/**************************************************************************** * boards/arm/stm32wl5/nucleo-wl55jc/include/board.h * * Licensed to the Apache Software Foundation (ASF) under one or more * contributor license agreements. See the NOTICE file distributed with * this work for additional information regarding copyright ownership. The * ASF licenses this file to you under the Apache License, Version 2.0 (the * "License"); you may not use this file except in compliance with the * License. You may obtain a copy of the License at * * http://www.apache.org/licenses/LICENSE-2.0 * * Unless required by applicable law or agreed to in writing, software * distributed under the License is distributed on an "AS IS" BASIS, WITHOUT * WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. See the * License for the specific language governing permissions and limitations * under the License. * ****************************************************************************/ #ifndef __BOARDS_ARM_STM32WL5_NUCLEO_WL55JC_INCLUDE_BOARD_H #define __BOARDS_ARM_STM32WL5_NUCLEO_WL55JC_INCLUDE_BOARD_H /**************************************************************************** * Included Files ****************************************************************************/ #include #ifndef __ASSEMBLY__ # include #endif /* Clocking *****************************************************************/ /* nucleo-wl55jc has installed 32Mhz HSE oscillator */ #define STM32WL5_XTAL_FREQ 32000000ul /* Use the HSE */ #define STM32WL5_BOARD_USEHSE 1 /* HSE source is a TCXO crystal which needs to be first powered on */ #define STM32WL5_BOARD_USETCXO /* Prescaler common to all PLL inputs */ #define STM32WL5_PLLCFG_PLLM RCC_PLLCFG_PLLM(2) /* 32MHz / 2 = 16MHz */ /* 'main' PLL config; we use this to generate our system clock */ /* disable unused pll clocks */ #define STM32WL5_PLLCFG_PLLP 0 #undef STM32WL5_PLLCFG_PLLP_ENABLED #define STM32WL5_PLLCFG_PLLQ 0 #undef STM32WL5_PLLCFG_PLLQ_ENABLED /* further multiplicate source for system clock */ #define STM32WL5_PLLCFG_PLLN RCC_PLLCFG_PLLN(6) /* 16MHz * 6 = 96MHz */ #define STM32WL5_PLLCFG_PLLR RCC_PLLCFG_PLLR(2) /* 96MHz / 2 = 48MHz */ #define STM32WL5_PLLCFG_PLLR_ENABLED /* Resulting system clock is 48MHz */ #define STM32WL5_SYSCLK_FREQUENCY 48000000ul /* Configure the HCLK divisor (for the AHB bus, core, memory, and DMA */ #define STM32WL5_RCC_CFGR_HPRE RCC_CFGR_HPRE_SYSCLK /* HCLK = SYSCLK / 1 */ #define STM32WL5_HCLK_FREQUENCY STM32WL5_SYSCLK_FREQUENCY /* Configure the HCLK3 divisor (for flash and sram2) */ #define STM32WL5_RCC_CFGR_HPRE RCC_CFGR_HPRE_SYSCLK /* HCLK3 = SYSCLK / 1 */ #define STM32WL5_HCLK3_FREQUENCY STM32WL5_SYSCLK_FREQUENCY /* Configure the APB1 prescaler */ #define STM32WL5_RCC_CFGR_PPRE1 RCC_CFGR_PPRE1_HCLK /* PCLK1 = HCLK / 1 */ #define STM32WL5_PCLK1_FREQUENCY (STM32WL5_HCLK_FREQUENCY / 1) /* The timer clock frequencies are automatically defined by hardware. * If the APB prescaler equals 1, the timer clock frequencies are set to the * same frequency as that of the APB domain. Otherwise they are set to twice. */ #define STM32WL5_APB1_TIM2_CLKIN (STM32WL5_PCLK1_FREQUENCY) /* Configure the APB2 prescaler */ #define STM32WL5_RCC_CFGR_PPRE2 RCC_CFGR_PPRE2_HCLK /* PCLK2 = HCLK / 1 */ #define STM32WL5_PCLK2_FREQUENCY (STM32WL5_HCLK_FREQUENCY / 1) /* The timer clock frequencies are automatically defined by hardware. * If the APB prescaler equals 1, the timer clock frequencies are set to the * same frequency as that of the APB domain. Otherwise they are set to twice. */ #define STM32WL5_APB2_TIM1_CLKIN STM32WL5_PCLK2_FREQUENCY #define STM32WL5_APB2_TIM16_CLKIN STM32WL5_PCLK2_FREQUENCY #define STM32WL5_APB2_TIM17_CLKIN STM32WL5_PCLK2_FREQUENCY /* The timer clock frequencies are automatically defined by hardware. If the * APB prescaler equals 1, the timer clock frequencies are set to the same * frequency as that of the APB domain. Otherwise they are set to twice. * Note: TIM1,15,16 are on APB2, others on APB1 */ #define BOARD_TIM1_FREQUENCY STM32WL5_HCLK_FREQUENCY #define BOARD_TIM2_FREQUENCY STM32WL5_HCLK_FREQUENCY #define BOARD_TIM16_FREQUENCY STM32WL5_HCLK_FREQUENCY #define BOARD_TIM17_FREQUENCY STM32WL5_HCLK_FREQUENCY #define BOARD_LPTIM1_FREQUENCY STM32WL5_HCLK_FREQUENCY #define BOARD_LPTIM2_FREQUENCY STM32WL5_HCLK_FREQUENCY #define BOARD_LPTIM3_FREQUENCY STM32WL5_HCLK_FREQUENCY /**************************************************************************** * Pre-processor Definitions ****************************************************************************/ /* Alternate function pin selections ****************************************/ /* USART1: * RXD: PB7 (D0 on arduino pinout) * TXD: PB6 (D1 on arduino pinout) */ #define GPIO_USART1_RX GPIO_USART1_RX_2 /* PB7 */ #define GPIO_USART1_TX GPIO_USART1_TX_2 /* PB6 */ /* LPUART1 * Connected to virtual com port */ #define GPIO_LPUART1_RX GPIO_LPUART1_RX_1 /* PA3 */ #define GPIO_LPUART1_TX GPIO_LPUART1_TX_1 /* PA2 */ #define GPIO_SPI1_MISO GPIO_SPI1_MISO_2 #define GPIO_SPI1_MOSI GPIO_SPI1_MOSI_2 #define GPIO_SPI1_SCK GPIO_SPI1_SCK_2 #define GPIO_SPI2S2_MISO GPIO_SPI2_MISO_2 #define GPIO_SPI2S2_MOSI GPIO_SPI2_MOSI_2 #define GPIO_SPI2S2_SCK GPIO_SPI2_SCK_3 /* user buttons * * There are 3 buttons provided for user to program * * PA0 - Button 1 * PA1 - Button 2 * PC6 - Button 3 * * Buttons need to be pulled up internally by chip, * and button press will pull pin down to LOW level. */ #define BOARD_BUTTON1 0 #define BOARD_BUTTON2 1 #define BOARD_BUTTON3 2 #define BOARD_NBUTTONS 3 #define BUTTON1_BIT (1 << BOARD_BUTTON1) #define BUTTON2_BIT (1 << BOARD_BUTTON2) #define BUTTON3_BIT (1 << BOARD_BUTTON3) /* LEDs * * The Nucleo wl55jc board provides 3 user leds * PB15 - blue LED * PB11 - red LED * PB9 - green LED * * - When the I/O is HIGH value, the LED is on. * - When the I/O is LOW, the LED is off. */ /* LED index values for use with board_userled() */ #define BOARD_LED_BLUE 0 #define BOARD_LED_GREEN 1 #define BOARD_LED_RED 2 #define BOARD_NLEDS 3 /* LED bits for use with board_userled_all() */ #define BOARD_LED_BLUE_BIT (1 << BOARD_LED_BLUE) #define BOARD_LED_GREEN_BIT (1 << BOARD_LED_GREEN) #define BOARD_LED_RED_BIT (1 << BOARD_LED_RED) /* These LEDs are not used by the board port unless CONFIG_ARCH_LEDS is * defined. In that case, the usage by the board port is defined in * include/board.h and src/stm32_autoleds.c. The LEDs are used to encode * OS-related events as follows: * * SYMBOL Val Meaning LED state * BLUE GREEN RED * ----------------- --- ----------------------- ---- ----- ---- */ #define LED_STARTED 1 /* NuttX has been started ON OFF OFF */ #define LED_HEAPALLOCATE 2 /* Heap has been allocated OFF ON OFF */ #define LED_IRQSENABLED 3 /* Interrupts enabled ON ON OFF */ #define LED_STACKCREATED 4 /* Idle stack created OFF OFF ON */ #define LED_INIRQ 5 /* In an interrupt GLOW N/C N/C */ #define LED_SIGNAL 6 /* In a signal handler GLOW N/C N/C */ #define LED_ASSERTION 7 /* An assertion failed GLOW N/C N/C */ #define LED_PANIC 8 /* The system has crashed ON ON ON */ #undef LED_IDLE /* MCU is is sleep mode Not used */ /**************************************************************************** * Public Data ****************************************************************************/ #ifndef __ASSEMBLY__ #undef EXTERN #if defined(__cplusplus) #define EXTERN extern "C" extern "C" { #else #define EXTERN extern #endif /**************************************************************************** * Public Function Prototypes ****************************************************************************/ /**************************************************************************** * Name: stm32wl5_board_initialize * * Description: * All STM32WL5 architectures must provide the following entry point. * This entry point is called early in the initialization -- after all * memory has been configured and mapped but before any devices have been * initialized. * ****************************************************************************/ void stm32wl5_board_initialize(void); #undef EXTERN #if defined(__cplusplus) } #endif #endif /* __ASSEMBLY__ */ #endif /* __BOARDS_ARM_STM32WL5_NUCLEO_WL55JC_INCLUDE_BOARD_H */