Add STMPE11 temperature sensor logic
git-svn-id: svn://svn.code.sf.net/p/nuttx/code/trunk@4704 42af7a65-404d-4744-a932-0658087f49c3
This commit is contained in:
patacongo
parent
30cbe29a09
commit
2f4770305f
|
|
@ -4711,7 +4711,7 @@ build
|
|||
functionality is disabled).
|
||||
</li>
|
||||
<li>
|
||||
<code>CONFIG_STMPE11_TS_DISABLE</code>:
|
||||
<code>CONFIG_STMPE11_TEMP_DISABLE</code>:
|
||||
Disable driver temperature sensor functionlaity.
|
||||
</li>
|
||||
</ul>
|
||||
|
|
|
|||
|
|
@ -804,7 +804,7 @@ defconfig -- This is a configuration file similar to the Linux
|
|||
CONFIG_STMPE11_GPIOINT_DISABLE
|
||||
Disable driver GPIO interrupt functionlality (ignored if GPIO
|
||||
functionality is disabled).
|
||||
CONFIG_STMPE11_TS_DISABLE
|
||||
CONFIG_STMPE11_TEMP_DISABLE
|
||||
Disable driver temperature sensor functionlaity.
|
||||
|
||||
Analog Devices
|
||||
|
|
|
|||
|
|
@ -58,6 +58,9 @@ endif
|
|||
ifneq ($(CONFIG_INPUT_STMPE11_ADC_DISABLE),y)
|
||||
CSRCS += stmpe11_adc.c
|
||||
endif
|
||||
ifneq ($(CONFIG_INPUT_STMPE11_TEMP_DISABLE),y)
|
||||
CSRCS += stmpe11_temp.c
|
||||
endif
|
||||
endif
|
||||
|
||||
# Include input device driver build support
|
||||
|
|
|
|||
|
|
@ -0,0 +1,174 @@
|
|||
/****************************************************************************
|
||||
* drivers/input/stmpe11_temp.c
|
||||
*
|
||||
* Copyright (C) 2012 Gregory Nutt. All rights reserved.
|
||||
* Author: Gregory Nutt <gnutt@nuttx.org>
|
||||
*
|
||||
* References:
|
||||
* "STMPE811 S-Touch® advanced resistive touchscreen controller with 8-bit
|
||||
* GPIO expander," Doc ID 14489 Rev 6, CD00186725, STMicroelectronics"
|
||||
*
|
||||
* Redistribution and use in source and binary forms, with or without
|
||||
* modification, are permitted provided that the following conditions
|
||||
* are met:
|
||||
*
|
||||
* 1. Redistributions of source code must retain the above copyright
|
||||
* notice, this list of conditions and the following disclaimer.
|
||||
* 2. Redistributions in binary form must reproduce the above copyright
|
||||
* notice, this list of conditions and the following disclaimer in
|
||||
* the documentation and/or other materials provided with the
|
||||
* distribution.
|
||||
* 3. Neither the name NuttX nor the names of its contributors may be
|
||||
* used to endorse or promote products derived from this software
|
||||
* without specific prior written permission.
|
||||
*
|
||||
* THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
|
||||
* "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
|
||||
* LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
|
||||
* FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
|
||||
* COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
|
||||
* INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
|
||||
* BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
|
||||
* OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED
|
||||
* AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
|
||||
* LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
|
||||
* ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
|
||||
* POSSIBILITY OF SUCH DAMAGE.
|
||||
*
|
||||
****************************************************************************/
|
||||
|
||||
/****************************************************************************
|
||||
* Included Files
|
||||
****************************************************************************/
|
||||
|
||||
#include <nuttx/config.h>
|
||||
|
||||
#include <assert.h>
|
||||
#include <errno.h>
|
||||
#include <debug.h>
|
||||
|
||||
#include <nuttx/input/stmpe11.h>
|
||||
|
||||
#include "stmpe11.h"
|
||||
|
||||
#if defined(CONFIG_INPUT) && defined(CONFIG_INPUT_STMPE11) && !defined(CONFIG_STMPE11_TEMP_DISABLE)
|
||||
|
||||
/****************************************************************************
|
||||
* Private Types
|
||||
****************************************************************************/
|
||||
|
||||
/****************************************************************************
|
||||
* Private Data
|
||||
****************************************************************************/
|
||||
|
||||
/****************************************************************************
|
||||
* Private Functions
|
||||
****************************************************************************/
|
||||
|
||||
/****************************************************************************
|
||||
* Public Functions
|
||||
****************************************************************************/
|
||||
|
||||
/****************************************************************************
|
||||
* Name: stmpe11_tempinitialize
|
||||
*
|
||||
* Description:
|
||||
* Configure the temperature sensor.
|
||||
*
|
||||
* Input Parameters:
|
||||
* handle - The handle previously returned by stmpe11_instantiate
|
||||
*
|
||||
* Returned Value:
|
||||
* Zero is returned on success. Otherwise, a negated errno value is
|
||||
* returned to indicate the nature of the failure.
|
||||
*
|
||||
****************************************************************************/
|
||||
|
||||
int stmpe11_tempinitialize(STMPE11_HANDLE handle)
|
||||
{
|
||||
FAR struct stmpe11_dev_s *priv = (FAR struct stmpe11_dev_s *)handle;
|
||||
uint8_t regval;
|
||||
|
||||
/* Enable clocking for ADC and the temperature sensor */
|
||||
|
||||
regval = stmpe11_getreg8(priv, STMPE11_SYS_CTRL2);
|
||||
regval &= ~(SYS_CTRL2_TS_OFF | SYS_CTRL2_ADC_OFF);
|
||||
stmpe11_putreg8(priv, STMPE11_SYS_CTRL2, regval);
|
||||
|
||||
/* Enable the temperature sensor */
|
||||
|
||||
stmpe11_putreg8(priv, STMPE11_TEMP_CTRL, TEMP_CTRL_ENABLE);
|
||||
|
||||
/* Aquire data enable */
|
||||
|
||||
stmpe11_putreg8(priv, STMPE11_TEMP_CTRL, (TEMP_CTRL_ACQ|TEMP_CTRL_ENABLE));
|
||||
|
||||
return OK;
|
||||
}
|
||||
|
||||
/****************************************************************************
|
||||
* Name: stmpe11_tempread
|
||||
*
|
||||
* Description:
|
||||
* Configure the temperature sensor.
|
||||
*
|
||||
* Input Parameters:
|
||||
* handle - The handle previously returned by stmpe11_instantiate
|
||||
*
|
||||
* Returned Value:
|
||||
* Zero is returned on success. Otherwise, a negated errno value is
|
||||
* returned to indicate the nature of the failure.
|
||||
*
|
||||
****************************************************************************/
|
||||
|
||||
uint16_t stmpe11_tempread(STMPE11_HANDLE handle)
|
||||
{
|
||||
FAR struct stmpe11_dev_s *priv = (FAR struct stmpe11_dev_s *)handle;
|
||||
uint32_t temp = 0;
|
||||
uint8_t temp1;
|
||||
uint8_t temp2;
|
||||
|
||||
/* Acquire data enable */
|
||||
|
||||
stmpe11_putreg8(priv, STMPE11_TEMP_CTRL, (TEMP_CTRL_ACQ|TEMP_CTRL_ENABLE));
|
||||
|
||||
/* Read the tempreature */
|
||||
|
||||
temp1 = stmpe11_getreg8(priv, STMPE11_SYS_CTRL2);
|
||||
temp2 = stmpe11_getreg8(priv, STMPE11_SYS_CTRL2+1);
|
||||
|
||||
/* Scale the tempreature */
|
||||
|
||||
temp = ((uint32_t)(temp1 & 3) << 8) | temp2;
|
||||
temp = (uint32_t)((33 * temp * 100) / 751);
|
||||
temp = (uint32_t)((temp + 5) / 10);
|
||||
|
||||
return (uint16_t)temp;
|
||||
}
|
||||
|
||||
/****************************************************************************
|
||||
* Name: stmpe11_tempinterrupt
|
||||
*
|
||||
* Description:
|
||||
* Configure the temperature sensor to sample the temperature periodically.
|
||||
* Set the temperature threshold to generate an interrupt and notify
|
||||
* to the client using the provide callback function pointer.
|
||||
*
|
||||
* Input Parameters:
|
||||
* handle - The handle previously returned by stmpe11_instantiate
|
||||
* threshold - The threshold temperature value
|
||||
* direction - True: Generate an interrupt if the temperate exceeds the
|
||||
* threshold value; False: Generate an interrupt if the
|
||||
* temperature falls below the threshold value.
|
||||
* callback - The client callback function that will be called when
|
||||
* the termperature crosses the threshold.
|
||||
*
|
||||
* Returned Value:
|
||||
* Zero is returned on success. Otherwise, a negated errno value is
|
||||
* returned to indicate the nature of the failure.
|
||||
*
|
||||
****************************************************************************/
|
||||
/* Not implemented */
|
||||
|
||||
#endif /* CONFIG_INPUT && CONFIG_INPUT_STMPE11 && !CONFIG_STMPE11_TEMP_DISABLE */
|
||||
|
||||
|
|
@ -80,7 +80,7 @@
|
|||
* CONFIG_STMPE11_GPIOINT_DISABLE
|
||||
* Disable driver GPIO interrupt functionlality (ignored if GPIO functionality is
|
||||
* disabled).
|
||||
* CONFIG_STMPE11_TS_DISABLE
|
||||
* CONFIG_STMPE11_TEMP_DISABLE
|
||||
* Disable driver temperature sensor functionlaity.
|
||||
*/
|
||||
|
||||
|
|
@ -693,6 +693,64 @@ EXTERN int stmpe11_adcconfig(STMPE11_HANDLE handle, int pin);
|
|||
EXTERN uint16_t stmpe11_adcread(STMPE11_HANDLE handle, int pin);
|
||||
#endif
|
||||
|
||||
/********************************************************************************************
|
||||
* Name: stmpe11_tempinitialize
|
||||
*
|
||||
* Description:
|
||||
* Configure the temperature sensor.
|
||||
*
|
||||
* Input Parameters:
|
||||
* handle - The handle previously returned by stmpe11_instantiate
|
||||
*
|
||||
* Returned Value:
|
||||
* Zero is returned on success. Otherwise, a negated errno value is returned to indicate
|
||||
* the nature of the failure.
|
||||
*
|
||||
********************************************************************************************/
|
||||
|
||||
EXTERN int stmpe11_tempinitialize(STMPE11_HANDLE handle);
|
||||
|
||||
/********************************************************************************************
|
||||
* Name: stmpe11_tempread
|
||||
*
|
||||
* Description:
|
||||
* Configure the temperature sensor.
|
||||
*
|
||||
* Input Parameters:
|
||||
* handle - The handle previously returned by stmpe11_instantiate
|
||||
*
|
||||
* Returned Value:
|
||||
* Zero is returned on success. Otherwise, a negated errno value is returned to indicate
|
||||
* the nature of the failure.
|
||||
*
|
||||
********************************************************************************************/
|
||||
|
||||
EXTERN uint16_t stmpe11_tempread(STMPE11_HANDLE handle);
|
||||
|
||||
/********************************************************************************************
|
||||
* Name: stmpe11_tempinterrupt
|
||||
*
|
||||
* Description:
|
||||
* Configure the temperature sensor to sample the temperature periodically.
|
||||
* Set the temperature threshold to generate an interrupt and notify
|
||||
* to the client using the provide callback function pointer.
|
||||
*
|
||||
* Input Parameters:
|
||||
* handle - The handle previously returned by stmpe11_instantiate
|
||||
* threshold - The threshold temperature value
|
||||
* direction - True: Generate an interrupt if the temperate exceeds the
|
||||
* threshold value; False: Generate an interrupt if the
|
||||
* temperature falls below the threshold value.
|
||||
* callback - The client callback function that will be called when
|
||||
* the termperature crosses the threshold.
|
||||
*
|
||||
* Returned Value:
|
||||
* Zero is returned on success. Otherwise, a negated errno value is returned to indicate
|
||||
* the nature of the failure.
|
||||
*
|
||||
********************************************************************************************/
|
||||
/* Not implemented */
|
||||
|
||||
#undef EXTERN
|
||||
#ifdef __cplusplus
|
||||
}
|
||||
|
|
|
|||
Loading…
Reference in New Issue