOF */ } /**************************************************************************** * Name: ft80x_write ****************************************************************************/ static ssize_t ft80x_write(FAR struct file *filep, FAR const char *buffer, size_t len) { FAR struct inode *inode; FAR struct ft80x_dev_s *priv; int ret; lcdinfo("buffer: %p len %lu\n", buffer, (unsigned long)len); DEBUGASSERT(buffer != NULL && ((uintptr_t)buffer & 3) == 0 && len > 0 && (len & 3) == 0 && len <= FT80X_RAM_DL_SIZE); inode = filep->f_inode; DEBUGASSERT(inode->i_private != NULL); priv = inode->i_private; if (buffer == NULL || ((uintptr_t)buffer & 3) != 0 || len == 0 || (len & 3) != 0 || (len + filep->f_pos) > FT80X_RAM_DL_SIZE) { return -EINVAL; } /* Get exclusive access to the device structures */ ret = nxmutex_lock(&priv->lock); if (ret < 0) { return ret; } /* Note that there is no check if the driver was opened read-only. That * would be a silly thing to do. */ /* The write method is functionally equivalent to the FT80X_IOC_CREATEDL * IOCTL command: It simply copies the display list in the user buffer to * the FT80x display list memory. */ ft80x_write_memory(priv, FT80X_RAM_DL + filep->f_pos, buffer, len); filep->f_pos += len; nxmutex_unlock(&priv->lock); return len; } /**************************************************************************** * Name: ft80x_ioctl * * Description: * The standard ioctl method. This is where ALL of the PWM work is done. * ****************************************************************************/ static int ft80x_ioctl(FAR struct file *filep, int cmd, unsigned long arg) { FAR struct inode *inode; FAR struct ft80x_dev_s *priv; int ret; inode = filep->f_inode; DEBUGASSERT(inode->i_private != NULL); priv = inode->i_private; lcdinfo("cmd: %d arg: %lu\n", cmd, arg); /* Get exclusive access to the device structures */ ret = nxmutex_lock(&priv->lock); if (ret < 0) { return ret; } /* Handle built-in ioctl commands */ switch (cmd) { /* FT80X_IOC_CREATEDL: * Description: Write a display list to the FT80x display list * memory * Description: Write a display list to the FT80x display list * memory starting at offset zero. This may or may * not be the entire display list. Display lists may * be created incrementally, starting with * FT80X_IOC_CREATEDL and finishing the display list * using FT80XIO_APPENDDL * Argument: A reference to a display list structure instance. * See struct ft80x_displaylist_s. * Returns: None */ case FT80X_IOC_CREATEDL: /* Set the file position to zero and fall through to "append" the new * display list data at offset 0. */ filep->f_pos = 0; /* FALLTHROUGH */ /* FT80X_IOC_APPENDDL: * Description: Write additional display list entries to the FT80x * display list memory at the current display list * offset. This IOCTL command permits display lists * to be completed incrementally, starting with * FT80X_IOC_CREATEDL and finishing the display list * using FT80XIO_APPENDDL. * Argument: A reference to a display list structure instance. * See struct ft80x_displaylist_s. * Returns: None */ case FT80X_IOC_APPENDDL: { FAR struct ft80x_displaylist_s *dl = (FAR struct ft80x_displaylist_s *)((uintptr_t)arg); if (dl == NULL || ((uintptr_t)&dl->cmd & 3) != 0 || (dl->dlsize & 3) != 0 || dl->dlsize + filep->f_pos > FT80X_RAM_DL_SIZE) { ret = -EINVAL; } else { /* Check if there is a display list. It might be useful for * the application to issue FT80X_IOC_CREATEDL with no data in * order to initialize the display list, then form all of the * list entries with FT80X_IOC_APPENDDL. */ if (dl->dlsize > 0) { /* This IOCTL command simply copies the display list * provided into the FT80x display list memory. */ ft80x_write_memory(priv, FT80X_RAM_DL + filep->f_pos, &dl->cmd, dl->dlsize); filep->f_pos += dl->dlsize; } ret = OK; } } break; /* FT80X_IOC_GETRAMDL: * Description: Read a 32-bit value from the display list. * Argument: A reference to an instance of struct ft80x_relmem_s. * Returns: The 32-bit value read from the display list. */ case FT80X_IOC_GETRAMDL: { FAR struct ft80x_relmem_s *ramdl = (FAR struct ft80x_relmem_s *)((uintptr_t)arg); if (ramdl == NULL || ((uintptr_t)ramdl->offset & 3) != 0 || ramdl->offset >= FT80X_RAM_DL_SIZE) { ret = -EINVAL; } else { ft80x_read_memory(priv, FT80X_RAM_DL + ramdl->offset, ramdl->value, ramdl->nbytes); ret = OK; } } break; /* FT80X_IOC_PUTRAMG * Description: Write byte data to FT80x graphics memory (RAM_G) * Argument: A reference to an instance of struct ft80x_relmem_s. * Returns: None. */ case FT80X_IOC_PUTRAMG: { FAR struct ft80x_relmem_s *ramg = (FAR struct ft80x_relmem_s *)((uintptr_t)arg); if (ramg == NULL || (ramg->offset + ramg->nbytes) >= FT80X_RAM_G_SIZE) { ret = -EINVAL; } else { ft80x_write_memory(priv, FT80X_RAM_G + ramg->offset, ramg->value, ramg->nbytes); ret = OK; } } break; /* FT80X_IOC_PUTRAMCMD * Description: Write 32-bit aligned data to FT80x FIFO (RAM_CMD) * Argument: A reference to an instance of struct ft80x_relmem_s. * Returns: None. */ case FT80X_IOC_PUTRAMCMD: { FAR struct ft80x_relmem_s *ramcmd = (FAR struct ft80x_relmem_s *)((uintptr_t)arg); if (ramcmd == NULL || ((uintptr_t)ramcmd->offset & 3) != 0) { ret = -EINVAL; } else { ft80x_write_memory(priv, FT80X_RAM_CMD + ramcmd->offset, ramcmd->value, ramcmd->nbytes); ret = OK; } } break; /* FT80X_IOC_GETREG8: * Description: Read an 8-bit register value from the FT80x. * Argument: A reference to an instance of struct * ft80x_register_s. * Returns: The 8-bit value read from the register. */ case FT80X_IOC_GETREG8: { FAR struct ft80x_register_s *reg = (FAR struct ft80x_register_s *)((uintptr_t)arg); if (reg == NULL || ((uintptr_t)reg->addr & 3) != 0) { ret = -EINVAL; } else { reg->value.u8 = ft80x_read_byte(priv, reg->addr); ret = OK; } } break; /* FT80X_IOC_GETREG16: * Description: Read a 16-bit register value from the FT80x. * Argument: A reference to an instance of struct * ft80x_register_s. * Returns: The 16-bit value read from the register. */ case FT80X_IOC_GETREG16: { FAR struct ft80x_register_s *reg = (FAR struct ft80x_register_s *)((uintptr_t)arg); if (reg == NULL || ((uintptr_t)reg->addr & 3) != 0) { ret = -EINVAL; } else { reg->value.u16 = ft80x_read_hword(priv, reg->addr); ret = OK; } } break; /* FT80X_IOC_GETREG32: * Description: Read a 32-bit register value from the FT80x. * Argument: A reference to an instance of struct * ft80x_register_s. * Returns: The 32-bit value read from the register. */ case FT80X_IOC_GETREG32: { FAR struct ft80x_register_s *reg = (FAR struct ft80x_register_s *)((uintptr_t)arg); if (reg == NULL || ((uintptr_t)reg->addr & 3) != 0) { ret = -EINVAL; } else { reg->value.u32 = ft80x_read_word(priv, reg->addr); ret = OK; } } break; /* FT80X_IOC_GETREGS: * Description: Read multiple 32-bit register values from the FT80x. * Argument: A reference to an instance of struct * ft80x_registers_s. * Returns: The 32-bit values read from the consecutive * registers . */ case FT80X_IOC_GETREGS: { FAR struct ft80x_registers_s *regs = (FAR struct ft80x_registers_s *)((uintptr_t)arg); if (regs == NULL || ((uintptr_t)regs->addr & 3) != 0) { ret = -EINVAL; } else { ft80x_read_memory(priv, regs->addr, regs->value, (size_t)regs->nregs << 2); ret = OK; } } break; /* FT80X_IOC_PUTREG8: * Description: Write an 8-bit register value to the FT80x. * Argument: A reference to an instance of struct * ft80x_register_s. * Returns: None. */ case FT80X_IOC_PUTREG8: { FAR struct ft80x_register_s *reg = (FAR struct ft80x_register_s *)((uintptr_t)arg); if (reg == NULL || ((uintptr_t)reg->addr & 3) != 0) { ret = -EINVAL; } else { ft80x_write_byte(priv, reg->addr, reg->value.u8); ret = OK; } } break; /* FT80X_IOC_PUTREG16: * Description: Write a 16-bit register value to the FT80x. * Argument: A reference to an instance of struct * ft80x_register_s. * Returns: None. */ case FT80X_IOC_PUTREG16: { FAR struct ft80x_register_s *reg = (FAR struct ft80x_register_s *)((uintptr_t)arg); if (reg == NULL || ((uintptr_t)reg->addr & 3) != 0) { ret = -EINVAL; } else { ft80x_write_hword(priv, reg->addr, reg->value.u16); ret = OK; } } break; /* FT80X_IOC_PUTREG32: * Description: Write a 32-bit register value to the FT80x. * Argument: A reference to an instance of struct * ft80x_register_s. * Returns: None. */ case FT80X_IOC_PUTREG32: { FAR struct ft80x_register_s *reg = (FAR struct ft80x_register_s *)((uintptr_t)arg); if (reg == NULL || ((uintptr_t)reg->addr & 3) != 0) { ret = -EINVAL; } else { ft80x_write_word(priv, reg->addr, reg->value.u32); ret = OK; } } break; /* FT80X_IOC_PUTREGS: * Description: Write multiple 32-bit register values to the FT80x. * Argument: A reference to an instance of struct * ft80x_registers_s. * Returns: None. */ case FT80X_IOC_PUTREGS: { FAR struct ft80x_registers_s *regs = (FAR struct ft80x_registers_s *)((uintptr_t)arg); if (regs == NULL || ((uintptr_t)regs->addr & 3) != 0) { ret = -EINVAL; } else { ft80x_write_memory(priv, regs->addr, regs->value, (size_t)regs->nregs << 2); ret = OK; } } break; /* FT80X_IOC_EVENTNOTIFY: * Description: Setup to receive a signal when an event occurs. * Argument: A reference to an instance of struct ft80x_notify_s. * Returns: None */ case FT80X_IOC_EVENTNOTIFY: { FAR struct ft80x_notify_s *notify = (FAR struct ft80x_notify_s *)((uintptr_t)arg); if (notify == NULL || notify->pid < 0 || (unsigned int)notify->id >= FT80X_INT_NEVENTS) { ret = -EINVAL; } else { FAR struct ft80x_eventinfo_s *info = &priv->notify[notify->id]; uint32_t regval; /* Are we enabling or disabling */ if (notify->enable) { /* Make sure that arguments are valid for the enable */ if (notify->pid == 0) { ret = -EINVAL; } else { /* Setup the new notification information */ info->event = notify->event; info->pid = notify->pid; info->enable = true; /* Enable interrupts associated with the event */ regval = ft80x_read_word(priv, FT80X_REG_INT_MASK); regval |= (1 << notify->id); ft80x_write_word(priv, FT80X_REG_INT_MASK, regval); ret = OK; } } else { /* Disable the notification */ info->pid = 0; info->enable = false; /* Disable interrupts associated with the event */ regval = ft80x_read_word(priv, FT80X_REG_INT_MASK); regval &= ~(1 << notify->id); ft80x_write_word(priv, FT80X_REG_INT_MASK, regval); /* Cancel any pending notification */ nxsig_cancel_notification(&info->work); ret = OK; } } } break; /* FT80X_IOC_FADE: * Description: Change the backlight intensity with a controllable * fade. * Argument: A reference to an instance of struct ft80x_fade_s. * Returns: None. */ case FT80X_IOC_FADE: { FAR const struct ft80x_fade_s *fade = (FAR const struct ft80x_fade_s *)((uintptr_t)arg); if (fade == NULL || fade->duty > 100 || fade->delay < MIN_FADE_DELAY || fade->delay > MAX_FADE_DELAY) { ret = -EINVAL; } else { ret = ft80x_fade(priv, fade); } } break; /* FT80X_IOC_AUDIO: * Description: Enable/disable an external audio amplifier. * Argument: 0=disable; 1=enable. * Returns: None. */ case FT80X_IOC_AUDIO: { #if defined(CONFIG_LCD_FT80X_AUDIO_MCUSHUTDOWN) /* Amplifier is controlled by an MCU GPIO pin */ DEBUGASSERT(priv->lower->attach != NULL && priv->lower->audio != NULL); DEBUGASSERT(arg == 0 || arg == 1); priv->lower->audio(priv->lower, (arg != 0)); ret = OK; #elif defined(CONFIG_LCD_FT80X_AUDIO_GPIOSHUTDOWN) /* Amplifier is controlled by an FT80x GPIO pin */ uint8_t regval8; DEBUGASSERT(arg == 0 || arg == 1); regval8 = ft80x_read_byte(priv, FT80X_REG_GPIO); /* Active low logic assumed */ if (arg == 0) { regval8 |= (1 << CONFIG_LCD_FT80X_AUDIO_GPIO); } else { regval8 &= ~(1 << CONFIG_LCD_FT80X_AUDIO_GPIO); } ft80x_write_byte(priv, FT80X_REG_GPIO, regval8); ret = OK; #else /* Amplifier is not controllable. */ DEBUGASSERT(arg == 0 || arg == 1); return OK; #endif } break; /* Unrecognized IOCTL command */ default: lcderr("ERROR: Unrecognized cmd: %d arg: %ld\n", cmd, arg); ret = -ENOTTY; break; } nxmutex_unlock(&priv->lock); return ret; } /**************************************************************************** * Name: ft80x_unlink ****************************************************************************/ #ifndef CONFIG_DISABLE_PSEUDOFS_OPERATIONS static int ft80x_unlink(FAR struct inode *inode) { FAR struct ft80x_dev_s *priv; /* Get the reference to our internal state structure from the inode * structure. */ DEBUGASSERT(inode->i_private); priv = inode->i_private; /* Indicate that the driver has been unlinked */ priv->unlinked = true; /* If there are no further open references to the driver, then commit * Hara-Kiri now. */ if (priv->crefs == 0) { ft80x_destroy(priv); } return OK; } #endif /**************************************************************************** * Name: ft80x_initialize * * Description: * Initialize the FT80x * ****************************************************************************/ static int ft80x_initialize(FAR struct ft80x_dev_s *priv) { uint32_t timeout; uint32_t regval32; uint8_t regval8; /* To configure the display, load the timing control registers with values * for the particular display. These registers control horizontal timing: * * - FT80X_REG_PCLK * - FT80X_REG_PCLK_POL * - FT80X_REG_HCYCLE * - FT80X_REG_HOFFSET * - FT80X_REG_HSIZE * - FT80X_REG_HSYNC0 * - FT80X_REG_HSYNC1 * * These registers control vertical timing: * * - FT80X_REG_VCYCLE * - FT80X_REG_VOFFSET * - FT80X_REG_VSIZE * - FT80X_REG_VSYNC0 * - FT80X_REG_VSYNC1 * * And the FT80X_REG_CSPREAD register changes color clock timing to reduce * system noise. * * GPIO bit 7 is used for the display enable pin of the LCD module. By * setting the direction of the GPIO bit to out direction, the display can * be enabled by writing value of 1 into GPIO bit 7 or the display can be * disabled by writing a value of 0 into GPIO bit 7. By default GPIO bit 7 * direction is output and the value is 0. */ /* Initialization Sequence from Power Down using PD_N pin: * * 1. Drive the PD_N pin high * 2. Wait for at least 20ms * 3. Execute "Initialization Sequence during the Boot up" from steps 1 * to 9 * * Initialization Sequence from Sleep Mode: * * 1. Send Host command "ACTIVE" to enable clock to FT800 * 2. Wait for at least 20ms * 3. Execute "Initialization Sequence during Boot Up" from steps 5 to 8 * * Initialization sequence from standby mode: * * Execute all the steps mentioned in "Initialization Sequence from Sleep * Mode" except waiting for at least 20ms in step 2. */ DEBUGASSERT(priv->lower != NULL && priv->lower->pwrdown != NULL); priv->lower->pwrdown(priv->lower, false); up_mdelay(20); /* Initialization Sequence during the boot up: * * 1. Use MCU SPI clock not more than 11MHz * 2. Send Host command CLKEXT to FT800 to enable PLL input from oscillator * or external clock. Should default to 48MHz PLL output. * 3. Send Host command ACTIVE to enable clock and wake up the FT80x. * 4. Configure video timing registers, except FT80X_REG_PCLK * 5. Write first display list * 6. Write FT80X_REG_DLSWAP, FT800 swaps display list immediately * 7. Enable back light control for display * 8. Write FT80X_REG_PCLK, video output begins with the first display list * 9. Use MCU SPI clock not more than 30MHz */ /* 1. Select the initial SPI frequency */ DEBUGASSERT(priv->lower->init_frequency <= 11000000); priv->frequency = priv->lower->init_frequency; /* 2. Send Host command CLKEXT to FT800 to enable PLL input from oscillator * or external clock. */ ft80x_host_command(priv, FT80X_CMD_CLKEXT); up_mdelay(10); #if 0 /* Un-necessary? */ /* Switch PLL output to 48MHz (should be the default) */ ft80x_host_command(priv, FT80X_CMD_CLK48M); up_mdelay(10); #endif /* 3. Send Host command ACTIVE to enable clock and wake up the FT80x. */ ft80x_host_command(priv, FT80X_CMD_ACTIVE); up_mdelay(10); #if 0 /* Un-necessary? */ /* Do a core reset for safer */ ft80x_host_command(priv, FT80X_CMD_CORERST); #endif /* Verify the chip ID. Read repeatedly until FT80x is ready. */ timeout = 0; for (; ; ) { /* Read the Chip ID */ regval8 = ft80x_read_byte(priv, FT80X_REG_ID); if (regval8 == CHIPID) { /* Chip ID verify so FT80x is ready */ break; } /* Initial Chip ID read may fail because the chip is not yet ready. */ if (++timeout > 100000) { lcderr("ERROR: Bad chip ID: %02x\n", regval8); return -ENODEV; } } regval32 = ft80x_read_word(priv, FT80X_ROM_CHIPID); if ((regval32 & ROMID_MASK) != ROMID) { lcderr("ERROR: Bad ROM chip ID: %08lx\n", (unsigned long)regval32); return -ENODEV; } /* 4. Configure video timing registers, except FT80X_REG_PCLK * * Once the FT800 is awake and the internal clock set and Device ID * checked, the next task is to configure the LCD display parameters for * the chosen display with the values determined in Section 2.3.3 above. * * a. Set FT80X_REG_PCLK to zero - This disables the pixel clock output * while the LCD and other system parameters are configured * b. Set the following registers with values for the chosen display. * Typical WQVGA and QVGA values are shown: * * Register Description WQVGA QVGA * 480x272 320x240 * FT80X_REG_PCLK_POL Pixel Clock Polarity 1 0 * FT80X_REG_HSIZE Image width in pixels 480 320 * FT80X_REG_HCYCLE Total number of clocks per line 548 408 * FT80X_REG_HOFFSET Horizontal image start 43 70 * (pixels from left) * FT80X_REG_HSYNC0 Start of HSYNC pulse 0 0 * (falling edge) * FT80X_REG_HSYNC1 End of HSYNC pulse 41 10 * (rising edge) * FT80X_REG_VSIZE Image height in pixels 272 240 * FT80X_REG_VCYCLE Total number of lines per screen 292 263 * FT80X_REG_VOFFSET Vertical image start 12 13 * (lines from top) * FT80X_REG_VSYNC0 Start of VSYNC pulse 0 0 * (falling edge) * FT80X_REG_VSYNC1 End of VSYNC pulse 10 2 * (rising edge) * * c. Enable or disable FT80X_REG_CSPREAD with a value of 01h or 00h, * respectively. Enabling FT80X_REG_CSPREAD will offset the R, G and B * output bits so all they do not all change at the same time. */ ft80x_write_byte(priv, FT80X_REG_PCLK, 0); #if defined(CONFIG_LCD_FT80X_WQVGA) ft80x_write_hword(priv, FT80X_REG_HCYCLE, 548); ft80x_write_hword(priv, FT80X_REG_HOFFSET, 43); ft80x_write_hword(priv, FT80X_REG_HSYNC0, 0); ft80x_write_hword(priv, FT80X_REG_HSYNC1, 41); ft80x_write_hword(priv, FT80X_REG_VCYCLE, 292); ft80x_write_hword(priv, FT80X_REG_VOFFSET, 12); ft80x_write_hword(priv, FT80X_REG_VSYNC0, 0); ft80x_write_hword(priv, FT80X_REG_VSYNC1, 10); ft80x_write_byte(priv, FT80X_REG_SWIZZLE, 0); ft80x_write_byte(priv, FT80X_REG_PCLK_POL, 1); ft80x_write_byte(priv, FT80X_REG_CSPREAD, 1); ft80x_write_hword(priv, FT80X_REG_HSIZE, 480); ft80x_write_hword(priv, FT80X_REG_VSIZE, 272); #elif defined(CONFIG_LCD_FT80X_QVGA) ft80x_write_hword(priv, FT80X_REG_HCYCLE, 408); ft80x_write_hword(priv, FT80X_REG_HOFFSET, 70); ft80x_write_hword(priv, FT80X_REG_HSYNC0, 0); ft80x_write_hword(priv, FT80X_REG_HSYNC1, 10); ft80x_write_hword(priv, FT80X_REG_VCYCLE, 263); ft80x_write_hword(priv, FT80X_REG_VOFFSET, 13); ft80x_write_hword(priv, FT80X_REG_VSYNC0, 0); ft80x_write_hword(priv, FT80X_REG_VSYNC1, 2); ft80x_write_byte(priv, FT80X_REG_SWIZZLE, 2); ft80x_write_byte(priv, FT80X_REG_PCLK_POL, 0); ft80x_write_byte(priv, FT80X_REG_CSPREAD, 1); ft80x_write_hword(priv, FT80X_REG_HSIZE, 320); ft80x_write_hword(priv, FT80X_REG_VSIZE, 240); #else # error Unknown display size #endif /* 5. Write first display list */ ft80x_write_word(priv, FT80X_RAM_DL + 0, FT80X_CLEAR_COLOR_RGB(0, 0, 0)); ft80x_write_word(priv, FT80X_RAM_DL + 4, FT80X_CLEAR(1, 1, 1)); ft80x_write_word(priv, FT80X_RAM_DL + 8, FT80X_DISPLAY()); /* 6. Write FT80X_REG_DLSWAP, FT800 swaps display list immediately */ ft80x_write_byte(priv, FT80X_REG_DLSWAP, DLSWAP_FRAME); /* GPIO bit 7 is used for the display enable pin of the LCD module. By * setting the direction of the GPIO bit to out direction, the display can * be enabled by writing value of 1 into GPIO bit 7 or the display can be * disabled by writing a value of 0 into GPIO bit 7. By default GPIO bit 7 * direction is output and the value is 0. * * If an external audio amplified is controlled by an FT80x GPIO, then * configure that GPIO as well. Active low logic is assumed so that the * amplifier is initially in the shutdown state. */ regval8 = ft80x_read_byte(priv, FT80X_REG_GPIO_DIR); regval8 |= (1 << 7); #ifdef CONFIG_LCD_FT80X_AUDIO_GPIOSHUTDOWN regval8 |= (1 << CONFIG_LCD_FT80X_AUDIO_GPIO); #endif ft80x_write_byte(priv, FT80X_REG_GPIO_DIR, regval8); regval8 = ft80x_read_byte(priv, FT80X_REG_GPIO); regval8 |= (1 << 7); #ifdef CONFIG_LCD_FT80X_AUDIO_GPIOSHUTDOWN regval8 |= (1 << CONFIG_LCD_FT80X_AUDIO_GPIO); #endif ft80x_write_byte(priv, FT80X_REG_GPIO, regval8); /* 7. Enable back light control for display */ #warning Missing logic /* 8. Write FT80X_REG_PCLK, video output with the first display list */ #if defined(CONFIG_LCD_FT80X_WQVGA) ft80x_write_byte(priv, FT80X_REG_PCLK, 5); #elif defined(CONFIG_LCD_FT80X_QVGA) ft80x_write_byte(priv, FT80X_REG_PCLK, 8); #else # error Unknown display size #endif /* 9. Use MCU SPI clock not more than 30MHz */ DEBUGASSERT(priv->lower->op_frequency <= 30000000); priv->frequency = priv->lower->op_frequency; /* Configure touch mode. Using default touch mode of FRAME_SYNC (~60Hz) */ ft80x_write_byte(priv, FT80X_REG_TOUCH_MODE, TOUCH_MODE_FRAMESYNC); #if defined(CONFIG_LCD_FT800) /* Configure the touch threshold. The value 1200 may need to be tweaked * for your application. */ ft80x_write_hword(priv, FT80X_REG_TOUCH_RZTHRESH, 1200); #elif defined(CONFIG_LCD_FT801) #ifdef CONFIG_LCD_FT801_MULTITOUCH /* Selected extended mode */ ft80x_write_byte(priv, FT80X_REG_CTOUCH_EXTENDED, 0); #else /* Selected compatibility mode */ ft80x_write_byte(priv, FT80X_REG_CTOUCH_EXTENDED, 1); #endif #else # error No FT80x device configured #endif return OK; } /**************************************************************************** * Public Functions ****************************************************************************/ /**************************************************************************** * Name: ft80x_register * * Description: * Configure the ADS7843E to use the provided SPI device instance. This * will register the driver as /dev/ft800 or /dev/ft801, depending upon * the configuration. * * Input Parameters: * spi - An SPI driver instance * i2c - An I2C master driver instance * lower - Persistent board configuration data / lower half interface * * Returned Value: * Zero is returned on success. Otherwise, a negated errno value is * returned to indicate the nature of the failure. * ****************************************************************************/ #if defined(CONFIG_LCD_FT80X_SPI) int ft80x_register(FAR struct spi_dev_s *spi, FAR const struct ft80x_config_s *lower) #elif defined(CONFIG_LCD_FT80X_I2C) int ft80x_register(FAR struct i2c_master_s *i2c, FAR const struct ft80x_config_s *lower) #endif { FAR struct ft80x_dev_s *priv; int ret; #if defined(CONFIG_LCD_FT80X_SPI) DEBUGASSERT(spi != NULL && lower != NULL); #elif defined(CONFIG_LCD_FT80X_I2C) DEBUGASSERT(i2c != NULL && lower != NULL); #endif /* Allocate the driver state structure */ priv = kmm_zalloc(sizeof(struct ft80x_dev_s)); if (priv == NULL) { lcderr("ERROR: Failed to allocate state structure\n"); return -ENOMEM; } /* Save the lower level interface and configuration information */ priv->lower = lower; #ifdef CONFIG_LCD_FT80X_SPI /* Remember the SPI configuration */ priv->spi = spi; #else /* Remember the I2C configuration */ priv->i2c = i2c; #endif /* Initialize the mutual exclusion mutex */ nxmutex_init(&priv->lock); /* Initialize the FT80x */ ret = ft80x_initialize(priv); if (ret < 0) { goto errout_with_lock; } /* Attach our interrupt handler */ DEBUGASSERT(lower->attach != NULL && lower->enable != NULL); ret = lower->attach(lower, ft80x_interrupt, priv); if (ret < 0) { goto errout_with_lock; } /* Disable all interrupt sources, but enable interrupts both in the lower * half driver and in the FT80x. */ ft80x_write_word(priv, FT80X_REG_INT_MASK, 0); ft80x_write_word(priv, FT80X_REG_INT_EN, FT80X_INT_ENABLE); lower->enable(lower, true); /* Register the FT80x character driver */ ret = register_driver(DEVNAME, &g_ft80x_fops, 0666, priv); if (ret < 0) { goto errout_with_interrupts; } return OK; errout_with_interrupts: lower->enable(lower, false); ft80x_write_word(priv, FT80X_REG_INT_EN, FT80X_INT_DISABLE); lower->attach(lower, NULL, NULL); errout_with_lock: nxmutex_destroy(&priv->lock); kmm_free(priv); return ret; } #endif /* CONFIG_LCD_FT80X */