Modules: YMFPCI driver
Added rear_swap module option / kernel parameter to configure the rear
channel swapping. Default value is enable to make the AC3 passthrough
working, but analog only users might revert the previous behaviour.
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
Modules: YMFPCI driver
The routing of the effect 2/3 channels to the digital output is the
opposite of the rear analog output (left/right swapped).
We make the order correct for the digital output (which will make the
analog rear have the channels swapped) to make AC3 output work.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Modules: YMFPCI driver
Set the (read only) sample rate field in the IEC958 mixer controls to
48 kHz (instead of 44.1 kHz) because that is the rate actually
supported by the hardware.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Modules: YMFPCI driver
Instead of 'DS-XG', show the correct chip model (DS-1/1L/1S/1E) where possible.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Use schedule_timeout_{,un}interruptible() instead of
set_current_state()/schedule_timeout() to reduce kernel size. Also use
human-time conversion functions instead of hard-coded division to avoid
rounding issues.
Signed-off-by: Nishanth Aravamudan <nacc@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Modules: YMFPCI driver
We better pretend that the ymfpci timer runs at 48 kHz because the
interrupt frequency cannot be higher, and clients that would try to
use 96 kHz would run at half their desired speed.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
- Remove vmalloc wrapper
- Add release_and_free_resource() to remove kfree_nocheck() from each driver
and simplify the code
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Modules: YMFPCI driver
This patch adds a new mixer control called 'IEC958 Loop' which makes
it possible to loop digital signals from S/PDIF-in to S/PDIF-out.
Signed-off-by: Glen Masgai <mimosius@gmx.de>
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
YMFPCI driver
Implements mixer controls for the volume of each playback substream of
the main PCM device.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
ENS1370/1+ driver,ES1968 driver,Intel8x0 driver,VIA82xx driver
VIA82xx-modem driver,AC97 Codec,ALI5451 driver,CS46xx driver
MIXART driver,RME HDSP driver,Trident driver,YMFPCI driver
Description: Fix-up sleeping in sound/pci. These changes fall under the
following two categories:
1) Replace schedule_timeout() with msleep() to guarantee the
task delays as expected. This also involved replacing/removing
custom sleep functions.
2) Do not assume jiffies will only increment by one if you
request a 1 jiffy sleep, i.e. use time_after/time_before in
while loops.
Signed-off-by: Nishanth Aravamudan <nacc@us.ibm.com>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
Timer Midlevel,ALSA sequencer,ALSA<-OSS sequencer,Digigram VX core
I2C tea6330t,GUS Library,VIA82xx driver,VIA82xx-modem driver
CA0106 driver,CS46xx driver,EMU10K1/EMU10K2 driver,YMFPCI driver
Digigram VX Pocket driver,Common EMU synth,USB generic driver,USB USX2Y
Checking a pointer for NULL before calling kfree() on it is redundant,
kfree() deals with NULL pointers just fine.
This patch removes such checks from sound/
This patch also makes another, but closely related, change.
It avoids casting pointers about to be kfree()'ed.
Signed-off-by: Jesper Juhl <juhl-lkml@dif.dk>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
YMFPCI driver
This patch removes some dead code found by the Coverity checker.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Initial git repository build. I'm not bothering with the full history,
even though we have it. We can create a separate "historical" git
archive of that later if we want to, and in the meantime it's about
3.2GB when imported into git - space that would just make the early
git days unnecessarily complicated, when we don't have a lot of good
infrastructure for it.
Let it rip!
Jaroslav Kysela