diff --git a/arch/mips/src/pic32mz/pic32mz_lowconsole.c b/arch/mips/src/pic32mz/pic32mz_lowconsole.c
index c4036e3c0a..6ca3d59026 100644
--- a/arch/mips/src/pic32mz/pic32mz_lowconsole.c
+++ b/arch/mips/src/pic32mz/pic32mz_lowconsole.c
@@ -317,7 +317,7 @@ void pic32mz_consoleinit(void)
 
   /* Setup up pin selection registers for all configured UARTs.  The board.h
    * header file must provide these definitions to select the correct pin
-   * configuration for each enabled UARt.
+   * configuration for each enabled UART.
    */
 
 #ifdef CONFIG_PIC32MZ_UART1
diff --git a/arch/sparc/src/s698pm/s698pm-lowconsole.c b/arch/sparc/src/s698pm/s698pm-lowconsole.c
index 3354db3739..a0b1a08729 100644
--- a/arch/sparc/src/s698pm/s698pm-lowconsole.c
+++ b/arch/sparc/src/s698pm/s698pm-lowconsole.c
@@ -212,7 +212,7 @@ void s698pm_consoleinit(void)
 
   /* Setup up pin selection registers for all configured UARTs.  The board.h
    * header file must provide these definitions to select the correct pin
-   * configuration for each enabled UARt.
+   * configuration for each enabled UART.
    */
 
   gpreg = getreg32(S698PM_GPREG_BASE);
diff --git a/boards/arm/sama5/sama5d2-xult/README.txt b/boards/arm/sama5/sama5d2-xult/README.txt
index 4e9bf5a560..8606869d8e 100644
--- a/boards/arm/sama5/sama5d2-xult/README.txt
+++ b/boards/arm/sama5/sama5d2-xult/README.txt
@@ -72,7 +72,7 @@ REVISIT: Unverified, cloned text from the SAMA5D4-EK README.txt
 
   NuttX may be executed from SDRAM.  But this case means that the NuttX
   binary must reside on some other media (typically NAND FLASH, Serial
-  FLASH) or transferred over some interface (perhaps a UARt or even a
+  FLASH) or transferred over some interface (perhaps a UART or even a
   TFTP server).  In these cases, an intermediate bootloader such as U-Boot
   or Barebox must be used to configure the SAMA5D2 clocks and SDRAM and
   then to copy the NuttX binary into SDRAM.
diff --git a/boards/arm/sama5/sama5d4-ek/README.txt b/boards/arm/sama5/sama5d4-ek/README.txt
index 7cd86d0844..f7e385e0e2 100644
--- a/boards/arm/sama5/sama5d4-ek/README.txt
+++ b/boards/arm/sama5/sama5d4-ek/README.txt
@@ -492,7 +492,7 @@ Running NuttX from SDRAM
 
   NuttX may be executed from SDRAM.  But this case means that the NuttX
   binary must reside on some other media (typically NAND FLASH, Serial
-  FLASH) or transferred over some interface (perhaps a UARt or even a
+  FLASH) or transferred over some interface (perhaps a UART or even a
   TFTP server).  In these cases, an intermediate bootloader such as U-Boot
   or Barebox must be used to configure the SAMA5D4 clocks and SDRAM and
   then to copy the NuttX binary into SDRAM.