Gregory Nutt is the copyright holder for those files and he has submitted the
SGA as a result we can migrate the licenses to Apache.
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
Alan Carvalho de Assis has submitted the SGA and we can migrate the licenses
to Apache.
Gregory Nutt has submitted the SGA and we can migrate the licenses
to Apache.
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
There is a good case on sim platform:
When we input some cmd and click enter key to start application in terminal,
this context will change to application from IDLE loop. Althrough entey key '\r'
has been received to recv buffer and complete post semaphore of reader, but
pollnotify may not be called because context change. So when application run
poll function, because no events happend and poll enter wait, context will
again change to IDLE loop, this pollnotify of IDLE loop will run to send poll
events, poll function of applicaton will wake up. It's wrong!
Change-Id: I812a889f2e90781a9c3cb4b0251cccc4d32bebd1
Signed-off-by: dongjiuzhu <dongjiuzhu1@xiaomi.com>
This adds support for the Q10 BlackBerry based keyboard
from Solder Party. https://www.solder.party/docs/keyboard-pmod/
They keyboard device registered at /dev/kbdN is fully compatible
with hidkbd and has been testing with the Keyboard FeatherWing
on the nRF52 platform.
The buttons are added as a standard discrete joystick if
optionally enabled. The PMOD variant of this does not
include these buttons, but the Keyboard FeatherWing does.
This joystick is usually defined at /dev/djoyN and
can be used with the djoy example application.
Signed-off-by: Brennan Ashton <bashton@brennanashton.com>
This patch resolves to bugs in the GPIO interrupt logic:
1. Any pins did not have STMPE811_GPIO_RISING in their pincfg
would clear the rising edge interrupt enable flag for all
pins due to a masking bug.
2. Pins would never trigger a second interrupt. There is an
undocumented requirement that you have to clear both the
GPIO interrupt status register __and__ also the edge
detection status register. Failure to clear either of
these will result in no further interrupts being triggered.
This requirement exists both for edge and level modes of
operation.
Signed-off-by: Brennan Ashton <bashton@brennanashton.com>
to save the preserved space(1KB) and also avoid the heap overhead
Signed-off-by: Xiang Xiao <xiaoxiang@xiaomi.com>
Change-Id: I694073f68e1bd63960cedeea1ddec441437be025
so the lower half driver don't need include the specific board.h
Signed-off-by: Xiang Xiao <xiaoxiang@xiaomi.com>
Change-Id: I2ff5c30049a5c5e8ee90baea56e9f4cb1a8a4f87
Resolution of Issue 619 will require multiple steps, this part of the first step in that resolution: Every call to nxsem_wait_uninterruptible() must handle the return value from nxsem_wait_uninterruptible properly. This commit is only for those files under drivers/input.
This reverts commit b9ace36fcc.
This change was added by PR 625 but has a serious logic flaw. It removes all occurrences of INCDIROPT and replaces it with a definition in tools/Config.mk:
else ifeq ($(WINTOOL),y)
DEFINE = "$(TOPDIR)/tools/define.sh"
INCDIR = "$(TOPDIR)/tools/incdir.sh" -w
This logic flaw is the Config.mk is included in all Make.defs files BEFORE WINTOOL is defined. As a result, the definition is wrong in many places when building under Cygwin with a Windows native toolchain.
This commit does two things:
1. First, it reorganizes the driver Kconfig files so that each is self contained. Before, a part of the driver configuration was in drivers/Kconfig and the rest was in in drivers/xyz/Konfig. Now, all of the driver configuration is consolitated in the latter.
2. Second, this commit correct numerous serious errors introduced in a previous reorganization of the driver Kconfig files. This was first noted by Nicholas Chin in PR270 for the case of the drivers/i2c/Kconfig but some examination indicates that the error was introduced into several other Kconfig files as well.
The nature of the introduced error was basically this:
- Nothing must intervene between the menuconfig selection and the following conditional configuration otpions.
- A previous PR erroneously introduced unconditional options between the menuconfig and the following confditional logic, thus corrupting the driver menus.
This error was easy to make because the driver Kconfig files were not well modularized. Making them fully self-contained should eliminate this kind of error in the future.
Author: Alan Carvalho de Assis <acassis@gmail.com>
Run all .h and .c files modified in last PR through nxstyle.
Author: Xiang Xiao <xiaoxiang@xiaomi.com>
Fix stm32l4_otgfshost.c: error: 'ret' undeclared (#32)
result by commit 6a3c2aded6
Change-Id: I68ba79417d8da102da8d91c74496961aef242dd9
Signed-off-by: Xiang Xiao <xiaoxiang@xiaomi.com>
* Simplify EINTR/ECANCEL error handling
1. Add semaphore uninterruptible wait function
2 .Replace semaphore wait loop with a single uninterruptible wait
3. Replace all sem_xxx to nxsem_xxx
* Unify the void cast usage
1. Remove void cast for function because many place ignore the returned value witout cast
2. Replace void cast for variable with UNUSED macro
arch/: Removed all references to CONFIG_DISABLE_POLL. The standard POSIX poll() can not longer be disabled.
sched/ audio/ crypto/: Removed all references to CONFIG_DISABLE_POLL. The standard POSIX poll() can not longer be disabled.
Documentation/: Removed all references to CONFIG_DISABLE_POLL. The standard POSIX poll() can not longer be disabled.
fs/: Removed all references to CONFIG_DISABLE_POLL. The standard POSIX poll() can not longer be disabled.
graphics/: Removed all references to CONFIG_DISABLE_POLL. The standard POSIX poll() can not longer be disabled.
net/: Removed all references to CONFIG_DISABLE_POLL. The standard POSIX poll() can not longer be disabled.
drivers/: Removed all references to CONFIG_DISABLE_POLL. The standard POSIX poll() can not longer be disabled.
include/, syscall/, wireless/: Removed all references to CONFIG_DISABLE_POLL. The standard POSIX poll() can not longer be disabled.
configs/: Remove all references to CONFIG_DISABLE_POLL. Standard POSIX poll can no longer be disabled.
libs/: Remove references to CONFIG_DISABLE_SIGNALS. Signals can no longer be disabled.
syscall/: Remove references to CONFIG_DISABLE_SIGNALS. Signals can no longer be disabled.
wireless/: Remove references to CONFIG_DISABLE_SIGNALS. Signals can no longer be disabled.
Documentation/: Remove references to CONFIG_DISABLE_SIGNALS. Signals can no longer be disabled.
include/: Remove references to CONFIG_DISABLE_SIGNALS. Signals can no longer be disabled.
drivers/: Remove references to CONFIG_DISABLE_SIGNALS. Signals can no longer be disabled.
sched/: Remove references to CONFIG_DISABLE_SIGNALS. Signals can no longer be disabled.
configs: Remove references to CONFIG_DISABLE_SIGNALS. Signals can no longer be disabled.
arch/xtensa: Remove references to CONFIG_DISABLE_SIGNALS. Signals can no longer be disabled.
arch/z80: Remove references to CONFIG_DISABLE_SIGNALS. Signals can no longer be disabled.
arch/x86: Remove references to CONFIG_DISABLE_SIGNALS. Signals can no longer be disabled.
arch/renesas and arch/risc-v: Remove references to CONFIG_DISABLE_SIGNALS. Signals can no longer be disabled.
arch/or1k: Remove all references to CONFIG_DISABLE_SIGNALS. Signals are always enabled.
arch/misoc: Remove all references to CONFIG_DISABLE_SIGNALS. Signals are always enabled.
arch/mips: Remove all references to CONFIG_DISABLE_SIGNALS. Signals are always enabled.
arch/avr: Remove all references to CONFIG_DISABLE_SIGNALS. Signals are always enabled.
arch/arm: Remove all references to CONFIG_DISABLE_SIGNALS. Signals are always enabled.
drivers/timers/rtc.c: Support signal notification through SIGEV_THREAD
drivers/input/ajoystick.c: Support signal notification through SIGEV_THREAD
drivers/input/djoystick.c: Support signal notification through SIGEV_THREAD
drivers/input/button_upper.c: Support signal notification through SIGEV_THREAD
drivers/sensors/zerocross.c: Support signal notification through SIGEV_THREAD
drivers/wireless/ieee802154: Support signal notification through SIGEV_THREAD
drivers/lcd/ft80x.c: Support signal notification through SIGEV_THREAD
No... I was misled. The shutdown function is usually called when the
driver is unlinked. But not in this case. In this case, it is simply
called when the last reference is closed. And no, you don't want to
detach the interrupt handler in that case. My bad.
This reverts commit b79e6b9c9a.
stm32f746g-disco: touchscreen support
* fixed FT5x06 driver to correctly close (previously it unregistered interrupt handler during close)
* added LittlevGL demo for STM32F746G-DISCO
Approved-by: GregoryN <gnutt@nuttx.org>
Fix GPIO operation of STMPE811 driver.
Fixed issues:
1. STMPE811_GPIO_DIR was defined for register name
and later was redefined to be the pin direction mask
for `stmpe811_gpioconfig`
I decided to change register name to be STMPE811_GPIO_DIR_REG,
and keep pin direction mask STMPE811_GPIO_DIR, so that any
external code that already use this driver will be unchanged.
2. The STMPE811 register GPIO_DIR uses bit value 1 for output
and 0 for input, but `stmpe811_gpioconfig` set the opposite.
3. The call to `stmpe811_gpiowrite` from inside of `stmpe811_gpioconfig`
leaded to deadlock.
Approved-by: Gregory Nutt <gnutt@nuttx.org>
Replace all calls to sigqueue() in the OS proper with calls to nxsig_queue() to avoid accessing the errno variable.
sched/signal: Add nxsig_queue() which is functionally equivalent to sigqueue() except that it does not modify the errno variable.
Squashed commit of the following:
Change all calls to usleep() in the OS proper to calls to nxsig_usleep()
sched/signal: Add a new OS internal function nxsig_usleep() that is functionally equivalent to usleep() but does not cause a cancellaption point and does not modify the errno variable.
sched/signal: Add a new OS internal function nxsig_sleep() that is functionally equivalent to sleep() but does not cause a cancellaption point.
This commit backs out most of commit b4747286b1. That change was added because sem_wait() would sometimes cause cancellation points inappropriated. But with these recent changes, nxsem_wait() is used instead and it is not a cancellation point.
In the OS, all calls to sem_wait() changed to nxsem_wait(). nxsem_wait() does not return errors via errno so each place where nxsem_wait() is now called must not examine the errno variable.
In all OS functions (not libraries), change sem_wait() to nxsem_wait(). This will prevent the OS from creating bogus cancellation points and from modifying the per-task errno variable.
sched/semaphore: Add the function nxsem_wait(). This is a new internal OS interface. It is functionally equivalent to sem_wait() except that (1) it is not a cancellation point, and (2) it does not set the per-thread errno value on return.
sched/semaphore: Add nxsem_post() which is identical to sem_post() except that it never modifies the errno variable. Changed all references to sem_post in the OS to nxsem_post().
sched/semaphore: Add nxsem_destroy() which is identical to sem_destroy() except that it never modifies the errno variable. Changed all references to sem_destroy() in the OS to nxsem_destroy().
libc/semaphore and sched/semaphore: Add nxsem_getprotocol() and nxsem_setprotocola which are identical to sem_getprotocol() and set_setprotocol() except that they never modifies the errno variable. Changed all references to sem_setprotocol in the OS to nxsem_setprotocol(). sem_getprotocol() was not used in the OS
libc/semaphore: Add nxsem_getvalue() which is identical to sem_getvalue() except that it never modifies the errno variable. Changed all references to sem_getvalue in the OS to nxsem_getvalue().
sched/semaphore: Rename all internal private functions from sem_xyz to nxsem_xyz. The sem_ prefix is (will be) reserved only for the application semaphore interfaces.
libc/semaphore: Add nxsem_init() which is identical to sem_init() except that it never modifies the errno variable. Changed all references to sem_init in the OS to nxsem_init().
sched/semaphore: Rename sem_tickwait() to nxsem_tickwait() so that it is clear this is an internal OS function.
sched/semaphoate: Rename sem_reset() to nxsem_reset() so that it is clear this is an internal OS function.
Entropy pool gathers environmental noise from device drivers, user-space, etc., and returns good random numbers, suitable for cryptographic use. Based on entropy pool design from *BSDs and uses BLAKE2Xs algorithm for CSPRNG output.
Patch also adds /dev/urandom support for using entropy pool RNG and new 'getrandom' system call for getting randomness without file-descriptor usage (thus avoiding file-descriptor exhaustion attacks). The 'getrandom' interface is similar as 'getentropy' and 'getrandom' available on OpenBSD and Linux respectively.
put_reg/get_reg function was overriding i2c transfer error code with i2creset return value, that lead to OK status although actual transfer failed.
Signed-off-by: Juha Niskanen <juha.niskanen@haltian.com>
Reported-by: Harri Luhtala <harri.luhtala@haltian.com>
Provide a user defined callback context for irq's, such that when
registering a callback users can provide a pointer that will get
passed back when the isr is called.
Alin Jerpelea