if driver complete unlink ops, we need to call it to release some resource,
otherwise, it will only remove inode.
Signed-off-by: dongjiuzhu1 <dongjiuzhu1@xiaomi.com>
we can use uart to debug nuttx,like debugger:
1. read/write memory
2. Use watchpoint,breakpoint,single step.
use up_debugpoint api
3. Ctrl+c to stop, continue, or single step.
hold uart send and receive
4. register a panic event, when crash or assert/panic, we use uart to
debug.
Signed-off-by: anjiahao <anjiahao@xiaomi.com>
The BIT macro is widely used in NuttX,
and to achieve a unified strategy,
we have placed the implementation of the BIT macro
in bits.h to simplify code implementation.
Signed-off-by: hujun5 <hujun5@xiaomi.com>
It uses the memory block as the serial communication medium, which can communicate between different processes or different CPUs
Using the following configuration, the cross-core communication rate of 200MHz cortex-M55 is about 461KB/s
RAM_UART_BUFSIZE=1024
RAM_UART_POLLING_INTERVAL=100
Signed-off-by: yinshengkai <yinshengkai@xiaomi.com>
Some UART Controllers (Synopsys DesignWare 8250) will trigger spurious interrupts when the Line Control Register (LCR) is set while the UART is busy. This patch provides the option (16550_WAIT_LCR) to wait for UART until it's not busy, before setting the LCR. (16550_WAIT_LCR is disabled by default)
This patch fixes the spurious UART interrupts for the upcoming port of NuttX to StarFive JH7110 SoC (with Synopsys DesignWare 8250 UART). [The patch is explained here](https://lupyuen.github.io/articles/plic#appendix-fix-the-spurious-uart-interrupts)
drivers/serial/uart_16550.c: If 16550_WAIT_LCR is enabled, wait until UART is not busy before setting LCR
include/nuttx/serial/uart_16550.h: Define the UART Status Register (USR) for checking if UART is busy
drivers/serial/Kconfig-16550: Added option 16550_WAIT_LCR to 16550 UART Config, disabled by default
1. Update all CMakeLists.txt to adapt to new layout
2. Fix cmake build break
3. Update all new file license
4. Fully compatible with current compilation environment(use configure.sh or cmake as you choose)
------------------
How to test
From within nuttx/. Configure:
cmake -B build -DBOARD_CONFIG=sim/nsh -GNinja
cmake -B build -DBOARD_CONFIG=sim:nsh -GNinja
cmake -B build -DBOARD_CONFIG=sabre-6quad/smp -GNinja
cmake -B build -DBOARD_CONFIG=lm3s6965-ek/qemu-flat -GNinja
(or full path in custom board) :
cmake -B build -DBOARD_CONFIG=$PWD/boards/sim/sim/sim/configs/nsh -GNinja
This uses ninja generator (install with sudo apt install ninja-build). To build:
$ cmake --build build
menuconfig:
$ cmake --build build -t menuconfig
--------------------------
2. cmake/build: reformat the cmake style by cmake-format
https://github.com/cheshirekow/cmake_format
$ pip install cmakelang
$ for i in `find -name CMakeLists.txt`;do cmake-format $i -o $i;done
$ for i in `find -name *\.cmake`;do cmake-format $i -o $i;done
Co-authored-by: Matias N <matias@protobits.dev>
Signed-off-by: chao an <anchao@xiaomi.com>
Fix warning:
```
serial/ptmx.c:205:34: warning: ‘%d’ directive output may be truncated writing between 1 and 10 bytes into a region of size 8 [-Wformat-truncation=]
205 | snprintf(devname, 16, "/dev/pty%d", minor);
|
serial/ptmx.c:205:25: note: directive argument in the range [0, 2147483647]
205 | snprintf(devname, 16, "/dev/pty%d", minor);
| ^~~~~~~~~~~~
serial/ptmx.c:205:3: note: ‘snprintf’ output between 10 and 19 bytes into a destination of size 16
205 | snprintf(devname, 16, "/dev/pty%d", minor);
```
Signed-off-by: Huang Qi <huangqi3@xiaomi.com>
if multiple threads are doing serial read/write at the same time,
the driver will only wake up one of the thread, which will cause
other threads fail to be woken up in time and cause blocking
Signed-off-by: chao an <anchao@xiaomi.com>
All interrupts must be disabled to prevent re-entrancy and to prevent
interrupts from firing in the serial driver code.
Signed-off-by: hujun5 <hujun5@xiaomi.com>
At present, the serial drivers qemu_serial.c and serial_pl011.c on the fvp-v8r and qemu platforms in arm64 are duplicated
and need to be merged. The plan is to place them under the drivers\serial directory to create a common code module,
so that both fvp-v8r and qemu can use the same code.
In the future, if new platforms use pl011 serial ports, they can also be directly reused
Signed-off-by: hujun5 <hujun5@xiaomi.com>
The spawn proxy thread is a special existence in NuttX, usually some developers
spend a lot of time on stack overflow of spawn proxy thread:
https://github.com/apache/nuttx/issues/9046https://github.com/apache/nuttx/pull/9081
In order to avoid similar issues, this PR will remove spawn proxy thread to simplify
the process of task/posix_spawn().
1. Postpone the related processing of spawn file actions until after task_init()
2. Delete the temporary thread of spawn proxy and related global variables
Signed-off-by: chao an <anchao@xiaomi.com>
Align the pty behavior to linux/bsd,
Also fix the ECHO issue with microadb after https://github.com/apache/nuttx/pull/8691.
adb shell will echo normally with this patch.
Signed-off-by: Huang Qi <huangqi3@xiaomi.com>
CONFIG_SERIAL_TERMIOS only decide whether to support c_cflag field since
many terminal application need the first three fields to work correctly.
For more information please reference:
https://www.mail-archive.com/dev@nuttx.apache.org/msg09321.html
before this change(olimexino-stm32:tiny):
text data bss dec hex filename
34884 328 1768 36980 9074 nuttx
after this change:
text data bss dec hex filename
35052 340 1768 37160 9128 nuttx
delta
text data bss dec hex filename
168 12 0 180 b4 nuttx
Signed-off-by: Xiang Xiao <xiaoxiang@xiaomi.com>
There is a rookie mistake introduced by https://github.com/apache/nuttx/pull/8691,
ECHO flag is a part of Local Mode (c_lflags) instead of c_iflags.
nuttx-apps should do the same change in nsh_login and termcurse_vt100.
Signed-off-by: Huang Qi <huangqi3@xiaomi.com>
dongjiuzhu1