commit 2a87f17775 upstream.
Provide pgctl/cgctl_mask module parameters for overriding power and
clock gating policies respectively. These help deal with rare firmware
loading failures on some configurations. There're no golden masks that
cover all known problems so leave the defaults as is.
While at it, update avs_hda_l1sen_enable()'s definition so it aligns
with its power/clock friends.
Signed-off-by: Cezary Rojewski <cezary.rojewski@intel.com>
Link: https://lore.kernel.org/r/20221027124702.1761002-9-cezary.rojewski@intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
commit d56829e9c1 upstream.
Introduce avs_suspend_standby() and avs_resume_standby() to support S0IX
streaming. The AudioDSP is not shutdown during such scenario and the PCI
device is armed for possible wake operation through an audio event.
As capability for a stream to be active during low power S0 is based off
of ->ignore_suspend, adjust the field's value according to platform
capabilities if needed.
Signed-off-by: Piotr Maziarz <piotrx.maziarz@linux.intel.com>
Signed-off-by: Cezary Rojewski <cezary.rojewski@intel.com>
Link: https://lore.kernel.org/r/20221027124702.1761002-8-cezary.rojewski@intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
commit 730cb320ec upstream.
Streaming in S0iX differs from SX scenarios. Store the number of
so-called low-power streams to be able to differentiate between the two.
Signed-off-by: Cezary Rojewski <cezary.rojewski@intel.com>
Link: https://lore.kernel.org/r/20221027124702.1761002-7-cezary.rojewski@intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
commit eb0699c4cd upstream.
Resuming of capture streams for HD-Audio is unsupported so remove the
relevant flag from the hardware params when assigning them during
avs_component_hda_open().
Signed-off-by: Cezary Rojewski <cezary.rojewski@intel.com>
Link: https://lore.kernel.org/r/20221027124702.1761002-6-cezary.rojewski@intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
commit 8e097f9a55 upstream.
With power management operations added, service SUSPEND and RESUME
trigger commands for running streams.
Signed-off-by: Amadeusz Sławiński <amadeuszx.slawinski@linux.intel.com>
Signed-off-by: Cezary Rojewski <cezary.rojewski@intel.com>
Link: https://lore.kernel.org/r/20221027124702.1761002-5-cezary.rojewski@intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
commit efffb01447 upstream.
Allow for waiting for DRSM bit for specified stream to be cleared from
HDAudio library level. Drivers may utilize this optional step during the
stream resume procedure.
Suggested-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Cezary Rojewski <cezary.rojewski@intel.com>
Reviewed-by: Takashi Iwai <tiwai@suse.de>
Link: https://lore.kernel.org/r/20221027124702.1761002-4-cezary.rojewski@intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
commit 2b9a50ea84 upstream.
Implement suspend/resume() operations for component drivers. For most
scenarios, the PM flow is similar to standard streaming one, except for
the part where the position register are being saved and the lack of PCM
pages freeing. To reduce code duplication, all avs_dai_suspend_XXX() and
avs_dai_resume_XXX() functions reuse their non-PM equivalents.
Given that path binding/unbinding happens only in FE part of the stream,
the order of suspend() goes:
1. hw_free() all FE DAIs, paths are unbound here
2. hw_free() all BE DAIs
Consequently, for resume() its:
1. hw_params() all BE DAIs
2. hw_params() all FE DAIs, paths are bound here
3. prepare() all BE DAIs
4. prepare() all FE DAIs
As component->suspend/resume() do not provide substream pointer, store
it ourselves so that the PM flow has all the necessary information to
proceed.
Signed-off-by: Cezary Rojewski <cezary.rojewski@intel.com>
Link: https://lore.kernel.org/r/20221027124702.1761002-3-cezary.rojewski@intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
commit 0abfc84ba2 upstream.
Prepare for introduction of PCM power management support. As freeing
pages during the suspend operation is not desired, separate
snd_pcm_lib_free_pages() from existing avs_dai_fe_hw_free() so that
majority of the code found within it can be reused for standard and PM
flows both.
Signed-off-by: Cezary Rojewski <cezary.rojewski@intel.com>
Link: https://lore.kernel.org/r/20221027124702.1761002-2-cezary.rojewski@intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
commit 6258234129 upstream.
The SPIB and DRMS capabilities are orthogonal to the DSP enablement
and can be used whether the stream is coupled or not.
The existing code partitioning makes limited sense, the capabilities
are parsed at the sound/hda level but helpers are located in
sound/hda/ext.
This patch moves all the SPIB/DRMS functionality to the sound/hda
layer. This reduces the complexity of the sound/hda/ext layer which is
now limited to handling the multi-link extensions and stream
coupling/decoupling helpers.
Note that this is an iso-functionality code move and rename, the
HDaudio legacy driver would need additional changes to make use of
these capabilities.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://lore.kernel.org/r/20221019162115.185917-11-pierre-louis.bossart@linux.intel.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
commit f90025100f upstream.
commit 0b00a5615d ("ALSA: hdac_ext: add hdac extended controller")
introduced a for() loop on the number of HDaudio codecs that seems
completely useless.
a) the body of the loop does not make use of the loop index, and
b) the LSDIID register is related to the SDI line, so there can only
be one codec per multi-link descriptor.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Link: https://lore.kernel.org/r/20221019162115.185917-10-pierre-louis.bossart@linux.intel.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
commit 26646c199b upstream.
My esteemed colleagues keep using the same words for different things.
The multi-link structure needs to be handled whether the DSP is
enabled or not.
The host and link DMAs are only relevant when the DSP is enabled.
Things get convoluted when there's an ambiguity between the LOSIDV
settings in the multi-link register space and the selection of the
stream_tag for the link DMA.
Clarify with a rename that the static functions used are related to
the host and link DMAs only.
No functionality change, pure rename.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com>
Link: https://lore.kernel.org/r/20221019162115.185917-9-pierre-louis.bossart@linux.intel.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
commit 7fa403f2a0 upstream.
All the helpers dealing with multi-link configurations are located in
the hdac_ext_controller.c, except the two set/clear routines that
modify the LOSIDV registers.
For consistency, move the two helpers and add the 'bus' prefix. One
could argue that the 'ml' prefix might be more relevant but that would
be a larger code change.
No functionality change, just move and rename.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com>
Link: https://lore.kernel.org/r/20221019162115.185917-8-pierre-louis.bossart@linux.intel.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
commit 00b6cd957d upstream.
We should only use 'link' in the context of multi-link
configurations. Streams are configured from a different register space
and are not dependent on link except for LOSIDV settings.
Not functionality change, just pure rename.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com>
Link: https://lore.kernel.org/r/20221019162115.185917-7-pierre-louis.bossart@linux.intel.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
commit 7f05ca9a74 upstream.
No functionality change, just prefix addition to clearly identify that
the helper only applies to the 'ext' part for Intel platforms.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com>
Link: https://lore.kernel.org/r/20221019162115.185917-6-pierre-louis.bossart@linux.intel.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
commit b0cd60f3e9 upstream.
We have two helpers with confusing names and different purposes.
Rename bus_get_link() and bus_get_link_at() as bus_get_hlink_by_name()
and bus_get_hlink_by_addr() respectively.
No functionality change
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Rander Wang <rander.wang@intel.com>
Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com>
Link: https://lore.kernel.org/r/20221019162115.185917-5-pierre-louis.bossart@linux.intel.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
commit 65edda6015 upstream.
ENABLE_LOGS and SYSTEM_TIME IPCs call LARGE_CONFIG_SET internally which
dumps an error message in case of an error. There is no need to repeat
the process in the top level handler.
Signed-off-by: Cezary Rojewski <cezary.rojewski@intel.com>
Link: https://lore.kernel.org/r/20221010121955.718168-13-cezary.rojewski@intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
commit 2d27a1caf8 upstream.
Utilize NOT_SUPPORTED status code to differentiate between unsupported
and invalid requests. Skip over error paths if it is the former that is
communicated by the base firmware.
Signed-off-by: Cezary Rojewski <cezary.rojewski@intel.com>
Link: https://lore.kernel.org/r/20221010121955.718168-12-cezary.rojewski@intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
commit 18a787909c upstream.
While LOG_BUFFER_STATUS is a simple notification with only one
meaningful field, same message ptr shall not be reused for two different
handlers.
Signed-off-by: Cezary Rojewski <cezary.rojewski@intel.com>
Link: https://lore.kernel.org/r/20221010121955.718168-11-cezary.rojewski@intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
commit e331b534d3 upstream.
In some configurations board fails to compile due to missing header. Add
it to fix build.
Signed-off-by: Amadeusz Sławiński <amadeuszx.slawinski@linux.intel.com>
Signed-off-by: Cezary Rojewski <cezary.rojewski@intel.com>
Link: https://lore.kernel.org/r/20221010121955.718168-10-cezary.rojewski@intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
commit fecc00b448 upstream.
KBL and APL devices use same codec but have different clock, so it must
be set appropriately depending on device.
Signed-off-by: Amadeusz Sławiński <amadeuszx.slawinski@linux.intel.com>
Signed-off-by: Cezary Rojewski <cezary.rojewski@intel.com>
Link: https://lore.kernel.org/r/20221010121955.718168-7-cezary.rojewski@intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
commit 999ce9967a upstream.
In order to load proper board configuration it needs to be looked up in
ACPI. Add board configuration for MAXIM 98927 codec present on
Chromebooks.
Reviewed-by: Cezary Rojewski <cezary.rojewski@intel.com>
Signed-off-by: Amadeusz Sławiński <amadeuszx.slawinski@linux.intel.com>
Link: https://lore.kernel.org/r/20220930124538.354992-3-amadeuszx.slawinski@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
-----BEGIN PGP SIGNATURE-----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=RyJn
-----END PGP SIGNATURE-----
Merge tag 'v6.1.80' into lts2022/linux
This is the 6.1.80 stable release
* tag 'v6.1.80': (470 commits)
Linux 6.1.80
fs/ntfs3: Enhance the attribute size check
arp: Prevent overflow in arp_req_get().
ahci: Extend ASM1061 43-bit DMA address quirk to other ASM106x parts
ata: ahci: add identifiers for ASM2116 series adapters
mptcp: add needs_id for netlink appending addr
mptcp: userspace pm send RM_ADDR for ID 0
mm: zswap: fix missing folio cleanup in writeback race path
fs/aio: Restrict kiocb_set_cancel_fn() to I/O submitted via libaio
mm/damon/reclaim: fix quota stauts loss due to online tunings
erofs: fix inconsistent per-file compression format
erofs: simplify compression configuration parser
i2c: imx: when being a target, mark the last read as processed
drm/amd/display: Fix memory leak in dm_sw_fini()
drm/syncobj: call drm_syncobj_fence_add_wait when WAIT_AVAILABLE flag is set
net: phy: realtek: Fix rtl8211f_config_init() for RTL8211F(D)(I)-VD-CG PHY
Fix write to cloned skb in ipv6_hop_ioam()
phonet/pep: fix racy skb_queue_empty() use
phonet: take correct lock to peek at the RX queue
net: sparx5: Add spinlock for frame transmission from CPU
...
If the connected panel supports both DRRS & PSR, driver gives preference
to PSR ("DRRS enabled: no"). Even though the hardware supports DRRS,
IGT treats ("DRRS enabled: yes") as not capable.
Introduce a new entry "DRRS capable" to debugfs i915_drrs_status, so
that IGT will read the DRRS capability as "DRRS capable: yes".
Signed-off-by: Bhanuprakash Modem <bhanuprakash.modem@intel.com>
Reviewed-by: Mitul Golani <mitulkumar.ajitkumar.golani@intel.com>
Signed-off-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240221111223.2313692-1-bhanuprakash.modem@intel.com
Fix "double" clearing of interrupts, which can cause external events
or timestamps to be missed.
The E1000_TSIRC Time Sync Interrupt Cause register can be cleared in two
ways, by either reading it or by writing '1' into the specific cause
bit. This is documented in section 8.16.1.
The following flow was used:
1. read E1000_TSIRC into 'tsicr';
2. handle the interrupts present into 'tsirc' and mark them in 'ack';
3. write 'ack' into E1000_TSICR;
As both (1) and (3) will clear the interrupt cause, if the same
interrupt happens again between (1) and (3) it will be ignored,
causing events to be missed.
Remove the extra clear in (3).
Fixes: 00c65578b4 ("igb: enable internal PPS for the i210")
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Fix "double" clearing of interrupts, which can cause external events
or timestamps to be missed.
The IGC_TSIRC Time Sync Interrupt Cause register can be cleared in two
ways, by either reading it or by writing '1' into the specific cause
bit. This is documented in section 8.16.1.
The following flow was used:
1. read IGC_TSIRC into 'tsicr';
2. handle the interrupts present in 'tsirc' and mark them in 'ack';
3. write 'ack' into IGC_TSICR;
As both (1) and (3) will clear the interrupt cause, if the same
interrupt happens again between (1) and (3) it will be ignored,
causing events to be missed.
Remove the extra clear in (3).
Fixes: 2c344ae245 ("igc: Add support for TX timestamping")
Reviewed-by: Kurt Kanzenbach <kurt@linutronix.de>
Tested-by: Kurt Kanzenbach <kurt@linutronix.de> # Intel i225
Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
commit 51af8f255bdaca6d501afc0d085b808f67b44d91 upstream.
ASMedia have confirmed that all ASM106x parts currently listed in
ahci_pci_tbl[] suffer from the 43-bit DMA address limitation that we ran
into on the ASM1061, and therefore, we need to apply the quirk added by
commit 20730e9b2778 ("ahci: add 43-bit DMA address quirk for ASMedia
ASM1061 controllers") to the other supported ASM106x parts as well.
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/linux-ide/ZbopwKZJAKQRA4Xv@x1-carbon/
Signed-off-by: Lennert Buytenhek <kernel@wantstofly.org>
[cassel: add link to ASMedia confirmation email]
Signed-off-by: Niklas Cassel <cassel@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3bf6141060948e27b62b13beb216887f2e54591e upstream.
Add support for PCIe SATA adapter cards based on Asmedia 2116 controllers.
These cards can provide up to 10 SATA ports on PCIe card.
Signed-off-by: Szuying Chen <Chloe_Chen@asmedia.com.tw>
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 584f3894262634596532cf43a5e782e34a0ce374 upstream.
Just the same as userspace PM, a new parameter needs_id is added for
in-kernel PM mptcp_pm_nl_append_new_local_addr() too.
Add a new helper mptcp_pm_has_addr_attr_id() to check whether an address
ID is set from PM or not.
In mptcp_pm_nl_get_local_id(), needs_id is always true, but in
mptcp_pm_nl_add_addr_doit(), pass mptcp_pm_has_addr_attr_id() to
needs_it.
Fixes: efd5a4c04e ("mptcp: add the address ID assignment bitmap")
Cc: stable@vger.kernel.org
Signed-off-by: Geliang Tang <tanggeliang@kylinos.cn>
Reviewed-by: Mat Martineau <martineau@kernel.org>
Signed-off-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 84c531f54ad9a124a924c9505d74e33d16965146 upstream.
This patch adds the ability to send RM_ADDR for local ID 0. Check
whether id 0 address is removed, if not, put id 0 into a removing
list, pass it to mptcp_pm_remove_addr() to remove id 0 address.
There is no reason not to allow the userspace to remove the initial
address (ID 0). This special case was not taken into account not
letting the userspace to delete all addresses as announced.
Closes: https://github.com/multipath-tcp/mptcp_net-next/issues/379
Reviewed-by: Matthieu Baerts <matttbe@kernel.org>
Signed-off-by: Geliang Tang <geliang.tang@suse.com>
Signed-off-by: Mat Martineau <martineau@kernel.org>
Link: https://lore.kernel.org/r/20231025-send-net-next-20231025-v1-3-db8f25f798eb@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Fixes: d9a4594eda ("mptcp: netlink: Add MPTCP_PM_CMD_REMOVE")
Signed-off-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e3b63e966cac0bf78aaa1efede1827a252815a1d upstream.
In zswap_writeback_entry(), after we get a folio from
__read_swap_cache_async(), we grab the tree lock again to check that the
swap entry was not invalidated and recycled. If it was, we delete the
folio we just added to the swap cache and exit.
However, __read_swap_cache_async() returns the folio locked when it is
newly allocated, which is always true for this path, and the folio is
ref'd. Make sure to unlock and put the folio before returning.
This was discovered by code inspection, probably because this path handles
a race condition that should not happen often, and the bug would not crash
the system, it will only strand the folio indefinitely.
Link: https://lkml.kernel.org/r/20240125085127.1327013-1-yosryahmed@google.com
Fixes: 04fc781608 ("mm: fix zswap writeback race condition")
Signed-off-by: Yosry Ahmed <yosryahmed@google.com>
Reviewed-by: Chengming Zhou <zhouchengming@bytedance.com>
Acked-by: Johannes Weiner <hannes@cmpxchg.org>
Reviewed-by: Nhat Pham <nphamcs@gmail.com>
Cc: Domenico Cerasuolo <cerasuolodomenico@gmail.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Yosry Ahmed <yosryahmed@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b820de741ae48ccf50dd95e297889c286ff4f760 upstream.
If kiocb_set_cancel_fn() is called for I/O submitted via io_uring, the
following kernel warning appears:
WARNING: CPU: 3 PID: 368 at fs/aio.c:598 kiocb_set_cancel_fn+0x9c/0xa8
Call trace:
kiocb_set_cancel_fn+0x9c/0xa8
ffs_epfile_read_iter+0x144/0x1d0
io_read+0x19c/0x498
io_issue_sqe+0x118/0x27c
io_submit_sqes+0x25c/0x5fc
__arm64_sys_io_uring_enter+0x104/0xab0
invoke_syscall+0x58/0x11c
el0_svc_common+0xb4/0xf4
do_el0_svc+0x2c/0xb0
el0_svc+0x2c/0xa4
el0t_64_sync_handler+0x68/0xb4
el0t_64_sync+0x1a4/0x1a8
Fix this by setting the IOCB_AIO_RW flag for read and write I/O that is
submitted by libaio.
Suggested-by: Jens Axboe <axboe@kernel.dk>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Avi Kivity <avi@scylladb.com>
Cc: Sandeep Dhavale <dhavale@google.com>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Kent Overstreet <kent.overstreet@linux.dev>
Cc: stable@vger.kernel.org
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Link: https://lore.kernel.org/r/20240215204739.2677806-2-bvanassche@acm.org
Signed-off-by: Christian Brauner <brauner@kernel.org>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1b0ca4e4ff10a2c8402e2cf70132c683e1c772e4 upstream.
Patch series "mm/damon: fix quota status loss due to online tunings".
DAMON_RECLAIM and DAMON_LRU_SORT is not preserving internal quota status
when applying new user parameters, and hence could cause temporal quota
accuracy degradation. Fix it by preserving the status.
This patch (of 2):
For online parameters change, DAMON_RECLAIM creates new scheme based on
latest values of the parameters and replaces the old scheme with the new
one. When creating it, the internal status of the quota of the old
scheme is not preserved. As a result, charging of the quota starts from
zero after the online tuning. The data that collected to estimate the
throughput of the scheme's action is also reset, and therefore the
estimation should start from the scratch again. Because the throughput
estimation is being used to convert the time quota to the effective size
quota, this could result in temporal time quota inaccuracy. It would be
recovered over time, though. In short, the quota accuracy could be
temporarily degraded after online parameters update.
Fix the problem by checking the case and copying the internal fields for
the status.
Link: https://lkml.kernel.org/r/20240216194025.9207-1-sj@kernel.org
Link: https://lkml.kernel.org/r/20240216194025.9207-2-sj@kernel.org
Fixes: e035c280f6 ("mm/damon/reclaim: support online inputs update")
Signed-off-by: SeongJae Park <sj@kernel.org>
Cc: <stable@vger.kernel.org> [5.19+]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 118a8cf504d7dfa519562d000f423ee3ca75d2c4 upstream.
EROFS can select compression algorithms on a per-file basis, and each
per-file compression algorithm needs to be marked in the on-disk
superblock for initialization.
However, syzkaller can generate inconsistent crafted images that use
an unsupported algorithmtype for specific inodes, e.g. use MicroLZMA
algorithmtype even it's not set in `sbi->available_compr_algs`. This
can lead to an unexpected "BUG: kernel NULL pointer dereference" if
the corresponding decompressor isn't built-in.
Fix this by checking against `sbi->available_compr_algs` for each
m_algorithmformat request. Incorrect !erofs_sb_has_compr_cfgs preset
bitmap is now fixed together since it was harmless previously.
Reported-by: <bugreport@ubisectech.com>
Fixes: 8f89926290 ("erofs: get compression algorithms directly on mapping")
Fixes: 622ceaddb7 ("erofs: lzma compression support")
Reviewed-by: Yue Hu <huyue2@coolpad.com>
Link: https://lore.kernel.org/r/20240113150602.1471050-1-hsiangkao@linux.alibaba.com
Signed-off-by: Gao Xiang <hsiangkao@linux.alibaba.com>
Signed-off-by: Gao Xiang <hsiangkao@linux.alibaba.com>
Signed-off-by: Yue Hu <huyue2@coolpad.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit efb4fb02cef3ab410b603c8f0e1c67f61d55f542 upstream.
Move erofs_load_compr_cfgs() into decompressor.c as well as introduce
a callback instead of a hard-coded switch for each algorithm for
simplicity.
Reviewed-by: Chao Yu <chao@kernel.org>
Signed-off-by: Gao Xiang <hsiangkao@linux.alibaba.com>
Link: https://lore.kernel.org/r/20231022130957.11398-1-xiang@kernel.org
Stable-dep-of: 118a8cf504d7 ("erofs: fix inconsistent per-file compression format")
Signed-off-by: Yue Hu <huyue2@coolpad.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 87aec499368d488c20292952d6d4be7cb9e49c5e ]
When being a target, NAK from the controller means that all bytes have
been transferred. So, the last byte needs also to be marked as
'processed'. Otherwise index registers of backends may not increase.
Fixes: f7414cd692 ("i2c: imx: support slave mode for imx I2C driver")
Signed-off-by: Corey Minyard <minyard@acm.org>
Tested-by: Andrew Manley <andrew.manley@sealingtech.com>
Reviewed-by: Andrew Manley <andrew.manley@sealingtech.com>
Reviewed-by: Oleksij Rempel <o.rempel@pengutronix.de>
[wsa: fixed comment and commit message to properly describe the case]
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3c43177ffb54ea5be97505eb8e2690e99ac96bc9 ]
When waiting for a syncobj timeline point whose fence has not yet been
submitted with the WAIT_FOR_SUBMIT flag, a callback is registered using
drm_syncobj_fence_add_wait and the thread is put to sleep until the
timeout expires. If the fence is submitted before then,
drm_syncobj_add_point will wake up the sleeping thread immediately which
will proceed to wait for the fence to be signaled.
However, if the WAIT_AVAILABLE flag is used instead,
drm_syncobj_fence_add_wait won't get called, meaning the waiting thread
will always sleep for the full timeout duration, even if the fence gets
submitted earlier. If it turns out that the fence *has* been submitted
by the time it eventually wakes up, it will still indicate to userspace
that the wait completed successfully (it won't return -ETIME), but it
will have taken much longer than it should have.
To fix this, we must call drm_syncobj_fence_add_wait if *either* the
WAIT_FOR_SUBMIT flag or the WAIT_AVAILABLE flag is set. The only
difference being that with WAIT_FOR_SUBMIT we will also wait for the
fence to be signaled after it has been submitted while with
WAIT_AVAILABLE we will return immediately.
IGT test patch: https://lists.freedesktop.org/archives/igt-dev/2024-January/067537.html
v1 -> v2: adjust lockdep_assert_none_held_once condition
(cherry picked from commit 8c44ea81634a4a337df70a32621a5f3791be23df)
Fixes: 01d6c35783 ("drm/syncobj: add support for timeline point wait v8")
Signed-off-by: Erik Kurzinger <ekurzinger@nvidia.com>
Signed-off-by: Simon Ser <contact@emersion.fr>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Simon Ser <contact@emersion.fr>
Link: https://patchwork.freedesktop.org/patch/msgid/20240119163208.3723457-1-ekurzinger@nvidia.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
Cezary Rojewski