- Add mmap into file_operations and remove it from ioctl definitions.
- Add mm_map structure definitions to support future unmapping
- Modify all drivers to initialize the operations struct accordingly
Signed-off-by: Jukka Laitinen <jukkax@ssrc.tii.ae>
1.Don't check the return value of nxsem_init or nxmutex_init
2.Fix some style issue
Signed-off-by: anjiahao <anjiahao@xiaomi.com>
Signed-off-by: Xiang Xiao <xiaoxiang@xiaomi.com>
0c3db448bb
added the option to generate the waveforms to drive ws2812 and similar LEDs using different
hardware (e.g. RP2040 PIO instead of SPI).
For that new mode, the concept of CONFIG_WS2812_FREQUENCY is different. Instead of
the SPI frequency (commonly a few MHz), it is the frequency of the actual output waveform
(commonly 400 or 800 kHz).
There was an attempt to express the SPI frequency divided by 10, but it's not actually the
case either (it would be divided by 8).
I think it is clearer to explain in Kconfig what CONFIG_WS2812_FREQUENCY means for each mode
and go back to the previous behaviour for the original SPI mode (also to avoid breaking
out-of-tree boards).
Gregory Nutt is the copyright holder for those files and he has submitted the
SGA as a result we can migrate the licenses to Apache.
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
State of problem:
- Some drivers that do not support write operations (does not
have write handler or ioctl do not perform any write actions)
are registered with write permissions
- Some drivers that do not support read operation (does not
have read handler or ioctl do not perform any read actions)
are registered with read permissions
- Some drivers are registered with execute permissions
Solution:
- Iterate code where register_driver() is used and change 'mode'
parameter to reflect the actual read/write operations executed
by a driver
- Remove execute permissions from 'mode' parameter
Signed-off-by: Petro Karashchenko <petro.karashchenko@gmail.com>
DS Automotion GmbH has submitted the SGA and we can migrate the licenses
to Apache.
Gregory Nutt has submitted the SGA and we can migrate the licenses
to Apache.
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
Alan Carvalho de Assis has submitted the SGA and we can migrate the licenses
to Apache.
Gregory Nutt has submitted the SGA and we can migrate the licenses
to Apache.
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
It's not necessary to send a reset pulse after sending the RGB data
since the first thing that a new transmission does is sending the long
reset pulse. I have left 1 reset byte after the RGB data to keep some
padding given that the bits inside the byte are shifted by 1 bit although
I think it wouldn't be necessary either. But just in case.
This reduces the memory usage (you can easily save 60 bytes) and increases
the maximum refresh rate.
Previously only 4 MHz and 8 MHz were allowed. Given the tolerance
allowed in the WS2812 timing spec, frequency ranges around those
two can be used too which is useful for boards in which it is
difficult to generate those specific frequencies.
The WS2812 is very common in LED strips as it is an integrated
controller and LED. It is driven by a single data line, but
the timing requirements can be met by using most SPI controllers
and the use of DMA.
This driver has been validated on the nRF52 arch both with a
single LED and a strip of 144.
Signed-off-by: Brennan Ashton <bashton@brennanashton.com>
so the lower half driver don't need include the specific board.h
Signed-off-by: Xiang Xiao <xiaoxiang@xiaomi.com>
Change-Id: Icf6638a6865bac42150b5957376e55909f041d40
and let USERLED_LOWER depends on ARCH_HAVE_LEDS instead
Signed-off-by: Xiang Xiao <xiaoxiang@xiaomi.com>
Change-Id: Ie03e76d90b61a3d8d3457ccdd319a247b6075fa8
* Simplify EINTR/ECANCEL error handling
1. Add semaphore uninterruptible wait function
2 .Replace semaphore wait loop with a single uninterruptible wait
3. Replace all sem_xxx to nxsem_xxx
* Unify the void cast usage
1. Remove void cast for function because many place ignore the returned value witout cast
2. Replace void cast for variable with UNUSED macro
Xiang Xiao