Idle code is very like entry code in that RCU isn't available. As
such, add a little validation.
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Tested-by: Tony Lindgren <tony@atomide.com>
Tested-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Frederic Weisbecker <frederic@kernel.org>
Link: https://lore.kernel.org/r/20230112195540.373461409@infradead.org
The kernel start up code for all of the nommu m68k types expects the BSS
section to be on a 4-byte boundary, and to be a whole number of 32bit
words. The BSS initialization loop sets 32bit sized quantities and has
no provision for odd or unaligned accesses.
The alignment and size of the BSS has historically worked out to be 4-byte
aligned and sized - although no explicit alignment or size was specified in
the linker script. So the BSS zeroing code worked as expected.
A problem was first observed after commit 7273ad2b08 ("kbuild: link lib-y
objects to vmlinux forcibly when CONFIG_MODULES=y"). Some kernel builds,
depending on exact configuration, then tended to generate even sized BSS
sections - which is valid on m68k - but our BSS init code could not handle
properly.
The simplest and smallest solution is to align and size the BSS
appropriately.
Signed-off-by: Greg Ungerer <gerg@linux-m68k.org>
Commit c604abc3f6 ("vmlinux.lds.h: Split ELF_DETAILS from STABS_DEBUG")
after should add a missing ELF_DETAILS, at the same time, the .comment
section has been included in the ELF_DETAILS.
Signed-off-by: Youling Tang <tangyouling@loongson.cn>
Link: https://lore.kernel.org/r/1605852494-23515-1-git-send-email-tangyouling@loongson.cn
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Commit be7635e728 ("arch, ftrace: for KASAN put hard/soft IRQ entries
into separate sections") added a new linker section, SOFTIRQENTRY_TEXT,
to the linker scripts for most architectures. It didn't add it to any of
the linker scripts for the m68k architecture. This was not really a problem
because it is only defined if either of CONFIG_FUNCTION_GRAPH_TRACER or
CONFIG_KASAN are enabled - which can never be true for m68k.
However commit 229a718605 ("irq: Make the irqentry text section
unconditional") means that SOFTIRQENTRY_TEXT is now always defined. So on
m68k we now end up with a separate ELF section for .softirqentry.text
instead of it being part of the .text section. On some m68k targets in some
configurations this can also cause a fatal link error:
LD vmlinux
/usr/local/bin/../m68k-uclinux/bin/ld.real: section .softirqentry.text loaded at [0000000010de10c0,0000000010de12dd] overlaps section .rodata loaded at [0000000010de10c0,0000000010e0fd67]
To fix add in the missing SOFTIRQENTRY_TEXT section into the m68k linker
scripts. I noticed that m68k is also missing the IRQENTRY_TEXT section,
so this patch also adds an entry for that too.
Signed-off-by: Greg Ungerer <gerg@linux-m68k.org>
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When doing an nmi backtrace of many cores, most of which are idle, the
output is a little overwhelming and very uninformative. Suppress
messages for cpus that are idling when they are interrupted and just
emit one line, "NMI backtrace for N skipped: idling at pc 0xNNN".
We do this by grouping all the cpuidle code together into a new
.cpuidle.text section, and then checking the address of the interrupted
PC to see if it lies within that section.
This commit suitably tags x86 and tile idle routines, and only adds in
the minimal framework for other architectures.
Link: http://lkml.kernel.org/r/1472487169-14923-5-git-send-email-cmetcalf@mellanox.com
Signed-off-by: Chris Metcalf <cmetcalf@mellanox.com>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Tested-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Tested-by: Daniel Thompson <daniel.thompson@linaro.org> [arm]
Tested-by: Petr Mladek <pmladek@suse.com>
Cc: Aaron Tomlin <atomlin@redhat.com>
Cc: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: "Rafael J. Wysocki" <rjw@rjwysocki.net>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
BSS_SECTION() provides the __bss_{start,stop} symbols, so there's no need
to wrap our own _[se]bss around it.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Greg Ungerer<gerg@uclinux.org>
There is a lot of years of collected cruft in the m68knommu linker script.
Clean it all up and use the well defined linker script support macros.
Support is maintained for building both ROM/FLASH based and RAM based setups.
No major changes to section layouts, though the rodata section is now lumped
in with the read/write data section.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Use the non-MMU linker script for ColdFire builds when we are building
for MMU enabled. The image layout is correct for loading on existing
ColdFire dev boards. The only addition required to the current non-MMU
linker script is to add support for the fixup section.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Matt Waddel <mwaddel@yahoo.com>
Acked-by: Kurt Mahan <kmahan@xmission.com>
The merge of m68knommu left the linker scripts a little disorganized.
Some consistent naming and squashing two of scripts that just include
others can simplify things a lot.
So merge the two simple including scripts, and rename the nommu script
to be consistent with the existing m68k linker scripts.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Peter Zijlstra