# SPDX-License-Identifier: BSD-3-Clause

mainmenu "SOF $(PROJECTVERSION) Configuration"

comment "Compiler: $(CC_VERSION_TEXT)"

menu "CAVS"
	depends on CAVS

config HP_MEMORY_BANKS
	int "HP memory banks count"
	default 8
	help
	  Available memory banks count for High Performance memory
	  Lowering available banks could result in lower power consumption
	  Too low count should result in unresponsive/crashing image due to not
	  enough space for FW base image
	  Banks are 64kb in size.

config LP_MEMORY_BANKS
	int "LP memory banks count"
	default 1
	depends on LP_SRAM
	help
	  Available memory banks count for Low Power memory

config LP_SRAM
	bool "Enable LPSRAM memory"
	default n
	help
	  Turn ON/OFF LPSRAM bank/s. This provides an option to enable an LPSRAM
	  memory for specific platform. Until this options is enabled firmware will
	  not enable any of LPSRAM memory banks.

config WAITI_DELAY
	bool "Enable delay before WAITI instruction"
	default n
	help
	  Some cAVS platforms may require additional delay to flush loads
	  and stores before entering WAITI.

endmenu

config HOST_PTABLE
	bool
	default n

config BOOT_LOADER
	bool
	default n

config HAVE_RESET_VECTOR_ROM
	bool
	default n
	help
	  Select if your platform has the reset vector
	  in ROM.

config IRQ_MAP
	bool
	default n

config DMA_GW
	bool
	default n

config MEM_WND
	bool
	default n

config INTEL_IOMUX
	bool
	default n

config HW_LLI
	bool
	default n
	help
	  Hardware linked list is the DW-DMA feature, which allows
	  to automatically reload the next programmed linked list
	  item from memory without stopping the transfer. Without
	  it the transfer stops after every lli read and FW needs
	  to manually setup the next transfer.

	  Any platforms with hardware linked list support
	  should set this.

config DW_DMA_AGGREGATED_IRQ
	bool
	default n
	help
	  Some platforms cannot register interrupt per DW-DMA channel
	  and have the possibility only to register interrupts per
	  DMA controller, which require manual handling of aggregated
	  irq.

	  Any platforms with DW-DMA aggregated interrupts support
	  should set this.

config DMA_SUSPEND_DRAIN
	bool
	default n
	help
	  Some platforms cannot just simple disable DMA
	  channel during the transfer, because it will
	  hang the whole DMA controller. Instead we can
	  suspend the channel and drain the FIFO in order
	  to stop the channel as soon as possible.

	  Any platforms without the ability to disable
	  the DMA channel right away should set this.

config DMA_FIFO_PARTITION
	bool
	default n
	help
	  Some platforms require to manually set DMA
	  FIFO partitions before starting any transfer.

	  Any platforms without automatic FIFO partitions
	  should set this.

config INTERRUPT_LEVEL_1
	bool
	default n
	help
	  Select if the platform supports any interrupts of level 1.
	  Disabling this option allows for less memory consumption.

config INTERRUPT_LEVEL_2
	bool
	default n
	help
	  Select if the platform supports any interrupts of level 2.
	  Disabling this option allows for less memory consumption.

config INTERRUPT_LEVEL_3
	bool
	default n
	help
	  Select if the platform supports any interrupts of level 3.
	  Disabling this option allows for less memory consumption.

config INTERRUPT_LEVEL_4
	bool
	default n
	help
	  Select if the platform supports any interrupts of level 4.
	  Disabling this option allows for less memory consumption.

config INTERRUPT_LEVEL_5
	bool
	default n
	help
	  Select if the platform supports any interrupts of level 5.
	  Disabling this option allows for less memory consumption.

source "src/Kconfig"

menu "Debug"

config DEBUG
	bool "Enable debug build"
	default n
	help
	  Select for debug build

config GDB_DEBUG
	bool "GDB Stub"
	default n
	help
	  Select for GDB debugging

config DEBUG_HEAP
	bool "Heap debug"
	default n
	help
	  Select for enable heap alloc debugging

config DEBUG_BLOCK_FREE
	bool "Blocks freeing debug"
	default n
	help
	  It enables checking if free was called multiple times on
	  already freed block of memory. Enabling this feature increases
	  number of memory writes and reads, due to checks for memory patterns
	  that may be performed on allocation and deallocation.

config DEBUG_LOCKS
	bool "Spinlock debug"
	default n
	help
	  It adds additional information to the spinlocks about
	  the current user of the lock. Also executes panic
	  on deadlock.

config DEBUG_LOCKS_VERBOSE
	bool "Spinlock verbose debug"
	depends on DEBUG_LOCKS
	default n
	help
	  In addition to DEBUG_LOCKS it also adds spinlock traces
	  every time the lock is acquired.

config BUILD_VM_ROM
	bool "Build VM ROM"
	default n
	help
	  Select if you want to build VM ROM

config DEBUG_IPC_COUNTERS
	bool "IPC counters"
	depends on CAVS
	depends on DEBUG
	default n
	help
	  Select for enabling tracing IPC counter in SRAM_REG mailbox

endmenu