function example_spk_eq() %% Design an example speaker equalizer with the provided sample data % This equalizer by default uses a FIR and IIR components those should be % both in the speaker pipeline. % % Note that IIR should be first since the included band-pass response provides % signal headroom. %% % Copyright (c) 2016, Intel Corporation % All rights reserved. % % Redistribution and use in source and binary forms, with or without % modification, are permitted provided that the following conditions are met: % * Redistributions of source code must retain the above copyright % notice, this list of conditions and the following disclaimer. % * Redistributions in binary form must reproduce the above copyright % notice, this list of conditions and the following disclaimer in the % documentation and/or other materials provided with the distribution. % * Neither the name of the Intel Corporation nor the % names of its contributors may be used to endorse or promote products % derived from this software without specific prior written permission. % % THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" % AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE % IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE % ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT OWNER OR CONTRIBUTORS BE % LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR % CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF % SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS % INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN % CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) % ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE % POSSIBILITY OF SUCH DAMAGE. % % Author: Seppo Ingalsuo % %% Get defaults for equalizer design eq = eq_defaults(); %% Settings for this EQ eq.fs = 48e3; % Default sample rate in SOF eq.enable_fir = 1; % Try enabling and disabling FIR part eq.enable_iir = 1; % Try enabling and disabling IIR part eq.norm_type = 'peak'; % Scale filters to have peak at 0 dB eq.norm_offs_db = 0; % Can be used to control gain eq.p_fmin = 100; % With this data start plots from 100 Hz eq.p_fmax = 20e3; % and end to 20 kHz. %% Get acousticial frequency response measurement data. This is % a quite typical response for a miniature speaker. Alternatively % the response could be read from spreadsheet column format that is % commonly supported by audio measurement equipment. Then extract % the frequency and magnitude columns. E.g. % % data = xlsread('spkr.xlsx', 1, 'A5:B78'); % eq.raw_f = data(:,1); % eq.raw_m_db = data(:,2); eq.raw_f = [ ... 298.533, 316.232, 334.971, 354.813, 375.838, 398.106, ... 421.699, 446.685, 473.153, 501.186, 530.887, 562.342, ... 595.663, 630.958, 668.345, 707.946, 749.895, 794.329, ... 841.397, 891.252, 944.062, 1000, 1059.26, 1122.02, ... 1188.5, 1258.93, 1333.52, 1412.54, 1496.24, 1584.9, ... 1678.81, 1778.28, 1883.65, 1995.27, 2113.49, 2238.72, ... 2371.38, 2511.89, 2660.73, 2818.39, 2985.39, 3162.28, ... 3349.66, 3548.14, 3758.38, 3981.08, 4216.97, 4466.84, ... 4731.52, 5011.88, 5308.85, 5623.42, 5956.63, 6309.58, ... 6683.45, 7079.47, 7498.95, 7943.3, 8413.97, 8912.52, ... 9440.62, 10000, 10592.6, 11220.2, 11885, 12589.3, ... 13335.2, 14125.4, 14962.4, 15849, 16788.1, 17782.8, ... 18836.5, 19952.7 ... ]; eq.raw_m_db = [ ... 58.1704, 60.074, 60.4541, 61.3079, 62.8198, 64.3749, ... 65.1556, 66.512, 67.5916, 68.6344, 69.9276, 70.7658, ... 71.1125, 72.0627, 73.5348, 75.4887, 77.3088, 79.1541, ... 80.9627, 82.0607, 81.943, 81.2228, 81.9497, 83.1848, ... 84.3375, 85.4993, 86.4642, 87.1179, 87.4424, 87.53, ... 85.7425, 85.0095, 82.9405, 82.9242, 82.7327, 83.6423, ... 83.2839, 82.4201, 84.1403, 84.6485, 83.9274, 83.3366, ... 83.3005, 84.2598, 85.1544, 86.015, 86.6519, 87.2118, ... 87.5498, 88.1742, 88.5215, 88.3801, 89.8762, 91.4418, ... 93.1845, 94.3355, 95.0918, 95.0258, 94.0337, 91.1068, ... 88.7303, 87.4853, 86.2916, 83.037, 79.8056, 78.2022, ... 76.0341, 74.5674, 69.2288, 56.1308, 68.697, 69.687, ... 68.0005, 64.698 ... ]; %% With parametric IIR EQ try to place peaking EQ at % resonant frequencies 1.4 kHz and 7.5 kHz. The gain % and Q values were experimented manually. Additionally % The lowest and highest frequeciens below and above speaker % capability are attenuated with high-pass and low-pass % filtering. if eq.enable_iir; eq.peq = [ ... eq.PEQ_HP2 100 NaN NaN; ... eq.PEQ_PN2 1480 -7 2.0; ... eq.PEQ_PN2 7600 -11 1.3; ... eq.PEQ_LP2 14500 NaN NaN; ... ]; end %% With FIR EQ try to flatten frequency response within % 1 - 13 kHz frequency band. if eq.enable_fir eq.fir_minph = 1; eq.fir_beta = 4; eq.fir_length = 63; eq.fir_autoband = 0; eq.fmin_fir = 900; eq.fmax_fir = 10700; end %% Design EQ eq = eq_compute(eq); %% Plot eq_plot(eq, 1); %% Export FIR part channels_in_config = 2; % Identical two speakers assign_response = [0 0]; % Switch to response #0 num_responses = 1; % Single response if eq.enable_fir bq_fir = eq_fir_blob_quant(eq.b_fir); bm_fir = eq_fir_blob_merge(channels_in_config, ... num_responses, ... assign_response, ... [ bq_fir ]); bp_fir = eq_fir_blob_pack(bm_fir); eq_alsactl_write('example_spk_eq_fir.txt', bp_fir); eq_blob_write('example_spk_eq_fir.blob', bp_fir); eq_tplg_write('example_spk_eq_fir.m4', bp_fir, 'FIR'); end %% Export IIR part if eq.enable_iir bq_iir = eq_iir_blob_quant(eq.p_z, eq.p_p, eq.p_k); bm_iir = eq_iir_blob_merge(channels_in_config, ... num_responses, ... assign_response, ... [ bq_iir ]); bp_iir = eq_iir_blob_pack(bm_iir); eq_alsactl_write('example_spk_eq_iir.txt', bp_iir); eq_blob_write('example_spk_eq_iir.blob', bp_iir); eq_tplg_write('example_spk_eq_iir.m4', bp_iir, 'IIR'); end end