Summary:
- This commit fixes the CI build errors regressed by
https://github.com/apache/incubator-nuttx/pull/7351
Impact:
- None
Testing:
- Build only
Signed-off-by: Masayuki Ishikawa <Masayuki.Ishikawa@jp.sony.com>
Currently the IHC (Inter Hart Communication) depends on OpenAMP and
rptun. However, the bootloader portion of the IHC doesn't need
either of them. Now they are wasting a lot of bootloader space.
Reorganize the bootloader portion into a separate file 'mpfs_ihc_sbi.c'.
This file contains the OpenSBI vendor extensions, or the only required
functionalities for the bootloader. On the other hand, 'mpfs_ihc.c'
contains the non-bootloader code.
This patch also makes it possible to utilize 2 RPMSG channels. This
has been tested so that 2 separate NuttXs on harts 1 and 2 communicate
with Linux kernel that runs on harts 3 and 4.
New configuration files are added as well:
- rpmsg-ch1: sample config for RPMSG
- rpmsg-ch2: sample config for another RPMSG channel
- rpmsg-sbi: sample bootloader config for RPMSG/OpenSBI
Signed-off-by: Eero Nurkkala <eero.nurkkala@offcode.fi>
Summary:
- I noticed that the OpenSBI library depends on the BSD license
- This commit fixes this issue
Impact:
- None
Testing:
- Build only
Signed-off-by: Masayuki Ishikawa <Masayuki.Ishikawa@jp.sony.com>
Simplify the clock mode from the board.h -files. Also make the
SD clock definable as well.
Co-authored-by: Petro Karashchenko <petro.karashchenko@gmail.com>
Signed-off-by: Eero Nurkkala <eero.nurkkala@offcode.fi>
Some related products, such as Aries m100pfs, don't support eMMC
speeds up to 200MHz. Thus, provide option to select slower clock.
This has only to do with the clocking, no CMD6 is sent to select
high speed modes.
Signed-off-by: Eero Nurkkala <eero.nurkkala@offcode.fi>
It is not really needed; g_hart_stacks is only used during SBI init as
a temporary stack area. We can use the scratch area buffers for this, as
the scratch areas define almost 4K of extra space, which is used for
exception stacks anyway.
Update PLL configuration parameters to match the values provided
by the vendor.
Also remove extra call to mpfs_pll_config() as it's already called
at mpfs_clockconfig().
Signed-off-by: Eero Nurkkala <eero.nurkkala@offcode.fi>
This provides USB composite (CDC/ACM and Mass Storage) support
for mpfs board. In addition, a number of USB fixes are included:
- Support for Setup Out packets
- Proper support for larger than packet size writes
- Finishing setup packets properly
Signed-off-by: Eero Nurkkala <eero.nurkkala@offcode.fi>
This provides an example of Asymmetric Multiprocessing (AMP). The
master from Linux sends pings that this NuttX echoes back. The system
uses RPMsg from OpenAMP.
The Inter-Hart Communication module is present in the vendor's software
stack with the tag "2021.11". The software is present on github at the
polarfire-soc project. The following conditions must be met:
1. FPGA programmed with 2021.11 software
2. HSS (Vendor bootloader) with 2021.11 software
3. U-boot and Linux kernel from 2011.11 software
Currently the IHC works as a slave only on the hart number 4.
On the NuttX side, this patch uses rptun that incorporates rpmsg and
virtio. If it used only rpmsg and virtio, the future maintenance would
likely be much heavier. Using rptun also simplifies many things.
Upon success, the master side from Linux may issue an example test:
root@icicle-kit-es-amp:/opt/microchip/amp/rpmsg-pingpong# ./rpmsg-pingpong
However, the rpmsg-pingpong.c (compiled on target with gcc), may need to
be modified as seen below to match the device id:
- char *rpmsg_dev="virtio0.rpmsg-amp-demo-channel.-1.0";
+ char *rpmsg_dev="virtio0.rpmsg-amp-demo-channel.-1.1024";
This work uses a separate linker script. Due to a bug yet unknown to date,
a small NuttX, when loaded by the vendor HSS bootloader, will cause the
Linux kernel to hang at boot. Thus, the binary size is increased with
a section 'filler_area' whose only purpose is to increase the image size
so that the Linux kernel will boot up.
Signed-off-by: Eero Nurkkala <eero.nurkkala@offcode.fi>
Mappings are done with vaddr=paddr.
- I/O space mapped with two gigapages
- Kernel space mapped to statically allocated page tables. 2MB of kernel
memory is supported.
- Page pool is mapped to the kernel space, to allow virtual memory access
for the kernel e.g. to initialize the page memory when it is allocated.
Enable this option to optimization the unused input sections with the
linker by compiling with " -ffunction-sections -fdata-sections ", and
linking with " --gc-sections ".
Signed-off-by: chao.an <anchao@xiaomi.com>
Move the target specific memory map to a separate file so there is no
need to copy&paste the __xxram_start etc linker symbols to each file
that needs them.
Also add MMU flags for I/O and kernel areas, they will be needed
when the kernel runs with virtual addresses also.
Mux USB IO pins one-by-one using package specific pinmux definitions. This avoids accidentally overwriting IO settings for other pins.
Signed-off-by: Jukka Laitinen <jukkax@ssrc.tii.ae>
This adds a simple USB device driver for the mpfs. However,
this driver is still at its early phase. Only limited testing
with CDC/ACM has been conducted.
Signed-off-by: Eero Nurkkala <eero.nurkkala@offcode.fi>
## Summary
A lot of linker scripts were listed twice, once for unix, once for windows.
This PR cleans up the logic so they're only listed once.
## Impact
Any opportunity to use a single source of truth and reduce lines of code is a win!
## Testing
CI will test all build
Summary:
- Apply the same style as sabre-6quad
Impact:
- None
- NOTE: esp32c3-devkit still remains old style because of link errors
Testing:
- Build only
Signed-off-by: Masayuki Ishikawa <Masayuki.Ishikawa@jp.sony.com>
Ville Juven