Although the LED might be RGB-only, the LED data is packed in a
32-bit long variable and, then, this is the default size of a LED
pixel to define the 'WS2812_RW_PIXEL_SIZE' macro. Please note that
the lower-half driver will deal with the case of the addressable
LED being 3 or 4-pixel sized.
The RMT (Remote Control) character driver allows to use the RMT
peripheral (usually, a one-wire peripheral dedicated to driving
IR remote control) as a character driver.
Please note that this perpiheral depends on the lower-half specific
driver implementation.
Add a static port-based VLAN configuration for KSZ9477 switch. This doesn't
use the VLAN tagging, but is a switch's internal mechanism to simply configure
if the packet forwarding is allowed from one port to another.
Signed-off-by: Jukka Laitinen <jukkax@ssrc.tii.ae>
The Goldfish FB register should be optimized by considering the need to pass in parameters for base and irq.
Signed-off-by: jianglianfang <jianglianfang@xiaomi.com>
The opening and closing of the window has been associated with the opening and closing of fb, but the LCD has not yet been optimized. The window will only open when sim_x11openwindow is called, and similarly, the window will only close when sim_x11closewindow is called.
Signed-off-by: jianglianfang <jianglianfang@xiaomi.com>
-The qemu wifi fucntion only supports the STA mode and the following
operations:
wapi mode wlan0 2
wapi scan wlan0
wapi psk wlan0 password 3
wapi essid wlan0 wifi_name 1
wapi show wlan0
wapi disconnect wlan0
-Eanble the virtual wifi function with the MACRO `CONFIG_DRIVERS_WIFI_SIM`.
Signed-off-by: liqinhui <liqinhui@xiaomi.com>
Previously ipv6 multi-address support decided packet source
address based on its destination. This doesn't work if NuttX
device has multiple addresses within same subnet.
Instead when a packet is a response to existing connection,
the source address should be based on the destination address
used in the received packet.
There is a problem with the current elf loader for risc-v: when a pair of
PCREL_HI20 / LO12 relocations are encountered, it is assumed that these
will follow each other immediately, as follows:
label:
auipc a0, %pcrel_hi(symbol) // R_RISCV_PCREL_HI20
load/store a0, %pcrel_lo(label)(a0) // R_RISCV_PCREL_LO12_I/S
With this assumption, the hi/lo relocations are both done when a hi20
relocation entry is encountered, first to the current instruction (addr)
and to the next instruction (addr + 4).
However, this assumption is wrong. There is nothing in the elf relocation
specification[1] that mandates this. Thus, the hi/lo relocation always
needs to first fixup the hi-part, and when the lo-part is encountered, it
needs to find the corresponding hi relocation entry, via the given "label".
This necessitates (re-)visiting the relocation entries for the current
section as well as looking for "label" in the symbol table.
The NuttX elf loader does not allow such operations to be done in the
machine specific part, so this patch fixes the relocation issue by
introducing an architecture specific cache for the hi20 relocation and
symbol table entries. When a lo12 relocation is encountered, the cache
can be consulted to find the hi20 part.
[1] https://github.com/riscv-non-isa/riscv-elf-psabi-doc/blob/master/riscv-elf.adoc
we can use uart to debug nuttx,like debugger:
1. read/write memory
2. Use watchpoint,breakpoint,single step.
use up_debugpoint api
3. Ctrl+c to stop, continue, or single step.
hold uart send and receive
4. register a panic event, when crash or assert/panic, we use uart to
debug.
Signed-off-by: anjiahao <anjiahao@xiaomi.com>
Usage:
1. CONFIG_FS_PROCFS_MAX_STACK_RECORD > 0, such as 32,
2. add '-finstrument-functions' to CFLAGS for What you want to check
stack.
3. mount porcfs
4. cat /proc/<pid>/stack will print backtace & size
Signed-off-by: anjiahao <anjiahao@xiaomi.com>
Add registration function instrumentation API,
which can achieve instrumentation of entering and
exiting functions through the compiler's functionality.
We can use CONFIG_ARCH_INSTRUMENT_ALL to add instrumentation for all
source, or add '-finstrument-functions' to CFLAGS for Part of the
source.
Notice:
1. use CONFIG_ARCH_INSTRUMENT_ALL must mark _start or entry noinstrument_function,
becuase bss not set.
2. Make sure your callbacks are not instrumented recursively.
use instrument_register to register entry function and exit function.
They will be called by the instrumented function
Signed-off-by: anjiahao <anjiahao@xiaomi.com>
Virtio driver can used this api to judge whether the this feature
is supported by both virtio driver and device.
Signed-off-by: Bowen Wang <wangbowen6@xiaomi.com>
Previously CONFIG_USBDEV_SOFINTERRUPT existed in many platform
drivers but did nothing. This commit adds a callback function
usbdev_sof_irq() that can be used to take action on this interrupt.
A new locking mechanism: read/write locks
When there is a writer it is not possible to put on a read lock or a write lock; when there is a reader it is possible to reenter the read lock but not the write lock.
Writers are exclusive locks, readers are shared locks.
At the same time through the waiter count to determine whether there is currently a blocked task, if there is then in the unlock time to wake up all the waiter, through the priority of the competition to complete the blocked lock execution.
For example:
When we have a reader blocking two waiter writers, when the reader is unlocked it wakes up both writers. The writer with higher priority wakes up and checks for a successful condition and locks the lock, the second writer wakes up and fails to check for a condition and continues to block the lock.
Signed-off-by: chenrun1 <chenrun1@xiaomi.com>
1. Configurable mapping of virtual address to psram physical address
2. Access SPIRAM memory at high physical address through bank switching
Signed-off-by: chenwen@espressif.com <chenwen@espressif.com>
Adds support for POSIX interface open_memstream() that allows writing
to dynamic memory buffer stream. The stream is dynamically reallocated
as the buffer grows with initial size set to zero.
The caller has to free the buffer after the stream is closed.
The implementation uses fopencookie() for custom stream operations and
callbacks.
Signed-off-by: Michal Lenc <michallenc@seznam.cz>
To avoid losing the first frame, the set_buf needs to excute first. At the same time, imgdata->start_capture should excuted before the imgsensor->start_capture.
Signed-off-by: yaojingwei <yaojingwei@xiaomi.com>
This moves all the public POSIX semaphore functions into libc and with
this most of the user-space logic is also moved; namely cancel point and
errno handling.
This also removes the need for the _SEM_XX macros used to differentiate
which API is used per user-/kernel mode. Such macros are henceforth
unnecessary.
After this, RISC-V fully supports the kmap interface.
Due to the current design limitations of having only a single L2 table
per process, the kernel kmap area cannot be mapped via any user page
directory, as they do not contain the page tables to address that range.
So a "kernel address environment" is added, which can do the mapping. The
mapping is reflected to every process as only the root page directory (L1)
is copied to users, which means every change to L2 / L3 tables will be
seen by every user.
The driver's main purpose is to support the porting of the open source
component optee_client (https://github.com/OP-TEE/optee_client) to nttux.
The basic function of the driver module is to convert the REE application layer data and send it to the TEE through rpmsg.
The main functions include
1 driver registration.
we need to register a device driver(/dev/tee0) through optee_register function.
2 open the driver
3 ioctl the driver
The ioctl command passes different parameters and commands, and interacts with the TEE through rpmsg.
4 close the driver
Signed-off-by: hujun5 <hujun5@xiaomi.com>
A segmentfault might happen when read/write/unlink ops called without an open
ops called because it bind ept's ops in rpmsgblk_open_handler.
proxy> rm /dev/ram1
segmentfault
proxy> ls /dev/ram1
segmentfault
Signed-off-by: liaoao <liaoao@xiaomi.com>
PR #11165 causes an unnecessary regression; task_delete no longer works,
if the deleted task is from another group.
The logic that prevents this comes from:
nxnotify_cancellation() ->
tls_get_info_pid() ->
nxsched_get_stackinfo()
Which checks for permissions, which does not make sense in this case since
it is the kernel asking for the stack information.
Fix this by partially reverting 11165 and implementing a direct path for
the kernel to query for any tasks TLS.
Commit 9244b5a737 added support
for non-standard field si_user that is useful for passing context
pointers to signal handlers.
This commits makes it work for all signals, not just SA_KERNELHAND.
Previously si_user for normal signals was uninitialized garbage.
TimJTi