Channel polarity can now be set with PWMIOC_SETCHARACTERISTICS ioctl
command as field cpol was added to pwm_info_s structure. This way the
polarity can be easily set from application layer for each channel
apart and also can be change on at runtime if required (although this is
not likely).
Helper defines were also added to simplify the definition of low and high
polarity level. Architecture level should take care of writing the
polarity to correct MCU registers.
Signed-off-by: Michal Lenc <michallenc@seznam.cz>
Documentation for PWMIOC_SETCHARACTERISTICS ioctl command mentioned
that this command will neither start nor stop the pulsed output. This
however is incorrect as PWMIOC_SETCHARACTERISTICS command leads to
pwm_start() function which starts the pulsed output.
While this might not be the correct behaviour (I would probably welcome
the option to set PWM characteristics without starting the pulsed output)
it is the way the PWM driver is coded for many architectures. Future
enhancement might be to add function pwm_setchar() for example to just
set characteristics without starting the PWM output.
Signed-off-by: Michal Lenc <michallenc@seznam.cz>
PWM drivers use channel numbers 0 and -1 to skip the channel and/or
all following channels. This situation is well established in the drivers
however it was not mentioned in pwm.h file. This commit adds a comment
mentioning it.
Signed-off-by: Michal Lenc <michallenc@seznam.cz>
PWM drivers usually supports dead time generators that automatically
insert output activation delay for complementary PWM outputs. This
is usefull for some control purposes as control of H bridge for example.
This commit adds an application to driver interface that can be used
to set up those delays (if supported by the selected architecture)
directly from the application. The set up remains the same as for duty
cycle value.
The whole addition is by default disabled. It can be enabled by config
option PWM_DEADTIME.
Signed-off-by: Michal Lenc <michallenc@seznam.cz>
Generic drivers shoud not use architecture related config options like
CONFIG_SAMV7_PWM. This commit adds PWM pin overwrite under generic
configuration option CONFIG_PWM_OVERWRITE.
Now the overwrite can be used on other architectures as well or can be
completely disabled for SAMv7.
Signed-off-by: Michal Lenc <michallenc@seznam.cz>
Here is a case how to use arg:
If application need do the ADC conversion as the same frequency and phase
of PWM, he can pass a semaphore as arg and then PWM driver will post the
semaphore in he start point of every period.
Signed-off-by: zhangchengqi <zhangchengqi@xiaomi.com>
The current SAMv7 PWM driver assumes that all PWM channels should
work in sync mode, but that is a partial case of a generic PWM
driver operation.
Start SAMv7 PWM channels in async mode. The sync mode should be
implemeted either using ioctl command or via a separate Kconfig
option.
Signed-off-by: Petro Karashchenko <petro.karashchenko@gmail.com>
PWM drivers currently use channel number 0 for the channels that are not
used by the application. This commit adds number -1 which indicates that
all following channels are not configured and that the loop can be broken.
Signed-off-by: Michal Lenc <michallenc@seznam.cz>
Gregory Nutt is the copyright holder for those files and he has submitted the
SGA as a result we can migrate the licenses to Apache.
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
specified the name of remote proc(rpmsg server)
Change-Id: I0086bb43727a2bbb5e68f88907b5e4608182ef9c
Signed-off-by: Jiuzhu Dong <dongjiuzhu1@xiaomi.com>
Uros Platise has submitted the ICLA and we can migrate the licenses
to Apache.
David Sidrane has submitted the ICLA and we can migrate the licenses
to Apache.
Bob Feretich has submitted the ICLA and we can migrate the licenses
to Apache.
Gregory Nutt has submitted the SGA and we can migrate the licenses
to Apache.
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
Abdelatif Guettouche has submitted the ICLA and we can migrate the licenses
to Apache.
Gregory Nutt has submitted the SGA and we can migrate the licenses
to Apache.
Signed-off-by: Alin Jerpelea <alin.jerpelea@sony.com>
base/time/time_exploded_posix.cc:190:14: error: ‘struct tm’ has no member named ‘tm_zone’; did you mean ‘tm_mon’?
190 | timestruct.tm_zone = nullptr; // not a POSIX field, so mktime/timegm ignore
| ^~~~~~~
| tm_mon
Change-Id: I9f93e63b50c0692a7a2bfc47abd9d07aa2c8e8db
Signed-off-by: chao.an <anchao@xiaomi.com>
Gregory Nutt <gnutt@nuttx.org>
Run all .c and .h files modified in this PR through nxstyle and correct all coding standard problems.
Xiang Xiao <xiaoxiang@xiaomi.com>
Remove TIME_EXTENDED option to more conform C standard
Note: the code/data size increment is small
This port was effort of a number of people, I rather arbitrarily gave authorship to Guiding Li because he has the largest number of fundamental quashed commits from the Xiamoi repository.
Squashed commit of the following:
Author: Xiang Xiao <xiaoxiang@pinecone.net>
include/nuttx/b2c.h and libx/libc/string: Add non-standard string functions to deal with cases where there are more than 8-bits in a type char.
Author: Gregory Nutt <gnutt@nuttx.org>
Fix several build issues/missing definitiona needed for OpenAMP build in drivers/.
Add OpenAMP code has been reviewed and ran through tools/nxstyle (with all reports accounted for).
Author: Xiang Xiao <xiaoxiang@xiaomi.com>
tools/: Fix the minor issue in Makefile
Author: Gregory Nutt <gnutt@nuttx.org>
drivers/rptun/rptun.c: Review for coding standard. Run against tools/nxstyle.
tools/LibTargets.mk: Fix some TABs that were turned into spaces by a copy-paste.
fs/hostfs: Add configure and build support for hostfs RPC.
drivers/timer: Add configure and build support for syslog RTC.
drivers/syslog: Add configure and build support for syslog RPC.
drivers/serial: Add configure and build support for serial RPC.
Kconfig, tools/*.mk. openamp/: Add basic OpenAMP build support.
drivers/rptun: Add configure and build support for OpenAMP tunnel drivers.
drivers/net: Update Make.defs and Kconfig for OpenSDA support.
Remove drivers/clk/clk-rpmsg.c drivers/power/rpmsg_regulator.c. These depend on upstreaming support for a new subsystem based on the clk/regulator is model from Linux. Removed because we want to separate the activities. We will just try to get the basic OpenAMP support in place for now.
Remove drivers/misc/misc_rpmsg.c and include/nuttx/misc/misc_rpmsg.h. These are specific to the Xiaomi application.
Author: zhuyanlin <zhuyanlin@pinecone.net>
This commit brings in the OpenAMP OS driver/RPC components from https://github.com/FishsemiCode/nuttx. Initial commit is source files only. Additional changes to Kconfig and Make.defs files still needed.
Author: Jianli Dong <dongjianli@pinecone.net>
This commit brings in the OpenAMP OS driver/RPC components from https://github.com/FishsemiCode/nuttx. Initial commit is source files only. Additional changes to Kconfig and Make.defs files still needed.
Author: Guiding Li <liguiding@pinecone.net>
This commit brings in the OpenAMP OS driver/RPC components from https://github.com/FishsemiCode/nuttx. Initial commit is source files only. Additional changes to Kconfig and Make.defs files still needed.
libs/: Remove references to CONFIG_DISABLE_SIGNALS. Signals can no longer be disabled.
syscall/: Remove references to CONFIG_DISABLE_SIGNALS. Signals can no longer be disabled.
wireless/: Remove references to CONFIG_DISABLE_SIGNALS. Signals can no longer be disabled.
Documentation/: Remove references to CONFIG_DISABLE_SIGNALS. Signals can no longer be disabled.
include/: Remove references to CONFIG_DISABLE_SIGNALS. Signals can no longer be disabled.
drivers/: Remove references to CONFIG_DISABLE_SIGNALS. Signals can no longer be disabled.
sched/: Remove references to CONFIG_DISABLE_SIGNALS. Signals can no longer be disabled.
configs: Remove references to CONFIG_DISABLE_SIGNALS. Signals can no longer be disabled.
arch/xtensa: Remove references to CONFIG_DISABLE_SIGNALS. Signals can no longer be disabled.
arch/z80: Remove references to CONFIG_DISABLE_SIGNALS. Signals can no longer be disabled.
arch/x86: Remove references to CONFIG_DISABLE_SIGNALS. Signals can no longer be disabled.
arch/renesas and arch/risc-v: Remove references to CONFIG_DISABLE_SIGNALS. Signals can no longer be disabled.
arch/or1k: Remove all references to CONFIG_DISABLE_SIGNALS. Signals are always enabled.
arch/misoc: Remove all references to CONFIG_DISABLE_SIGNALS. Signals are always enabled.
arch/mips: Remove all references to CONFIG_DISABLE_SIGNALS. Signals are always enabled.
arch/avr: Remove all references to CONFIG_DISABLE_SIGNALS. Signals are always enabled.
arch/arm: Remove all references to CONFIG_DISABLE_SIGNALS. Signals are always enabled.
Pressl, Štěpán