Commit Graph

6 Commits

Author SHA1 Message Date
Haavard Skinnemoen c164b90135 [AVR32] Remove mii_phy_addr and eth_addr from eth_platform_data
The macb driver will probe for the PHY chip and read the mac address
from the MACB registers, so we don't need them in eth_platform_data
anymore.

Since u-boot doesn't currently initialize the MACB registers with the
mac addresses, the tag parsing code is kept but instead of sticking
the information into eth_platform_data, it uses it to initialize
the MACB registers (in case the boot loader didn't do it.) This code
should be unnecessary at some point in the future.

Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
2006-12-08 13:06:19 +01:00
Haavard Skinnemoen a6f92f3dc8 [AVR32] Move ethernet tag parsing to board-specific code
By moving the ethernet tag parsing to the board-specific code we avoid
the issue of figuring out which device we're supposed to attach the
information to.  The board specific code knows this because it's
where the actual devices are instantiated.

Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
2006-12-08 13:06:19 +01:00
Haavard Skinnemoen e9a43850e6 AVR32: Get rid of board_early_init
board_early_init() is left over from some early prototyping work
where we had to initialize the SDRAM controller ourselves. This
depends on the kernel being loaded into static RAM, which just
isn't possible on any commercially available products today.

In order to run without a boot loader, we need to create a zImage
stub or have the debugger initialize the SDRAM for us (for really
low-level debugging)

Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
2006-11-06 10:43:23 +01:00
Haavard Skinnemoen c194588dba [PATCH] AVR32: Allow renumbering of serial devices
Allow the board to remap actual USART peripheral devices to serial
devices by calling at32_map_usart(hw_id, serial_line). This ensures
that even though ATSTK1002 uses USART1 as the first serial port, it
will still have a ttyS0 device.

This also adds a board-specific early setup hook and moves the
at32_setup_serial_console() call there from the platform code.

Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-10-04 10:25:06 -07:00
Haavard Skinnemoen 2514183dff [PATCH] AVR32 MTD: AT49BV6416 platform device for ATSTK1000
FRegister a platform device for the AT49BV6416 NOR flash chip on the ATSTK1000
development board for use by the physmap MTD driver.

The SMC timings are set up before the platform device is registered so that no
board-specific mapping driver is necessary.

Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Cc: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-09-26 08:48:54 -07:00
Haavard Skinnemoen 5f97f7f940 [PATCH] avr32 architecture
This adds support for the Atmel AVR32 architecture as well as the AT32AP7000
CPU and the AT32STK1000 development board.

AVR32 is a new high-performance 32-bit RISC microprocessor core, designed for
cost-sensitive embedded applications, with particular emphasis on low power
consumption and high code density.  The AVR32 architecture is not binary
compatible with earlier 8-bit AVR architectures.

The AVR32 architecture, including the instruction set, is described by the
AVR32 Architecture Manual, available from

http://www.atmel.com/dyn/resources/prod_documents/doc32000.pdf

The Atmel AT32AP7000 is the first CPU implementing the AVR32 architecture.  It
features a 7-stage pipeline, 16KB instruction and data caches and a full
Memory Management Unit.  It also comes with a large set of integrated
peripherals, many of which are shared with the AT91 ARM-based controllers from
Atmel.

Full data sheet is available from

http://www.atmel.com/dyn/resources/prod_documents/doc32003.pdf

while the CPU core implementation including caches and MMU is documented by
the AVR32 AP Technical Reference, available from

http://www.atmel.com/dyn/resources/prod_documents/doc32001.pdf

Information about the AT32STK1000 development board can be found at

http://www.atmel.com/dyn/products/tools_card.asp?tool_id=3918

including a BSP CD image with an earlier version of this patch, development
tools (binaries and source/patches) and a root filesystem image suitable for
booting from SD card.

Alternatively, there's a preliminary "getting started" guide available at
http://avr32linux.org/twiki/bin/view/Main/GettingStarted which provides links
to the sources and patches you will need in order to set up a cross-compiling
environment for avr32-linux.

This patch, as well as the other patches included with the BSP and the
toolchain patches, is actively supported by Atmel Corporation.

[dmccr@us.ibm.com: Fix more pxx_page macro locations]
[bunk@stusta.de: fix `make defconfig']
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Dave McCracken <dmccr@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-09-26 08:48:54 -07:00