LPC17xx Kconfig looks good

git-svn-id: svn://svn.code.sf.net/p/nuttx/code/trunk@5099 42af7a65-404d-4744-a932-0658087f49c3

arch/arm/Kconfig

@@ -142,7 +142,7 @@ config ARCH_CHIP
 	default "imx"		if ARCH_CHIP_IMX
 	default "kinetis"	if ARCH_CHIP_KINETIS
 	default "lm3s"		if ARCH_CHIP_LM3S
-	default "lpc17x"	if ARCH_CHIP_LPC17XX
+	default "lpc17xx"	if ARCH_CHIP_LPC17XX
 	default "lpc214x"	if ARCH_CHIP_LPC214X
 	default "lpc2378"	if ARCH_CHIP_LPC2378
 	default "lpc31xx"	if ARCH_CHIP_LPC31XX
@@ -171,7 +171,7 @@ config ARCH_IRQPRIO
 	---help---
 		Select if your board supports interrupt prioritization.
 
-config ARCH_LOOPSPERMSEC
+config BOARD_LOOPSPERMSEC
 	int "Delay loops per millisecond"
 	default 5000
 	---help---
@@ -183,8 +183,8 @@ config ARCH_CALIBRATION
 	---help---
 		Enables some built in instrumentation that causes a 100 second delay
 		during boot-up.  This 100 second delay serves no purpose other than it
-		allows you to calibratre ARCH_LOOPSPERMSEC.  You simply use a stop
-		watch to measure the 100 second delay then adjust ARCH_LOOPSPERMSEC until
+		allows you to calibratre BOARD_LOOPSPERMSEC.  You simply use a stop
+		watch to measure the 100 second delay then adjust BOARD_LOOPSPERMSEC until
 		the delay actually is 100 seconds.
 
 if ARCH_CHIP_C5471

arch/arm/src/lpc17xx/Kconfig

@@ -54,6 +54,31 @@ config ARCH_FAMILY_LPC176X
 	bool
 	default y if ARCH_CHIP_LPC1764 || ARCH_CHIP_LPC1765 || ARCH_CHIP_LPC1766 || ARCH_CHIP_LPC1767 || ARCH_CHIP_LPC1768 || ARCH_CHIP_LPC1769
 
+choice
+	prompt "Toolchain Selection"
+	default LPC17_CODESOURCERYW
+	depends on ARCH_CHIP_LPC17XX
+
+config LPC17_CODESOURCERYW
+	bool "CodeSourcery for Windows"
+
+config LPC17_CODESOURCERYL
+	bool "CodeSourcery for Linux"
+
+config LPC17_DEVKITARM
+	bool "DevkitARM (Windows)"
+
+config LPC17_BUILDROOT
+	bool "NuttX buildroot (Cygwin or Linux)"
+
+config LPC17_CODEREDW
+	bool "CodeRed for Windows"
+
+config LPC17_CODEREDL
+	bool "CodeRed for Windows"
+
+endchoice
+
 menu "LPC17xx Peripheral Support"
 
 config LPC17_MAINOSC
@@ -290,7 +315,7 @@ config CAN2_BAUD
 	int "CAN2 BAUD"
 	depends on LPC17_CAN2
 	---help---
-		CAN2 BAUD rate.  Required if CONFIG_LPC17_CAN2 is defined.
+		CAN2 BAUD rate.  Required if LPC17_CAN2 is defined.
 
 config CAN1_DIVISOR
 	int "CAN1 CCLK divisor"
@@ -345,7 +370,7 @@ config CAN_REGDEBUG
 
 endmenu
 
-config CONFIG_GPIO_IRQ
+config GPIO_IRQ
 	bool "GPIO interrupt support"
 	default n
 	---help---

arch/mips/Kconfig

@@ -47,7 +47,7 @@ config ARCH_IRQPRIO
 	---help---
 		Select if your board supports interrupt prioritization.
 
-config ARCH_LOOPSPERMSEC
+config BOARD_LOOPSPERMSEC
 	int "Delay loops per millisecond"
 	default 5000
 	---help---
@@ -59,8 +59,8 @@ config ARCH_CALIBRATION
 	---help---
 		Enables some built in instrumentation that causes a 100 second delay
 		during boot-up.  This 100 second delay serves no purpose other than it
-		allows you to calibratre ARCH_LOOPSPERMSEC.  You simply use a stop
-		watch to measure the 100 second delay then adjust ARCH_LOOPSPERMSEC until
+		allows you to calibratre BOARD_LOOPSPERMSEC.  You simply use a stop
+		watch to measure the 100 second delay then adjust BOARD_LOOPSPERMSEC until
 		the delay actually is 100 seconds.
 
 source arch/mips/src/common/Kconfig

drivers/Kconfig

@@ -11,7 +11,7 @@ config DEV_NULL
 
 config DEV_ZERO
 	bool "Enable /dev/zero"
-	default y
+	default n
 
 config LOOP
 	bool "Enable loop device"
@@ -86,7 +86,7 @@ endif
 
 config I2C
 	bool "I2C support"
-	default y
+	default n
 	---help---
 		This selection enables building of the "upper-half" I2C driver.
 		See include/nuttx/i2c.h for further I2C driver information.
@@ -96,7 +96,7 @@ endif
 
 config SPI
 	bool "SPI support"
-	default y
+	default n
 	---help---
 		This selection enables building of the "upper-half" SPI driver.
 		See include/nuttx/spi.h for further SPI driver information.
@@ -128,7 +128,7 @@ endif
 
 config WATCHDOG
 	bool "Watchdog timer support"
-	default y
+	default n
 	---help---
 		This selection enables building of the "upper-half" watchdog timer driver.
 		See include/nuttx/watchdog.h for further watchdog timer driver information.
@@ -164,7 +164,7 @@ endif
 
 menuconfig INPUT
 	bool "Input device support"
-	default y
+	default n
 	---help---
 		This directory holds implementations of input device drivers.
 		This includes such things as touchscreen and keypad drivers.