OrgACRN
/
acrn-kernel
mirror of https://github.com/projectacrn/acrn-kernel.git
1
0
Fork 0
Code Issues Releases Wiki Activity
acrn-kernel/arch/avr32/boards/atstk1000/atstk1002.c

335 lines
7.8 KiB
C
Raw Blame History

/*
* ATSTK1002/ATSTK1006 daughterboard-specific init code
*
* Copyright (C) 2005-2007 Atmel Corporation
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License version 2 as
* published by the Free Software Foundation.
*/
#include <linux/clk.h>
#include <linux/etherdevice.h>
#include <linux/init.h>
#include <linux/kernel.h>
#include <linux/platform_device.h>
#include <linux/string.h>
#include <linux/types.h>
#include <linux/spi/spi.h>
#include <linux/spi/at73c213.h>
#include <linux/atmel-mci.h>
#include <video/atmel_lcdc.h>
#include <asm/io.h>
#include <asm/setup.h>
#include <mach/at32ap700x.h>
#include <mach/board.h>
#include <mach/init.h>
#include <mach/portmux.h>
#include "atstk1000.h"
/* Oscillator frequencies. These are board specific */
unsigned long at32_board_osc_rates[3] = {
[0] = 32768, /* 32.768 kHz on RTC osc */
[1] = 20000000, /* 20 MHz on osc0 */
[2] = 12000000, /* 12 MHz on osc1 */
};
/*
* The ATSTK1006 daughterboard is very similar to the ATSTK1002. Both
* have the AT32AP7000 chip on board; the difference is that the
* STK1006 has 128 MB SDRAM (the STK1002 uses the 8 MB SDRAM chip on
* the STK1000 motherboard) and 256 MB NAND flash (the STK1002 has
* none.)
*
* The RAM difference is handled by the boot loader, so the only
* difference we end up handling here is the NAND flash.
*/
#ifdef CONFIG_BOARD_ATSTK1006
#include <linux/mtd/partitions.h>
#include <mach/smc.h>
static struct smc_timing nand_timing __initdata = {
.ncs_read_setup = 0,
.nrd_setup = 10,
.ncs_write_setup = 0,
.nwe_setup = 10,
.ncs_read_pulse = 30,
.nrd_pulse = 15,
.ncs_write_pulse = 30,
.nwe_pulse = 15,
.read_cycle = 30,
.write_cycle = 30,
.ncs_read_recover = 0,
.nrd_recover = 15,
.ncs_write_recover = 0,
/* WE# high -> RE# low min 60 ns */
.nwe_recover = 50,
};
static struct smc_config nand_config __initdata = {
.bus_width = 1,
.nrd_controlled = 1,
.nwe_controlled = 1,
.nwait_mode = 0,
.byte_write = 0,
.tdf_cycles = 2,
.tdf_mode = 0,
};
static struct mtd_partition nand_partitions[] = {
{
.name = "main",
.offset = 0x00000000,
.size = MTDPART_SIZ_FULL,
},
};
static struct mtd_partition *nand_part_info(int size, int *num_partitions)
{
*num_partitions = ARRAY_SIZE(nand_partitions);
return nand_partitions;
}
static struct atmel_nand_data atstk1006_nand_data __initdata = {
.cle = 21,
.ale = 22,
.rdy_pin = GPIO_PIN_PB(30),
.enable_pin = GPIO_PIN_PB(29),
.partition_info = nand_part_info,
};
#endif
struct eth_addr {
u8 addr[6];
};
static struct eth_addr __initdata hw_addr[2];
static struct eth_platform_data __initdata eth_data[2] = {
{
/*
* The MDIO pullups on STK1000 are a bit too weak for
* the autodetection to work properly, so we have to
* mask out everything but the correct address.
*/
.phy_mask = ~(1U << 16),
},
{
.phy_mask = ~(1U << 17),
},
};
#ifdef CONFIG_BOARD_ATSTK1000_EXTDAC
static struct at73c213_board_info at73c213_data = {
.ssc_id = 0,
.shortname = "AVR32 STK1000 external DAC",
};
#endif
#ifndef CONFIG_BOARD_ATSTK100X_SW1_CUSTOM
static struct spi_board_info spi0_board_info[] __initdata = {
#ifdef CONFIG_BOARD_ATSTK1000_EXTDAC
{
/* AT73C213 */
.modalias = "at73c213",
.max_speed_hz = 200000,
.chip_select = 0,
.mode = SPI_MODE_1,
.platform_data = &at73c213_data,
},
#endif
{
/* QVGA display */
.modalias = "ltv350qv",
.max_speed_hz = 16000000,
.chip_select = 1,
.mode = SPI_MODE_3,
},
};
#endif
#ifdef CONFIG_BOARD_ATSTK100X_SPI1
static struct spi_board_info spi1_board_info[] __initdata = { {
/* patch in custom entries here */
} };
#endif
/*
* The next two functions should go away as the boot loader is
* supposed to initialize the macb address registers with a valid
* ethernet address. But we need to keep it around for a while until
* we can be reasonably sure the boot loader does this.
*
* The phy_id is ignored as the driver will probe for it.
*/
static int __init parse_tag_ethernet(struct tag *tag)
{
int i;
i = tag->u.ethernet.mac_index;
if (i < ARRAY_SIZE(hw_addr))
memcpy(hw_addr[i].addr, tag->u.ethernet.hw_address,
sizeof(hw_addr[i].addr));
return 0;
}
__tagtable(ATAG_ETHERNET, parse_tag_ethernet);
static void __init set_hw_addr(struct platform_device *pdev)
{
struct resource *res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
const u8 *addr;
void __iomem *regs;
struct clk *pclk;
if (!res)
return;
if (pdev->id >= ARRAY_SIZE(hw_addr))
return;
addr = hw_addr[pdev->id].addr;
if (!is_valid_ether_addr(addr))
return;
/*
* Since this is board-specific code, we'll cheat and use the
* physical address directly as we happen to know that it's
* the same as the virtual address.
*/
regs = (void __iomem __force *)res->start;
pclk = clk_get(&pdev->dev, "pclk");
if (!pclk)
return;
clk_enable(pclk);
__raw_writel((addr[3] << 24) | (addr[2] << 16)
| (addr[1] << 8) | addr[0], regs + 0x98);
__raw_writel((addr[5] << 8) | addr[4], regs + 0x9c);
clk_disable(pclk);
clk_put(pclk);
}
#ifdef CONFIG_BOARD_ATSTK1000_EXTDAC
static void __init atstk1002_setup_extdac(void)
{
struct clk *gclk;
struct clk *pll;
gclk = clk_get(NULL, "gclk0");
if (IS_ERR(gclk))
goto err_gclk;
pll = clk_get(NULL, "pll0");
if (IS_ERR(pll))
goto err_pll;
if (clk_set_parent(gclk, pll)) {
pr_debug("STK1000: failed to set pll0 as parent for DAC clock\n");
goto err_set_clk;
}
at32_select_periph(GPIO_PIOA_BASE, (1 << 30), GPIO_PERIPH_A, 0);
at73c213_data.dac_clk = gclk;
err_set_clk:
clk_put(pll);
err_pll:
clk_put(gclk);
err_gclk:
return;
}
#else
static void __init atstk1002_setup_extdac(void)
{
}
#endif /* CONFIG_BOARD_ATSTK1000_EXTDAC */
void __init setup_board(void)
{
#ifdef CONFIG_BOARD_ATSTK100X_SW2_CUSTOM
at32_map_usart(0, 1); /* USART 0/B: /dev/ttyS1, IRDA */
#else
at32_map_usart(1, 0); /* USART 1/A: /dev/ttyS0, DB9 */
#endif
/* USART 2/unused: expansion connector */
at32_map_usart(3, 2); /* USART 3/C: /dev/ttyS2, DB9 */
at32_setup_serial_console(0);
}
#ifndef CONFIG_BOARD_ATSTK100X_SW2_CUSTOM
static struct mci_platform_data __initdata mci0_data = {
.slot[0] = {
.bus_width = 4,
/* MMC card detect requires MACB0 *NOT* be used */
#ifdef CONFIG_BOARD_ATSTK1002_SW6_CUSTOM
.detect_pin = GPIO_PIN_PC(14), /* gpio30/sdcd */
.wp_pin = GPIO_PIN_PC(15), /* gpio31/sdwp */
#else
.detect_pin = -ENODEV,
.wp_pin = -ENODEV,
#endif /* SW6 for sd{cd,wp} routing */
},
};
#endif /* SW2 for MMC signal routing */
static int __init atstk1002_init(void)
{
/*
* ATSTK1000 uses 32-bit SDRAM interface. Reserve the
* SDRAM-specific pins so that nobody messes with them.
*/
at32_reserve_pin(GPIO_PIOE_BASE, ATMEL_EBI_PE_DATA_ALL);
#ifdef CONFIG_BOARD_ATSTK1006
smc_set_timing(&nand_config, &nand_timing);
smc_set_configuration(3, &nand_config);
at32_add_device_nand(0, &atstk1006_nand_data);
#endif
#ifdef CONFIG_BOARD_ATSTK100X_SW2_CUSTOM
at32_add_device_usart(1);
#else
at32_add_device_usart(0);
#endif
at32_add_device_usart(2);
#ifndef CONFIG_BOARD_ATSTK1002_SW6_CUSTOM
set_hw_addr(at32_add_device_eth(0, &eth_data[0]));
#endif
#ifndef CONFIG_BOARD_ATSTK100X_SW1_CUSTOM
at32_add_device_spi(0, spi0_board_info, ARRAY_SIZE(spi0_board_info));
#endif
#ifdef CONFIG_BOARD_ATSTK100X_SPI1
at32_add_device_spi(1, spi1_board_info, ARRAY_SIZE(spi1_board_info));
#endif
#ifndef CONFIG_BOARD_ATSTK100X_SW2_CUSTOM
at32_add_device_mci(0, &mci0_data);
#endif
#ifdef CONFIG_BOARD_ATSTK1002_SW5_CUSTOM
set_hw_addr(at32_add_device_eth(1, &eth_data[1]));
#else
at32_add_device_lcdc(0, &atstk1000_lcdc_data,
fbmem_start, fbmem_size,
ATMEL_LCDC_PRI_24BIT | ATMEL_LCDC_PRI_CONTROL);
#endif
at32_add_device_usba(0, NULL);
#ifndef CONFIG_BOARD_ATSTK100X_SW3_CUSTOM
at32_add_device_ssc(0, ATMEL_SSC_TX);
#endif
atstk1000_setup_j2_leds();
atstk1002_setup_extdac();
return 0;
}
postcore_initcall(atstk1002_init);
Reference in New Issue View Git Blame Copy Permalink