In case of error, the function dev_get_regmap() returns NULL
pointer not ERR_PTR(). The IS_ERR() test in the return value
check should be replaced with NULL test.
Fixes: 9351ab8b0c ("regulator: rt4831: Adds support for Richtek RT4831 DSV regulator")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Link: https://lore.kernel.org/r/20210305034930.3236099-1-weiyongjun1@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The driver uses the DVS registers PCA9450_REG_BUCKxOUT_DVS0 to set the
voltage for the buck regulators 1, 2 and 3. This has no effect as the
PRESET_EN bit is set by default and therefore the preset values are used
instead, which are set to 850 mV.
To fix this we clear the PRESET_EN bit at time of initialization.
Fixes: 0935ff5f1f ("regulator: pca9450: add pca9450 pmic driver")
Cc: <stable@vger.kernel.org>
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Link: https://lore.kernel.org/r/20210222115229.166620-1-frieder.schrempf@kontron.de
Signed-off-by: Mark Brown <broonie@kernel.org>
This fixes the return value of pca9450_i2c_probe() to use the correct
error code when getting the sd-vsel GPIO fails.
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Link: https://lore.kernel.org/r/20210222150809.208942-1-frieder.schrempf@kontron.de
Signed-off-by: Mark Brown <broonie@kernel.org>
- Standardise MFD_CELL_* helpers
- New Drivers
- Add support for Acer Iconia Tab A500 Embedded Controller
- New Device Support
- Add support for ROHM BD9574MWF to BD9571MWV
- Add support for Intel Alder Lake PCH-P PCI to LPSS
- Add support for Intel Alder Lake PCH-S PCI to LPSS
- New Functionality
- Support ACPI enumeration; arizona
- Fix-ups
- Managed resources; bd9571mwv
- DT additions/fix-ups; bd9571mwv, iqs62x, max8997, gateworks-gsc, ene-kb930
- Convert to SPDX; bd9571mw
- Fix return values/error handling; sunxi
- Provide SOFTDEP; arizona
- Make use of DIV_ROUND_UP; mcp-sa11x0
- Use generic APIs; arizona
- Add MAC address sysfs entries; intel-m10-bmc
- Trivial: Coding-style fix-ups; iqs62x
- Trivial: Remove superflouous code; iqs62x
- Clear-up naming conventions; iqs62x
- Bug Fixes
- Fix 'pointer from integer' error; altera-sysmgr
- Convert SGI_MFD_IOC3 from tristate to bool; Kconfig
- Fix interrupt handling; gateworks-gsc
- Extend required delay; iqs62x
- Do not use I2C polling during calibration; iqs62x
- Do no adjust clock frequency during calibration; iqs62x
- Fix use-after-free; wm831x-auxad
-----BEGIN PGP SIGNATURE-----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=ieAS
-----END PGP SIGNATURE-----
Merge tag 'mfd-next-5.12' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd
Pull MFD updates from Lee Jones:
"Core Frameworks:
- Standardise MFD_CELL_* helpers
New Drivers:
- Add support for Acer Iconia Tab A500 Embedded Controller
New Device Support:
- Add support for ROHM BD9574MWF to BD9571MWV
- Add support for Intel Alder Lake PCH-P PCI to LPSS
- Add support for Intel Alder Lake PCH-S PCI to LPSS
New Functionality:
- Support ACPI enumeration; arizona
Fix-ups:
- Managed resources; bd9571mwv
- DT additions/fix-ups; bd9571mwv, iqs62x, max8997, gateworks-gsc, ene-kb930
- Convert to SPDX; bd9571mw
- Fix return values/error handling; sunxi
- Provide SOFTDEP; arizona
- Make use of DIV_ROUND_UP; mcp-sa11x0
- Use generic APIs; arizona
- Add MAC address sysfs entries; intel-m10-bmc
- Trivial: Coding-style fix-ups; iqs62x
- Trivial: Remove superflouous code; iqs62x
- Clear-up naming conventions; iqs62x
Bug Fixes:
- Fix 'pointer from integer' error; altera-sysmgr
- Convert SGI_MFD_IOC3 from tristate to bool; Kconfig
- Fix interrupt handling; gateworks-gsc
- Extend required delay; iqs62x
- Do not use I2C polling during calibration; iqs62x
- Do no adjust clock frequency during calibration; iqs62x
- Fix use-after-free; wm831x-auxad"
* tag 'mfd-next-5.12' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd: (32 commits)
mfd: wm831x-auxadc: Prevent use after free in wm831x_auxadc_read_irq()
mfd: iqs62x: Do not change clock frequency during ATI
mfd: iqs62x: Do not poll during ATI
mfd: iqs62x: Increase interrupt handler return delay
mfd: iqs62x: Rename regmap_config struct
mfd: iqs62x: Remove unused bit mask
mfd: iqs62x: Remove superfluous whitespace above fallthroughs
mfd: intel-lpss: Add Intel Alder Lake PCH-S PCI IDs
mfd: intel-m10-bmc: Expose MAC address and count
mfd: Add driver for Embedded Controller found on Acer Iconia Tab A500
dt-bindings: mfd: Add ENE KB930 Embedded Controller binding
dt-bindings: mfd: gateworks-gsc: Add fan-tach mode
mfd: intel-lpss: Add Intel Alder Lake PCH-P PCI IDs
mfd: gateworks-gsc: Fix interrupt type
mfd: Standardise MFD_CELL_* helper names
mfd: mcp-sa11x0: Use DIV_ROUND_UP to calculate rw_timeout
mfd: max8997: Add of_compatible to Extcon and Charger mfd_cell
dt-bindings: mfd: Correct the node name of the panel LED
mfd: sgi-ioc3: Turn Kconfig option into a bool
mfd: altera-sysmgr: Fix physical address storing more
...
The ROHM BD718x7 and BD71828 drivers support setting HW state
specific voltages from device-tree. This is used also by various
in-tree DTS files.
These drivers do incorrectly try to compose bit-map using enum
values. By a chance this works for first two valid levels having
values 1 and 2 - but setting values for the rest of the levels
do indicate capability of setting values for first levels as
well. Luckily the regulators which support setting values for
SUSPEND/LPSR do usually also support setting values for RUN
and IDLE too - thus this has not been such a fatal issue.
Fix this by defining the old enum values as bits and fixing the
parsing code. This allows keeping existing IC specific drivers
intact and only slightly changing the rohm-regulator.c
Fixes: 21b72156ed ("regulator: bd718x7: Split driver to common and bd718x7 specific parts")
Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20210212080023.GA880728@localhost.localdomain
Signed-off-by: Mark Brown <broonie@kernel.org>
By default the PCA9450 doesn't handle the assertion of the WDOG_B
signal, but this is required to guarantee that things like software
resets triggered by the watchdog work reliably.
As we don't want to rely on the bootloader to enable this, we tell
the PMIC to issue a cold reset in case the WDOG_B signal is
asserted (WDOG_B_CFG = 10), just as the NXP U-Boot code does.
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Link: https://lore.kernel.org/r/20210211105534.38972-3-frieder.schrempf@kontron.de
Signed-off-by: Mark Brown <broonie@kernel.org>
LDO5 has two separate control registers. LDO5CTRL_L is used if the
input signal SD_VSEL is low and LDO5CTRL_H if it is high.
The current driver implementation only uses LDO5CTRL_H. To make this
work on boards that have SD_VSEL connected to a GPIO, we add support
for specifying an optional GPIO and setting it to high at probe time.
In the future we might also want to add support for boards that have
SD_VSEL set to a fixed low level. In this case we need to change the
driver to be able to use the LDO5CTRL_L register.
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Link: https://lore.kernel.org/r/20210211105534.38972-1-frieder.schrempf@kontron.de
Signed-off-by: Mark Brown <broonie@kernel.org>
Use the correct name to avoid ldo7 commands being sent to ldo6's address.
Fixes: 06369bcc15 ("regulator: qcom-rpmh: Add support for SM8150")
Signed-off-by: Jonathan Marek <jonathan@marek.ca>
Reviewed-by: Vinod Koul <vkoul@kernel.org>
Link: https://lore.kernel.org/r/20210211034935.5622-1-jonathan@marek.ca
Signed-off-by: Mark Brown <broonie@kernel.org>
Calling the disable_irq() from irq handler might be a bad idea as
disable_irq() should wait for handlers to run. I don't see why
this wouldn't deadlock in wait_event waiting for the threaded
handler to complete.
Use disable_irq_nosync() instead.
Fixes: 390af53e04 ("regulator: qcom-labibb: Implement short-circuit and over-current IRQs")
Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@somainline.org>
Link: https://lore.kernel.org/r/f2c4c88d90bf7473e1b84b8a99b7b33d7a081764.1612249657.git.matti.vaittinen@fi.rohmeurope.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Sometimes regulator_get() gets called twice for the same supply on the
same device. This may happen e.g. when a framework / library is used
which uses the regulator; and the driver itself also needs to enable
the regulator in some cases where the framework will not enable it.
Commit ff268b56ce ("regulator: core: Don't spew backtraces on
duplicate sysfs") already takes care of the backtrace which would
trigger when creating a duplicate consumer symlink under
/sys/class/regulator/regulator.%d in this scenario.
Commit c33d442328 ("debugfs: make error message a bit more verbose")
causes a new error to get logged in this scenario:
[ 26.938425] debugfs: Directory 'wm5102-codec-MICVDD' with parent 'spi-WM510204:00-MICVDD' already present!
There is no _nowarn variant of debugfs_create_dir(), but we can detect
and avoid this problem by checking the return value of the earlier
sysfs_create_link_nowarn() call.
Add a check for the earlier sysfs_create_link_nowarn() failing with
-EEXIST and skip the debugfs_create_dir() call in that case, avoiding
this error getting logged.
Fixes: c33d442328 ("debugfs: make error message a bit more verbose")
Cc: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20210122183250.370571-1-hdegoede@redhat.com
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch adds suspend/resume support so that it is possible to
configure the LDOs and BUCKs as on or off during suspend phase as
well as to configure suspend specific voltages.
Signed-off-by: Christoph Fritz <chf.fritz@googlemail.com>
Link: https://lore.kernel.org/r/4c2e79d4fa96befdc9a6c59c3ff27b0a34f9fb56.camel@googlemail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Make regulator_sync_voltage() to re-balance voltage state of a coupled
regulators instead of changing the voltage directly.
Tested-by: Peter Geis <pgwipeout@gmail.com> # Ouya T30
Tested-by: Dmitry Osipenko <digetx@gmail.com> # A500 T20 and Nexus7 T30
Tested-by: Nicolas Chauvet <kwizart@gmail.com> # PAZ00 T20
Tested-by: Matt Merhar <mattmerhar@protonmail.com> # Ouya T30
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Link: https://lore.kernel.org/r/20210122174311.28230-1-digetx@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
With commit eaa7995c52 (regulator: core: avoid
regulator_resolve_supply() race condition) we started holding the rdev
lock while resolving supplies, an operation that requires holding the
regulator_list_mutex. This results in lockdep warnings since in other
places we take the list mutex then the mutex on an individual rdev.
Since the goal is to make sure that we don't call set_supply() twice
rather than a concern about the cost of resolution pull the rdev lock
and check for duplicate resolution down to immediately before we do the
set_supply() and drop it again once the allocation is done.
Fixes: eaa7995c52 (regulator: core: avoid regulator_resolve_supply() race condition)
Reported-by: Marek Szyprowski <m.szyprowski@samsung.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20210122132042.10306-1-broonie@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
The device node reference obtained with of_get_child_by_name() should be
dropped on error paths.
Fixes: 26aec009f6 ("regulator: add device tree support for s5m8767")
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20210121155914.48034-1-krzk@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
The regulators from PMC8180 and PMC8180C exposed by the RPMH in the
Qualcomm SC8180X seems to be the same as PM8150 and PM8150L. Add
compatibles for the two new PMICs and reuse the definition of the
existing PMICs.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20210120224901.1611232-2-bjorn.andersson@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Call of_node_put() to drop references of regulators_np and reg_np before
returning error code.
Fixes: 9ae5cc75ce ("regulator: s5m8767: Pass descriptor instead of GPIO number")
Signed-off-by: Pan Bian <bianpan2016@163.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20210121032756.49501-1-bianpan2016@163.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The ST-Ericsson U300 platform is getting removed, so this driver is no
longer needed.
Cc: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20210120151307.1726876-1-arnd@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Okay, the title may be a little "aggressive"? However, the qcom-labibb
driver wasn't really .. doing much.
The current form of this driver is only taking care of enabling or
disabling the regulators, which is pretty useless if they were not
pre-set from the bootloader, which sets them only if continuous
splash is enabled.
Moreover, some bootloaders are setting a higher voltage and/or a higher
current limit compared to what's actually required by the attached
hardware (which is, in 99.9% of the cases, a display) and this produces
a higher power consumption, higher heat output and a risk of actually
burning the display if kept up for a very long time: for example, this
is true on at least some Sony Xperia MSM8998 (Yoshino platform) and
especially on some Sony Xperia SDM845 (Tama platform) smartphones.
In any case, the main reason why this change was necessary for us is
that, during the bringup of Sony Xperia MSM8998 phones, we had an issue
with the bootloader not turning on the display and not setting the lab
and ibb regulators before booting the kernel, making it impossible to
powerup the display.
With this said, this patchset enables setting voltage, current limiting,
overcurrent and short-circuit protection.. and others, on the LAB/IBB
regulators.
Each commit in this patch series provides as many informations as
possible about what's going on and testing methodology.
Changes in v4:
- Remove already applied commit
- Add commit to switch to regulator_{list,map}_voltage_linear
which in v3 got squashed in the commit that got removed in v4.
Changes in v3:
- Improved check for PBS disable and short-circuit condition:
during the testing of short-circuit, coincidentally another
register reading zero on the interesting bit was probed,
which didn't trigger a malfunction of the SC logic, but was
also wrong.
After the change, the short-circuit test was re-done in the
same way as described in the commit that is implementing it.
- From Bjorn Andersson review:
- Improved documentation about over-current and short-circuit
protection in the driver
- Improved maintainability of qcom_labibb_sc_recovery_worker()
- Flipped around check for PBS vreg disabled in for loop of
function labibb_sc_err_handler()
- From Mark Brown (forgotten in v2):
- Changed regulator_{list,map}_voltage_linear_range usages to
regulator_{list,map}_voltage_linear (and fixed regulator
descs to reflect the change).
Changes in v2:
- From Mark Brown review:
- Replaced some if branches with switch statements
- Moved irq get and request in probe function
- Changed short conditionals to full ones
- Removed useless check for ocp_irq_requested
- Fixed issues with YAML documentation
AngeloGioacchino Del Regno (7):
regulator: qcom-labibb: Switch voltage ops from linear_range to linear
regulator: qcom-labibb: Implement current limiting
regulator: qcom-labibb: Implement pull-down, softstart, active
discharge
dt-bindings: regulator: qcom-labibb: Document soft start properties
regulator: qcom-labibb: Implement short-circuit and over-current IRQs
dt-bindings: regulator: qcom-labibb: Document SCP/OCP interrupts
arm64: dts: pmi8998: Add the right interrupts for LAB/IBB SCP and OCP
.../regulator/qcom-labibb-regulator.yaml | 30 +-
arch/arm64/boot/dts/qcom/pmi8998.dtsi | 8 +-
drivers/regulator/qcom-labibb-regulator.c | 720 +++++++++++++++++-
3 files changed, 735 insertions(+), 23 deletions(-)
--
2.30.0
Short-Circuit Protection (SCP) and Over-Current Protection (OCP) are
very important for regulators like LAB and IBB, which are designed to
provide from very small to relatively big amounts of current to the
device (normally, a display).
Now that this regulator supports both voltage setting and current
limiting in this driver, to me it looked like being somehow essential
to provide support for SCP and OCP, for two reasons:
1. SCP is a drastic measure to prevent damaging "more" hardware in
the worst situations, if any was damaged, preventing potentially
drastic issues;
2. OCP is a great way to protect the hardware that we're powering
through these regulators as if anything bad happens, the HW will
draw more current than expected: in this case, the OCP interrupt
will fire and the regulators will be immediately shut down,
preventing hardware damage in many cases.
Both interrupts were successfully tested in a "sort-of" controlled
manner, with the following methodology:
Short-Circuit Protection (SCP):
1. Set LAB/IBB to 4.6/-1.4V, current limit 200mA/50mA;
2. Connect a 10 KOhm resistor to LAB/IBB by poking the right traces
on a FxTec Pro1 smartphone for a very brief time (in short words,
"just a rapid touch with flying wires");
3. The Short-Circuit protection trips: IRQ raises, regulators get
cut. Recovery OK, test repeated without rebooting, OK.
Over-Current Protection (OCP):
1. Set LAB/IBB to the expected voltage to power up the display of
a Sony Xperia XZ Premium smartphone (Sharp LS055D1SX04), set
current limit to LAB 200mA, IBB 50mA (the values that this
display unit needs are 200/800mA);
2. Boot the kernel: OCP fires. Recovery never happens because
the selected current limit is too low, but that's expected.
Test OK.
3. Set LAB/IBB to the expected current limits for XZ Premium
(LAB 200mA, IBB 800mA), but lower than expected voltage,
specifically LAB 5.4V, IBB -5.6V (instead of 5.6, -5.8V);
4. Boot the kernel: OCP fires. Recovery never happens because
the selected voltage (still in the working range limits)
is producing a current draw of more than 200mA on LAB.
Test OK.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@somainline.org>
Link: https://lore.kernel.org/r/20210119174421.226541-6-angelogioacchino.delregno@somainline.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Soft start is required to avoid inrush current during LAB ramp-up and
IBB ramp-down, protecting connected hardware to which we supply voltage.
Since soft start is configurable on both LAB and IBB regulators, it
was necessary to add two DT properties, respectively "qcom,soft-start-us"
to control LAB ramp-up and "qcom,discharge-resistor-kohms" to control
the discharge resistor for IBB ramp-down, which obviously brought the
need of implementing a of_parse callback for both regulators.
Finally, also implement pull-down mode in order to avoid unpredictable
behavior when the regulators are disabled (random voltage spikes etc).
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@somainline.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20210119174421.226541-4-angelogioacchino.delregno@somainline.org
Signed-off-by: Mark Brown <broonie@kernel.org>
LAB and IBB regulators can be current-limited by setting the
appropriate registers, but this operation is granted only after
sending an unlock code for secure access.
Besides the secure access, it would be possible to use the
regmap helper for get_current_limit, as there is no security
blocking reads, but I chose not to as to avoid having a very
big array containing current limits, especially for IBB.
That said, these regulators support current limiting for:
- LAB (pos): 200-1600mA, with 200mA per step (8 steps),
- IBB (neg): 0-1550mA, with 50mA per step (32 steps).
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@somainline.org>
Link: https://lore.kernel.org/r/20210119174421.226541-3-angelogioacchino.delregno@somainline.org
Signed-off-by: Mark Brown <broonie@kernel.org>
The LAB and IBB regulator have just one range and it is useless
to use linear_range ops, as these are used to express multiple
linear ranges.
Switch list_voltage and map_voltage callbacks to *_linear instead.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@somainline.org>
Link: https://lore.kernel.org/r/20210119174421.226541-2-angelogioacchino.delregno@somainline.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Okay, the title may be a little "aggressive"? However, the qcom-labibb
driver wasn't really .. doing much.
The current form of this driver is only taking care of enabling or
disabling the regulators, which is pretty useless if they were not
pre-set from the bootloader, which sets them only if continuous
splash is enabled.
Moreover, some bootloaders are setting a higher voltage and/or a higher
current limit compared to what's actually required by the attached
hardware (which is, in 99.9% of the cases, a display) and this produces
a higher power consumption, higher heat output and a risk of actually
burning the display if kept up for a very long time: for example, this
is true on at least some Sony Xperia MSM8998 (Yoshino platform) and
especially on some Sony Xperia SDM845 (Tama platform) smartphones.
In any case, the main reason why this change was necessary for us is
that, during the bringup of Sony Xperia MSM8998 phones, we had an issue
with the bootloader not turning on the display and not setting the lab
and ibb regulators before booting the kernel, making it impossible to
powerup the display.
With this said, this patchset enables setting voltage, current limiting,
overcurrent and short-circuit protection.. and others, on the LAB/IBB
regulators.
Each commit in this patch series provides as many informations as
possible about what's going on and testing methodology.
Changes in v2:
- From Mark Brown review:
- Replaced some if branches with switch statements
- Moved irq get and request in probe function
- Changed short conditionals to full ones
- Removed useless check for ocp_irq_requested
- Fixed issues with YAML documentation
AngeloGioacchino Del Regno (7):
regulator: qcom-labibb: Implement voltage selector ops
regulator: qcom-labibb: Implement current limiting
regulator: qcom-labibb: Implement pull-down, softstart, active
discharge
dt-bindings: regulator: qcom-labibb: Document soft start properties
regulator: qcom-labibb: Implement short-circuit and over-current IRQs
dt-bindings: regulator: qcom-labibb: Document SCP/OCP interrupts
arm64: dts: pmi8998: Add the right interrupts for LAB/IBB SCP and OCP
.../regulator/qcom-labibb-regulator.yaml | 30 +-
arch/arm64/boot/dts/qcom/pmi8998.dtsi | 8 +-
drivers/regulator/qcom-labibb-regulator.c | 661 +++++++++++++++++-
3 files changed, 686 insertions(+), 13 deletions(-)
--
2.29.2
Implement {get,set}_voltage_sel, list_voltage, map_voltage with
the useful regulator regmap helpers in order to be able to manage
the voltage of LAB (positive) and IBB (negative) regulators.
In particular, the supported ranges are the following:
- LAB (pos): 4600mV to 6100mV with 100mV stepping,
- IBB (neg): -7700mV to -1400mV with 100mV stepping.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@somainline.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20210113194214.522238-2-angelogioacchino.delregno@somainline.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Fix the ternary condition which is a bad coding style
in the kernel
I also remove the defering configuration of the nxp,phase-shift.
The configuration is now done at parsing time. It save some memory
and it's better for comprehension.
I also use the OTP default configuration when the parameter is wrong
or not specified.
I think that it's better to use the default configuration from the chip
than an arbitrary value.
Signed-off-by: Adrien Grassein <adrien.grassein@gmail.com>
Link: https://lore.kernel.org/r/20210114174714.122561-7-adrien.grassein@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
This property seems useless because we can use the
regulator-max-microamp generic property to do the same
and using generic code.
As this property was already released in a kernel version,
we can't remove it, just mark it as deprecated.
Signed-off-by: Adrien Grassein <adrien.grassein@gmail.com>
Link: https://lore.kernel.org/r/20210114174714.122561-5-adrien.grassein@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Add support for BD9574MWF which is similar chip with BD9571MWV.
Note that we don't support voltage rails VD{09,18,25,33} by this
driver on BD9574. The VD09 voltage could be read from PMIC but that
is not supported by this commit.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Acked-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
To simplify this driver, use dev_get_regmap() and
rid of using struct bd9571mwv.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Acked-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The platform data header was only used to pass platform
data from board files. We now populate the regulators
exclusively from device tree, so the header contents can
be moved into the regulator drivers.
Cc: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20201205004057.1712753-2-linus.walleij@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
The struct ab8500_regulator_platform_data was a leftover
since the days before we probed all regulators from the
device tree. The ab8500-ext regulator was the only used,
defining platform data and register intialization that
was never used for anything, a copy of a boardfile no
longer in use.
Delete the ab8500_regulator_platform_data and make the
ab8500-ext regulator reference the regulator init data
in the local file directly. We are 100% device tree
these days.
Cc: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20201205004057.1712753-1-linus.walleij@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
The final step in regulator_register() is to call
regulator_resolve_supply() for each registered regulator
(including the one in the process of being registered). The
regulator_resolve_supply() function first checks if rdev->supply
is NULL, then it performs various steps to try to find the supply.
If successful, rdev->supply is set inside of set_supply().
This procedure can encounter a race condition if two concurrent
tasks call regulator_register() near to each other on separate CPUs
and one of the regulators has rdev->supply_name specified. There
is currently nothing guaranteeing atomicity between the rdev->supply
check and set steps. Thus, both tasks can observe rdev->supply==NULL
in their regulator_resolve_supply() calls. This then results in
both creating a struct regulator for the supply. One ends up
actually stored in rdev->supply and the other is lost (though still
present in the supply's consumer_list).
Here is a kernel log snippet showing the issue:
[ 12.421768] gpu_cc_gx_gdsc: supplied by pm8350_s5_level
[ 12.425854] gpu_cc_gx_gdsc: supplied by pm8350_s5_level
[ 12.429064] debugfs: Directory 'regulator.4-SUPPLY' with parent
'17a00000.rsc:rpmh-regulator-gfxlvl-pm8350_s5_level'
already present!
Avoid this race condition by holding the rdev->mutex lock inside
of regulator_resolve_supply() while checking and setting
rdev->supply.
Signed-off-by: David Collins <collinsd@codeaurora.org>
Link: https://lore.kernel.org/r/1610068562-4410-1-git-send-email-collinsd@codeaurora.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Hi,
This patch makes the LPM pin as optional as this may be controlled
in the last phase of suspend procedure to decrease the power consumption
while suspended. Along w/ this update the MAINTAINERS entry for this
driver.
Thank you,
Claudiu Beznea
Claudiu Beznea (3):
dt-bindings: regulator: mcp16502: document lpm as optional
regulator: mcp16502: lpm pin can be optional on some platforms
MAINTAINERS: add myself as maintainer for mcp16502
Documentation/devicetree/bindings/regulator/mcp16502-regulator.txt | 3 ++-
MAINTAINERS | 4 ++--
drivers/regulator/mcp16502.c | 2 +-
3 files changed, 5 insertions(+), 4 deletions(-)
--
2.7.4
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.orghttp://lists.infradead.org/mailman/listinfo/linux-arm-kernel
The ROHM PMIC regulator drivers only need the regmap pointer from
the parent device. Regmap can be obtained via dev_get_regmap()
so do not require parent to populate driver data for that.
Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Link: https://lore.kernel.org/r/20210107122355.GA35080@localhost.localdomain
Signed-off-by: Mark Brown <broonie@kernel.org>
On some platform (e.g. SAMA7G5) LPM pin should be optional as it can
be controlled explicitly (via shutdown controller registers) in the
platform specific power saving code to decrease the power consumption
while suspended as this SoC pin may be connected to other devices that
could take power saving actions based on its value.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Link: https://lore.kernel.org/r/1610028927-9842-3-git-send-email-claudiu.beznea@microchip.com
Signed-off-by: Mark Brown <broonie@kernel.org>
This series is based on v5.10-rc1.
The patchsets add support for MediaTek hardware module named DVFSRC
(dynamic voltage and frequency scaling resource collector). The DVFSRC is
a HW module which is used to collect all the requests from both software
and hardware and turn into the decision of minimum operating voltage and
minimum DRAM frequency to fulfill those requests.
So, This series is to implement the dvfsrc driver to collect all the
requests of operating voltage or DRAM bandwidth from other device drivers
likes GPU/Camera through 3 frameworks basically:
1. interconnect framework: to aggregate the bandwidth
requirements from different clients
[1] https://patchwork.kernel.org/cover/10766329/
There has a hw module "DRAM scheduler", which used to control the throughput.
The DVFSRC will collect forecast data of dram bandwidth from
SW consumers(camera/gpu...), and according the forecast to change the DRAM
frequency
2. Regualtor framework: to handle the operating voltage requirement from user or
cosumer which not belong any power domain
Changes in V6:
* Remove the performace state support, because the request from consumer can be
replaced by using interconnect and regulator framework.
* Update the DT patches and convert them to DT schema. (Georgi)
* Modify the comment format and coding style. (Mark)
Changes in V5:
* Support more platform mt6873/mt8192
* Drop the compatible and interconnect provider node and make the parent node an
interconnect provider. (Rob/Georgi)
* Make modification of interconnect driver from coding suggestion. (Georgi)
* Move interconnect diagram into the commit text of patch. (Georgi)
* Register the interconnect provider as a platform sub-device. (Georgi)
Changes in V4:
* Add acked TAG on dt-bindings patches. (Rob)
* Declaration of emi_icc_aggregate since the prototype of aggregate function
has changed meanwhile. (Georgi)
* Used emi_icc_remove instead of icc_provider_del on probe. (Georgi)
* Add dvfsrc regulator driver into series.
* Bug fixed of mt8183_get_current_level.
* Add mutex protection for pstate operation on dvfsrc_set_performance.
Changes in V3:
* Remove RFC from the subject prefix of the series
* Combine dt-binding patch and move interconnect dt-binding document into
dvfsrc. (Rob)
* Remove unused header, add unit descirption to the bandwidth, rename compatible
name on interconnect driver. (Georgi)
* Fixed some coding style: check flow, naming, used readx_poll_timeout
on dvfsrc driver. (Ryan)
* Rename interconnect driver mt8183.c to mtk-emi.c
* Rename interconnect header mtk,mt8183.h to mtk,emi.h
* mtk-scpsys.c: Add opp table check first to avoid OF runtime parse failed
Changes in RFC V2:
* Remove the DT property dram_type. (Rob)
* Used generic dts property 'opp-level' to get the performace state. (Stephen)
* Remove unecessary dependency config on Kconfig. (Stephen)
* Remove unused header file, fixed some coding style issue, typo,
error handling on dvfsrc driver. (Nicolas/Stephen)
* Remove irq handler on dvfsrc driver. (Stephen)
* Remove init table on dvfsrc driver, combine hw init on trustzone.
* Add interconnect support of mt8183 to aggregate the emi bandwidth.
(Georgi)
V5: https://patchwork.kernel.org/project/linux-mediatek/list/?series=348065
V4: https://lore.kernel.org/patchwork/cover/1209284/
V3: https://patchwork.kernel.org/cover/11118867/
RFC V2: https://lore.kernel.org/patchwork/patch/1068113/
RFC V1: https://lore.kernel.org/patchwork/cover/1028535/
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.orghttp://lists.infradead.org/mailman/listinfo/linux-arm-kernel
The ROHM PMIC regulator drivers only need the regmap pointer from
the parent device. Regmap can be obtained via dev_get_regmap()
so do not require parent to populate driver data for that.
Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Link: https://lore.kernel.org/r/20210105130221.GA3438042@localhost.localdomain
Signed-off-by: Mark Brown <broonie@kernel.org>
Driver for regulators exposed by the DVFSRC (dynamic voltage and
frequency scaling resource collector) found in devices based on
mt8183 and newer platforms.
Signed-off-by: Henry Chen <henryc.chen@mediatek.com>
Link: https://lore.kernel.org/r/1608790134-27425-12-git-send-email-henryc.chen@mediatek.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Axel Lin