Gregory Nutt
|
cbcabe3314
|
Removed almost all ostest configurations
|
2014-02-28 19:19:11 -06:00 |
|
Gregory Nutt
|
47ca6ef4d4
|
configs/*/defconfig: If CONFIG_NSH_LIBRARY is set, make sure that CONFIG_NSH_READLINE is also set or the configuration will use the CLE the next time it is reconfigured
|
2014-02-28 07:45:51 -06:00 |
|
Gregory Nutt
|
3b07bc6716
|
SAM4E: Update SAM3/4 TC and DMAC register definition header files
|
2014-02-25 10:56:23 -06:00 |
|
Gregory Nutt
|
2f837ccd2a
|
rename up_led*() functions to board_led_*()
|
2014-01-24 14:28:49 -06:00 |
|
Gregory Nutt
|
f3f5378acc
|
The optimization level can now be selected as part of the configuration
|
2014-01-24 07:45:35 -06:00 |
|
Gregory Nutt
|
cbf86ac01f
|
Finishes separation of debug symbols and optimization selections
|
2013-12-20 13:23:42 -06:00 |
|
Gregory Nutt
|
98410588e8
|
Arduino Due: RXD0 pull-up works with both REV2 and REV3
|
2013-10-10 07:11:13 -06:00 |
|
Gregory Nutt
|
3b6e63199a
|
Add option to enable Aduino Due specific logic, like pull-up on UART0 RXD. Suggested by gdi@embedders.org
|
2013-10-09 07:35:00 -06:00 |
|
Gregory Nutt
|
b3ecd158ac
|
Mov apps/examples/composite to apps/system/composite; convert configs/stm3210e-eval/composite to use kconfig-frontend tools -- untested
|
2013-09-25 18:50:14 -06:00 |
|
Gregory Nutt
|
0b450bc202
|
Move apps/examples/usbmsc to apps/system/usbmsc
|
2013-09-25 16:54:39 -06:00 |
|
Gregory Nutt
|
70f0ffdfc5
|
Finally... renamed all CONFIG_DRAM_ settings to CONFIG_RAM_
|
2013-07-26 10:09:17 -06:00 |
|
Gregory Nutt
|
04b3bb1826
|
Revamp the way external memory regions are configured; Add logic to add SAMA5 external memory regions to the heap
|
2013-07-24 10:08:32 -06:00 |
|
Gregory Nutt
|
37ed44a1ee
|
Fix type in the USB composite device driver
|
2013-07-04 07:47:32 -06:00 |
|
Gregory Nutt
|
bb69466c8b
|
Updates for the Sure PIC32 board
|
2013-07-03 11:39:54 -06:00 |
|
Gregory Nutt
|
ac36a07e24
|
Back out part of last change to the Arduino Due touchscreen driver
|
2013-07-03 09:07:01 -06:00 |
|
Gregory Nutt
|
94e2f4ceb4
|
Fix SAM34 interrupt handling for ports D-F; fix MISO logic in Arduino Due touchscreen driver
|
2013-07-03 08:12:45 -06:00 |
|
Gregory Nutt
|
f0ebaf8312
|
Several fixes to get a clean compile of the Arduino touch screen
|
2013-07-02 13:52:09 -06:00 |
|
Gregory Nutt
|
0ff5a0c791
|
Correct port direction for Arduino MISO signal
|
2013-07-02 12:37:20 -06:00 |
|
Gregory Nutt
|
d9279febb9
|
Flesh out a few missing pieces for the Arduino ITEAD TFT shield
|
2013-07-02 11:36:48 -06:00 |
|
Gregory Nutt
|
cfb156f286
|
Add support for touchscreen on ITEAD Arduino shield. Untested
|
2013-07-02 08:25:53 -06:00 |
|
Gregory Nutt
|
bdf96a93db
|
Revise how delays are calculated in SPI bit bang driver so that we may get a little better frequency resolution
|
2013-07-01 20:55:36 -06:00 |
|
Gregory Nutt
|
652c33a53a
|
clean up of SPI bit bang logic
|
2013-07-01 17:49:43 -06:00 |
|
Gregory Nutt
|
e1dab23711
|
Add a general bit-bang SPI lower-half driver and implement the bit-bang driver for the Arduino ITEAD TFT shield
|
2013-07-01 16:50:16 -06:00 |
|
Gregory Nutt
|
8b68ea2f94
|
Add a general bit-bang SPI upper-half driver
|
2013-07-01 12:23:26 -06:00 |
|
Gregory Nutt
|
09faaccc02
|
Created new directories to hold SPI-related files
|
2013-07-01 08:11:54 -06:00 |
|
Gregory Nutt
|
940b82bf61
|
quick and not very accurate calibration of arduino due timing loops
|
2013-06-28 15:50:44 -06:00 |
|
Gregory Nutt
|
3505ca7556
|
Add an NSH configuration for the Arduino Due; Pluse several fixes related to the Due and to the SAM3X in general
|
2013-06-28 14:32:08 -06:00 |
|
Gregory Nutt
|
e34e1ee987
|
Arduino Due: Fixes to FLASH address, flash wait states, updated Comments. Now boots and runs a bit before crashing
|
2013-06-28 11:29:14 -06:00 |
|
Gregory Nutt
|
f20f23cf31
|
Add instructions to use BOSSA to load nuttx into Due
|
2013-06-28 08:54:09 -06:00 |
|
Gregory Nutt
|
9956392d00
|
With these changes the Arduino Due port builds without errors
|
2013-06-27 15:07:07 -06:00 |
|
Gregory Nutt
|
e0310e2cc8
|
Flesh out the Arduino Due board configuratino and integrate it with the build and configuration system
|
2013-06-27 14:24:27 -06:00 |
|
Gregory Nutt
|
bc7ac20616
|
Add peripheral configuration logic for the SAM3X/3A; Change all references to SAM3/4 SPI to SPI0 for compatibity with the SAM3X/3A which has SPI0 and SPI1; Add directory which will eventually holdl an Arduino Due port
|
2013-06-26 18:46:44 -06:00 |