configs/nucleo-l496zg: Kconfig was copied from nucleo-144
Removed as most options have not been tested.
This commit is contained in:
Juha Niskanen
parent
92f4277b1e
commit
a7b452bc5b
|
|
@ -3,221 +3,6 @@
|
|||
# see the file kconfig-language.txt in the NuttX tools repository.
|
||||
#
|
||||
|
||||
if ARCH_BOARD_NUCLEO_144
|
||||
if ARCH_BOARD_NUCLEO_L496ZG
|
||||
|
||||
choice
|
||||
prompt "Select Console wiring."
|
||||
default NUCLEO_ARDUINO
|
||||
---help---
|
||||
Select where you will connect the console.
|
||||
|
||||
Virtual COM Port:
|
||||
|
||||
Advantage: Use the ST-Link as a console. No Extra wiring
|
||||
neded.
|
||||
|
||||
Disdvantage: Not the best choice for initial bring up.
|
||||
|
||||
ARDUINO Connector:
|
||||
|
||||
Advantage: You have a shield so it is
|
||||
easy.
|
||||
|
||||
Disdvantage: You loose the use of the
|
||||
other functions on PC6, PC7
|
||||
|
||||
STM32F7
|
||||
ARDUIONO FUNCTION GPIO
|
||||
-- ----- --------- ----
|
||||
DO RX USART6_RX PG9
|
||||
D1 TX USART6_TX PG14
|
||||
-- ----- --------- ---
|
||||
|
||||
OR
|
||||
|
||||
Morpho Connector:
|
||||
|
||||
STM32F7
|
||||
MORPHO FUNCTION GPIO
|
||||
-------- --------- -----
|
||||
CN12-64 USART8_RX PE0
|
||||
CN11-61 USART8_TX PE1
|
||||
-------- --------- -----
|
||||
|
||||
config NUCLEO_CONSOLE_ARDUINO
|
||||
bool "ARDUINO Connector"
|
||||
select STM32F7_USART6
|
||||
select USART6_SERIALDRIVER
|
||||
select USART6_SERIAL_CONSOLE
|
||||
|
||||
config NUCLEO_CONSOLE_VIRTUAL
|
||||
bool "Virtual Comport"
|
||||
select STM32F7_USART3
|
||||
select USART3_SERIALDRIVER
|
||||
select USART3_SERIAL_CONSOLE
|
||||
|
||||
config NUCLEO_CONSOLE_MORPHO
|
||||
bool "Morpho Connector"
|
||||
select STM32F7_UART8
|
||||
select UART8_SERIALDRIVER
|
||||
select UART8_SERIAL_CONSOLE
|
||||
|
||||
config NUCLEO_CONSOLE_NONE
|
||||
bool "No Console"
|
||||
|
||||
endchoice # "Select Console wiring"
|
||||
|
||||
config NUCLEO_SPI_TEST
|
||||
bool "Enable SPI test"
|
||||
default n
|
||||
---help---
|
||||
Enable Spi test - initalize and configure SPI to send
|
||||
NUCLEO_SPI_TEST_MESSAGE text. The text is sent on the
|
||||
selected SPI Buses with the configured parameters.
|
||||
Note the CS lines will not be asserted.
|
||||
|
||||
if NUCLEO_SPI_TEST
|
||||
|
||||
config NUCLEO_SPI_TEST_MESSAGE
|
||||
string "Text to Send on SPI Bus(es)"
|
||||
default "Hello World"
|
||||
depends on NUCLEO_SPI_TEST
|
||||
---help---
|
||||
Text to sent on SPI bus(es)
|
||||
|
||||
config NUCLEO_SPI1_TEST
|
||||
bool "Test SPI bus 1"
|
||||
default n
|
||||
depends on NUCLEO_SPI_TEST
|
||||
---help---
|
||||
Enable Spi test - on SPI BUS 1
|
||||
|
||||
if NUCLEO_SPI1_TEST
|
||||
|
||||
config NUCLEO_SPI1_TEST_FREQ
|
||||
int "SPI 1 Clock Freq in Hz"
|
||||
default 1000000
|
||||
depends on NUCLEO_SPI1_TEST
|
||||
---help---
|
||||
Sets SPI 1 Clock Freq
|
||||
|
||||
config NUCLEO_SPI1_TEST_BITS
|
||||
int "SPI 1 number of bits"
|
||||
default 8
|
||||
depends on NUCLEO_SPI1_TEST
|
||||
---help---
|
||||
Sets SPI 1 bit length
|
||||
|
||||
choice
|
||||
prompt "SPI BUS 1 Clock Mode"
|
||||
default NUCLEO_SPI1_TEST_MODE3
|
||||
---help---
|
||||
Sets SPI 1 clock mode
|
||||
|
||||
config NUCLEO_SPI1_TEST_MODE0
|
||||
bool "CPOL=0 CHPHA=0"
|
||||
|
||||
config NUCLEO_SPI1_TEST_MODE1
|
||||
bool "CPOL=0 CHPHA=1"
|
||||
|
||||
config NUCLEO_SPI1_TEST_MODE2
|
||||
bool "CPOL=1 CHPHA=0"
|
||||
|
||||
config NUCLEO_SPI1_TEST_MODE3
|
||||
bool "CPOL=1 CHPHA=1"
|
||||
|
||||
endchoice # "SPI BUS 1 Clock Mode"
|
||||
|
||||
endif # NUCLEO_SPI1_TEST
|
||||
|
||||
config NUCLEO_SPI2_TEST
|
||||
bool "Test SPI bus 2"
|
||||
default n
|
||||
depends on NUCLEO_SPI_TEST
|
||||
---help---
|
||||
Enable Spi test - on SPI BUS 2
|
||||
|
||||
if NUCLEO_SPI2_TEST
|
||||
|
||||
config NUCLEO_SPI2_TEST_FREQ
|
||||
int "SPI 2 Clock Freq in Hz"
|
||||
default 12000000
|
||||
depends on NUCLEO_SPI2_TEST
|
||||
---help---
|
||||
Sets SPI 2 Clock Freq
|
||||
|
||||
config NUCLEO_SPI2_TEST_BITS
|
||||
int "SPI 2 number of bits"
|
||||
default 8
|
||||
depends on NUCLEO_SPI2_TEST
|
||||
---help---
|
||||
Sets SPI 2 bit length
|
||||
|
||||
choice
|
||||
prompt "SPI BUS 2 Clock Mode"
|
||||
default NUCLEO_SPI2_TEST_MODE3
|
||||
---help---
|
||||
Sets SPI 2 clock mode
|
||||
|
||||
config NUCLEO_SPI2_TEST_MODE0
|
||||
bool "CPOL=0 CHPHA=0"
|
||||
|
||||
config NUCLEO_SPI2_TEST_MODE1
|
||||
bool "CPOL=0 CHPHA=1"
|
||||
|
||||
config NUCLEO_SPI2_TEST_MODE2
|
||||
bool "CPOL=1 CHPHA=0"
|
||||
|
||||
config NUCLEO_SPI2_TEST_MODE3
|
||||
bool "CPOL=1 CHPHA=1"
|
||||
|
||||
endchoice # "SPI BUS 2 Clock Mode"
|
||||
|
||||
endif # NUCLEO_SPI2_TEST
|
||||
|
||||
config NUCLEO_SPI3_TEST
|
||||
bool "Test SPI bus 3"
|
||||
default n
|
||||
depends on NUCLEO_SPI_TEST
|
||||
---help---
|
||||
Enable Spi test - on SPI BUS 3
|
||||
|
||||
if NUCLEO_SPI3_TEST
|
||||
|
||||
config NUCLEO_SPI3_TEST_FREQ
|
||||
int "SPI 3 Clock Freq in Hz"
|
||||
default 40000000
|
||||
depends on NUCLEO_SPI3_TEST
|
||||
---help---
|
||||
Sets SPI 3 Clock Freq
|
||||
|
||||
config NUCLEO_SPI3_TEST_BITS
|
||||
int "SPI 3 number of bits"
|
||||
default 8
|
||||
depends on NUCLEO_SPI3_TEST
|
||||
---help---
|
||||
Sets SPI 3 bit length
|
||||
|
||||
choice
|
||||
prompt "SPI BUS 3 Clock Mode"
|
||||
default NUCLEO_SPI3_TEST_MODE3
|
||||
---help---
|
||||
Sets SPI 3 clock mode
|
||||
|
||||
config NUCLEO_SPI3_TEST_MODE0
|
||||
bool "CPOL=0 CHPHA=0"
|
||||
|
||||
config NUCLEO_SPI3_TEST_MODE1
|
||||
bool "CPOL=0 CHPHA=1"
|
||||
|
||||
config NUCLEO_SPI3_TEST_MODE2
|
||||
bool "CPOL=1 CHPHA=0"
|
||||
|
||||
config NUCLEO_SPI3_TEST_MODE3
|
||||
bool "CPOL=1 CHPHA=1"
|
||||
|
||||
endchoice # "SPI BUS 3 Clock Mode"
|
||||
|
||||
endif # NUCLEO_SPI3_TEST
|
||||
endif # NUCLEO_SPI_TEST
|
||||
endif # ARCH_BOARD_NUCLEO_144
|
||||
endif # ARCH_BOARD_NUCLEO_L496ZG
|
||||
|
|
|
|||
Loading…
Reference in New Issue