Zneo Serial: Fix cut'n'paste error in some conditional configuration

arch/z16/src/z16f/z16f_serial.c

@@ -255,10 +255,10 @@ static uart_dev_t g_uart1port =
 #    define UART1_ASSIGNED      1
 #else
 #  undef CONSOLE_DEV                        /* No console */
-#  if defined(CONFIG_KINETIS_UART0)
+#  if defined(CONFIG_Z16F_UART0)
 #    define TTYS0_DEV           g_uart0port /* UART0 is ttyS0 */
 #    define UART0_ASSIGNED      1
-#  elif defined(CONFIG_KINETIS_UART1)
+#  elif defined(CONFIG_Z16F_UART1)
 #    define TTYS0_DEV           g_uart1port /* UART1 is ttyS0 */
 #    define UART1_ASSIGNED      1
 #  endif
@@ -266,10 +266,10 @@ static uart_dev_t g_uart1port =
 
 /* Pick ttys1.  This could be either of UART0-1 excluding the console UART. */
 
-#if defined(CONFIG_KINETIS_UART0) && !defined(UART0_ASSIGNED)
+#if defined(CONFIG_Z16F_UART0) && !defined(UART0_ASSIGNED)
 #  define TTYS1_DEV           g_uart0port /* UART0 is ttyS1 */
 #  define UART0_ASSIGNED      1
-#elif defined(CONFIG_KINETIS_UART1) && !defined(UART1_ASSIGNED)
+#elif defined(CONFIG_Z16F_UART1) && !defined(UART1_ASSIGNED)
 #  define TTYS1_DEV           g_uart1port /* UART1 is ttyS1 */
 #  define UART1_ASSIGNED      1
 #endif
@@ -781,7 +781,10 @@ int up_putc(int ch)
   uint8_t  state;
 
   /* Keep interrupts disabled so that we do not interfere with normal
-   * driver operation
+   * driver operation.
+   *
+   * REVISIT:  I can imagine scenarios where the follow logic gets pre-empted
+   * and the the UART interrupts get left in a bad state.
    */
 
   state = z16f_disableuartirq(&CONSOLE_DEV);

configs/z16f2800100zcog/README.txt

@@ -3,6 +3,21 @@ README.txt
 
 This is the README file for the NuttX port to the ZiLog ZNEO MCU.
 
+- Console output is on UART0.
+
+- NOTE: My board has a 20MHz crystal, but I have heard of other boards with
+  18.432MHz crystals.  If you board has a diff crystal installed, then
+  modify the system frequency in include/board.h.
+
+Contents
+========
+
+  - ZDS-II Compiler Versions
+  - Patches
+  - Serial Console
+  - Selecting Configurations
+  - Configuration Sub-directories
+
 ZDS-II Compiler Versions
 ========================
 
@@ -91,6 +106,20 @@ The patch can also be removed with:
 
 See the section "Selecting Configurations" below.
 
+Serial Console
+==============
+
+By default, console output is on UART1 which corresponds to the DB9
+connector labelled CONSOLE.
+
+UART1 is also available on JP2:
+
+  MCU PIN     GPIO  JP2
+  Pin 86 TXD1 PD5   JP2 Pin 25
+  Pin 87 RXD1 PD4   JP2 Pin 25
+  Vcc               JP2 Pin 59
+  GND               JP2 Pins 19, 39, 46, 48, 56
+
 Selecting Configurations
 ========================
 
@@ -208,7 +237,7 @@ ostest
       c. At present, the native Windows build fails at the final link stages.
          The failure is due to problems in arch/z16/src/nuttx.linkcmd that
          is autogenerated by arch/z16/src/Makefile.  The basic problem
-         is the spurious spaces and and carrirage returns are generated at
+         is the spurious spaces and and carriage returns are generated at
          the end of the lines after a line continuation (\ ^M).  If these
          trailing bad characters are manually eliminated, then the build
          will succeed on the next try.