acrn-kernel/arch/arc/boot/dts/axc003_idu.dtsi

168 lines
3.9 KiB
Plaintext

// SPDX-License-Identifier: GPL-2.0-only
/*
* Copyright (C) 2014, 2015 Synopsys, Inc. (www.synopsys.com)
*/
/*
* Device tree for AXC003 CPU card: HS38x2 (Dual Core) with IDU intc
*/
/include/ "skeleton_hs_idu.dtsi"
/ {
compatible = "snps,arc";
#address-cells = <2>;
#size-cells = <2>;
cpu_card {
compatible = "simple-bus";
#address-cells = <1>;
#size-cells = <1>;
ranges = <0x00000000 0x0 0xf0000000 0x10000000>;
input_clk: input-clk {
#clock-cells = <0>;
compatible = "fixed-clock";
clock-frequency = <33333333>;
};
core_clk: core-clk@80 {
compatible = "snps,axs10x-arc-pll-clock";
reg = <0x80 0x10>, <0x100 0x10>;
#clock-cells = <0>;
clocks = <&input_clk>;
/*
* Set initial core pll output frequency to 100MHz.
* It will be applied at the core pll driver probing
* on early boot.
*/
assigned-clocks = <&core_clk>;
assigned-clock-rates = <100000000>;
};
core_intc: archs-intc@cpu {
compatible = "snps,archs-intc";
interrupt-controller;
#interrupt-cells = <1>;
};
idu_intc: idu-interrupt-controller {
compatible = "snps,archs-idu-intc";
interrupt-controller;
interrupt-parent = <&core_intc>;
#interrupt-cells = <1>;
};
/*
* this GPIO block ORs all interrupts on CPU card (creg,..)
* to uplink only 1 IRQ to ARC core intc
*/
dw-apb-gpio@2000 {
compatible = "snps,dw-apb-gpio";
reg = < 0x2000 0x80 >;
#address-cells = <1>;
#size-cells = <0>;
ictl_intc: gpio-controller@0 {
compatible = "snps,dw-apb-gpio-port";
gpio-controller;
#gpio-cells = <2>;
snps,nr-gpios = <30>;
reg = <0>;
interrupt-controller;
#interrupt-cells = <2>;
interrupt-parent = <&idu_intc>;
interrupts = <1>;
};
};
debug_uart: dw-apb-uart@5000 {
compatible = "snps,dw-apb-uart";
reg = <0x5000 0x100>;
clock-frequency = <33333000>;
interrupt-parent = <&ictl_intc>;
interrupts = <2 4>;
baud = <115200>;
reg-shift = <2>;
reg-io-width = <4>;
};
arcpct0: pct {
compatible = "snps,archs-pct";
#interrupt-cells = <1>;
interrupt-parent = <&core_intc>;
interrupts = <20>;
};
};
/*
* Mark DMA peripherals connected via IOC port as dma-coherent. We do
* it via overlay because peripherals defined in axs10x_mb.dtsi are
* used for both AXS101 and AXS103 boards and only AXS103 has IOC (so
* only AXS103 board has HW-coherent DMA peripherals)
* We don't need to mark pgu@17000 as dma-coherent because it uses
* external DMA buffer located outside of IOC aperture.
*/
axs10x_mb {
ethernet@18000 {
dma-coherent;
};
usb@40000 {
dma-coherent;
};
usb@60000 {
dma-coherent;
};
mmc@15000 {
dma-coherent;
};
};
/*
* This INTC is actually connected to DW APB GPIO
* which acts as a wire between MB INTC and CPU INTC.
* GPIO INTC is configured in platform init code
* and here we mimic direct connection from MB INTC to
* CPU INTC, thus we set "interrupts = <0 1>" instead of
* "interrupts = <12>"
*
* This intc actually resides on MB, but we move it here to
* avoid duplicating the MB dtsi file given that IRQ from
* this intc to cpu intc are different for axs101 and axs103
*/
mb_intc: interrupt-controller@e0012000 {
#interrupt-cells = <1>;
compatible = "snps,dw-apb-ictl";
reg = < 0x0 0xe0012000 0x0 0x200 >;
interrupt-controller;
interrupt-parent = <&idu_intc>;
interrupts = <0>;
};
memory {
device_type = "memory";
/* CONFIG_LINUX_RAM_BASE needs to match low mem start */
reg = <0x0 0x80000000 0x0 0x20000000 /* 512 MiB low mem */
0x1 0xc0000000 0x0 0x40000000>; /* 1 GiB highmem */
};
reserved-memory {
#address-cells = <2>;
#size-cells = <2>;
ranges;
/*
* Move frame buffer out of IOC aperture (0x8z-0xaz).
*/
frame_buffer: frame_buffer@be000000 {
compatible = "shared-dma-pool";
reg = <0x0 0xbe000000 0x0 0x2000000>;
no-map;
};
};
};