125 lines
3.4 KiB
YAML
125 lines
3.4 KiB
YAML
# SPDX-License-Identifier: GPL-2.0
|
|
# Copyright (C) 2021 Sebastian Reichel
|
|
%YAML 1.2
|
|
---
|
|
$id: http://devicetree.org/schemas/power/supply/bq24257.yaml#
|
|
$schema: http://devicetree.org/meta-schemas/core.yaml#
|
|
|
|
title: Binding for bq24250, bq24251 and bq24257 Li-Ion Charger
|
|
|
|
maintainers:
|
|
- Sebastian Reichel <sre@kernel.org>
|
|
|
|
allOf:
|
|
- $ref: power-supply.yaml#
|
|
|
|
properties:
|
|
compatible:
|
|
enum:
|
|
- ti,bq24250
|
|
- ti,bq24251
|
|
- ti,bq24257
|
|
|
|
reg:
|
|
maxItems: 1
|
|
|
|
interrupts:
|
|
maxItems: 1
|
|
|
|
ti,battery-regulation-voltage:
|
|
$ref: /schemas/types.yaml#/definitions/uint32
|
|
description: maximum charging voltage in uV
|
|
|
|
ti,charge-current:
|
|
$ref: /schemas/types.yaml#/definitions/uint32
|
|
description: maximum charging current in uA
|
|
|
|
ti,termination-current:
|
|
$ref: /schemas/types.yaml#/definitions/uint32
|
|
description: |
|
|
charge will be terminated when current in constant-voltage phase
|
|
drops below this value (in uA)
|
|
|
|
pg-gpios:
|
|
description: |
|
|
GPIO used for connecting the bq2425x device PG (Power Good) pin.
|
|
This pin is not available on all devices however it should be used if
|
|
possible as this is the recommended way to obtain the charger's input PG
|
|
state. If this pin is not specified a software-based approach for PG
|
|
detection is used.
|
|
maxItems: 1
|
|
|
|
ti,current-limit:
|
|
$ref: /schemas/types.yaml#/definitions/uint32
|
|
description: |
|
|
The maximum current to be drawn from the charger's input (in uA).
|
|
If this property is not specified, the input limit current is set
|
|
automatically using USB D+/D- signal based charger type detection.
|
|
If the hardware does not support the D+/D- based detection, a default
|
|
of 500,000 is used (=500mA) instead.
|
|
|
|
ti,ovp-voltage:
|
|
$ref: /schemas/types.yaml#/definitions/uint32
|
|
description: |
|
|
Configures the over voltage protection voltage (in uV).
|
|
If not specified a default of 6,5000,000 (=6.5V) is used.
|
|
|
|
ti,in-dpm-voltage:
|
|
$ref: /schemas/types.yaml#/definitions/uint32
|
|
description: |
|
|
Configures the threshold input voltage for the dynamic power path management (in uV).
|
|
If not specified a default of 4,360,000 (=4.36V) is used.
|
|
|
|
required:
|
|
- compatible
|
|
- reg
|
|
- interrupts
|
|
- ti,battery-regulation-voltage
|
|
- ti,charge-current
|
|
- ti,termination-current
|
|
|
|
additionalProperties: false
|
|
|
|
examples:
|
|
- |
|
|
#include <dt-bindings/gpio/gpio.h>
|
|
#include <dt-bindings/interrupt-controller/irq.h>
|
|
i2c0 {
|
|
#address-cells = <1>;
|
|
#size-cells = <0>;
|
|
|
|
charger@6a {
|
|
compatible = "ti,bq24257";
|
|
reg = <0x6a>;
|
|
interrupt-parent = <&gpio1>;
|
|
interrupts = <16 IRQ_TYPE_EDGE_BOTH>;
|
|
|
|
pg-gpios = <&gpio1 28 GPIO_ACTIVE_HIGH>;
|
|
|
|
ti,battery-regulation-voltage = <4200000>;
|
|
ti,charge-current = <1000000>;
|
|
ti,termination-current = <50000>;
|
|
};
|
|
};
|
|
- |
|
|
#include <dt-bindings/gpio/gpio.h>
|
|
#include <dt-bindings/interrupt-controller/irq.h>
|
|
i2c0 {
|
|
#address-cells = <1>;
|
|
#size-cells = <0>;
|
|
|
|
charger@6a {
|
|
compatible = "ti,bq24250";
|
|
reg = <0x6a>;
|
|
interrupt-parent = <&gpio1>;
|
|
interrupts = <16 IRQ_TYPE_EDGE_BOTH>;
|
|
|
|
ti,battery-regulation-voltage = <4200000>;
|
|
ti,charge-current = <500000>;
|
|
ti,termination-current = <50000>;
|
|
ti,current-limit = <900000>;
|
|
ti,ovp-voltage = <9500000>;
|
|
ti,in-dpm-voltage = <4440000>;
|
|
};
|
|
};
|