Commit Graph

730 Commits

Author SHA1 Message Date
Andy Currid a2ef3a50f1 [PATCH] Fix HPET operation on 64-bit NVIDIA platforms
From: "Andy Currid" <ACurrid@nvidia.com>

This patch fixes a kernel panic during boot that occurs on NVIDIA platforms
that have HPET enabled.

When HPET is enabled, the standard timer IRQ is routed to IOAPIC pin 2 and is
advertised as such in the ACPI APIC table - but an earlier workaround in the
kernel was ignoring this override.  The fix is to honor timer IRQ overrides
from ACPI when HPET is detected on an NVIDIA platform.

Signed-off-by: Andy Currid <acurrid@nvidia.com>
Cc: "Brown, Len" <len.brown@intel.com>
Cc: "Yu, Luming" <luming.yu@intel.com>
Cc: Andi Kleen <ak@muc.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-06-08 15:12:21 -07:00
Andi Kleen 822ff019f7 [PATCH] x86_64: Don't do syscall exit tracing twice
int_ret_from_syscall already does syscall exit tracing, so
no need to do it again in the caller.

This caused problems for UML and some other special programs doing
syscall interception.

Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-05-30 20:31:06 -07:00
Robert Hentosh 7ca97c6131 [PATCH] x86_64: Fix off by one in bad_addr checking in find_e820_area
From: Robert Hentosh <robert_hentosh@dell.com>

Actually, we just stumbled on a different bug found in find_e820_area() in
e820.c.  The following code does not handle the edge condition correctly:

   while (bad_addr(&addr, size) && addr+size < ei->addr + ei->size)
       ;
   last = addr + size;
   if ( last > ei->addr + ei->size )
       continue;

The second statement in the while loop needs to be a <= b so that it is the
logical negavite of the if (a > b) outside it. It needs to read:

   while (bad_addr(&addr, size) && addr+size <= ei->addr + ei->size)
       ;

In the case that failed bad_addr was returning an address that is exactly size
bellow the end of the e820 range.

AK: Again together with the earlier avoid edma fix this fixes
boot on a Dell PE6850/16GB

Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-05-30 20:31:06 -07:00
Daniel Yeisley 0d01532451 [PATCH] x86_64: Handle empty node zero
From: Daniel Yeisley <dan.yeisley@unisys.com>

It is possible to boot a Unisys ES7000 with CPUs from multiple cells, and not
also include the memory from those cells.  This can create a scenario where
node 0 has cpus, but no associated memory.  The system will boot fine in a
configuration where node 0 has memory, but nodes 2 and 3 do not.

[AK: I rechecked the code and generic code seems to indeed handle that already.
Dan's original patch had a change for mm/slab.c that seems to be already in now.]

Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-05-30 20:31:06 -07:00
Jan Beulich b2468e525f [PATCH] x86_64: fix last_tsc calculation of PM timer
From: "Jan Beulich" <jbeulich@novell.com>

The PM timer code updates vxtime.last_tsc, but this update was done
incorrectly in two ways:
- offset_delay being in microseconds requires multiplying with cpu_mhz
  rather than cpu_khz
- the multiplication of offset_delay and cpu_khz (both being 32-bit
  values) on most current CPUs would overflow (observed value of the
  delay was approximately 4000us, yielding an overflow for frequencies
  starting a little above 1GHz)

Signed-off-by: Jan Beulich <jbeulich@novell.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-05-30 20:31:05 -07:00
Andi Kleen dc9a719528 [PATCH] x86_64: Fix no IOMMU warning in PCI-GART driver
Complaining about the IOMMU not compiled in doesn't make sense
here because it is clearly compiled in.

Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-05-30 20:31:05 -07:00
Andi Kleen 6ae53cd496 [PATCH] x86_64: Fix stack/mmap randomization for compat tasks
ia32_setup_arg_pages would ignore the passed in random stack top
and use its own static value.

Now it uses the 8bit of randomness native i386 would use too.

This indirectly fixes mmap randomization for 32bit processes too,
which depends on the stack randomization.

Should also give slightly better virtual cache colouring and
possibly better performance with HyperThreading.

Signed-off-by: Andi Kleen <ak@suse.de>
Acked-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-05-30 20:31:05 -07:00
Satoshi Oshima dc49e3445a [PATCH] kprobes: bad manipulation of 2 byte opcode on x86_64
Problem:

If we put a probe onto a callq instruction and the probe is executed,
kernel panic of Bad RIP value occurs.

Root cause:

If resume_execution() found 0xff at first byte of p->ainsn.insn, it must
check the _second_ byte.  But current resume_execution check _first_ byte
again.

I changed it checks second byte of p->ainsn.insn.

Kprobes on i386 don't have this problem, because the implementation is a
little bit different from x86_64.

Cc: Andi Kleen <ak@muc.de>
Signed-off-by: Satoshi Oshima <soshima@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-05-21 12:59:21 -07:00
Andi Kleen 40e59a6166 [PATCH] x86_64: Don't schedule on exception stack on preemptive kernels
Extends an earlier patch from John Blackwood to more exception handlers
that also run on the exception stacks.

Expand the use of preempt_conditional_{sti,cli} to all cases where
interrupts are to be re-enabled during exception handling while running
on an IST stack.

Based on original patch from Jan Beulich.

Cc: John Blackwood <john.blackwood@ccur.com>
Cc: jbeulich@novell.com
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-05-16 07:59:32 -07:00
Andi Kleen fad7906d16 [PATCH] x86_64: Fix memory hotadd heuristics
This fixes some boot failures on Dell and Unisys systems with memory
hotadd added.

 - Set hotadd_percent to 0 by default.  This means anybody using hotadd
   memory needs to specify the value on the command line.  That's
   because there are lots of Intel boxes which have a bogus hotplug area
   in their SRAT and they would waste a lot of memory before.
 - Fix calculation of how much memory to use when the hotplug area
   exceeds hotadd_percent
 - Fix fallback when the
 - Fix fallback if memory hotadd is not compiled in.

Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-05-16 07:59:31 -07:00
Andi Kleen f0fdabf8bf [PATCH] x86_64: Don't warn for overflow in nommu case when dma_mask is < 32bit
This triggers for b44's 1GB DMA workaround which tries to map
first and then bounces.

The 32bit heuristic is reasonable because the IOMMU doesn't attempt
to handle < 32bit masks anyways.

Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-05-16 07:59:31 -07:00
Andi Kleen ac71d12c99 [PATCH] x86_64: Avoid EBDA area in early boot allocator
Based on analysis&patch from Robert Hentosch

Observed on a Dell PE6850 with 16GB

The problem occurs very early on, when the kernel allocates space for the
temporary memory map called bootmap. The bootmap overlaps the EBDA region.
EBDA region is not historically reserved in the e820 mapping. When the
bootmap is freed it marks the EBDA region as usable.

If you notice in setup.c there is already code to work around the EBDA
in reserve_ebda_region(), this check however occurs after the bootmap
is allocated and doesn't prevent the bootmap from using this range.

AK: I redid the original patch. Thanks also to Jan Beulich for
spotting some mistakes.

Cc: Robert_Hentosch@dell.com
Cc: jbeulich@novell.com
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-05-08 09:34:56 -07:00
Corey Minyard 8b1ffe9550 [PATCH] x86_64: add nmi_exit to die_nmi
Playing with NMI watchdog on x86_64, I discovered that it didn't
do what I expected.  It always panic-ed, even when it didn't
happen from interrupt context.  This patch solves that
problem for me.  Also, in this case, do_exit() will be called
with interrupts disabled, I believe.  Would it be wise to also
call local_irq_enable() after nmi_exit()?
[Yes I added it -AK]

Currently, on x86_64, any NMI watchdog timeout will cause a panic
because the irq count will always be set to be in an interrupt
when do_exit() is called from die_nmi().  If we add nmi_exit() to
the die_nmi() call (since the nmi will never exit "normally")
it seems to solve this problem.  The following small program
can be used to trigger the NMI watchdog to reproduce this:
  main ()
  {
        iopl(3);
        for (;;) asm("cli");
  }

Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-05-08 09:34:56 -07:00
Corey Minyard cdc60a4c8e [PATCH] x86_64: fix die_lock nesting
I noticed this when poking around in this area.

The oops_begin() function in x86_64 would only conditionally claim
the die_lock if the call is nested, but oops_end() would always
release the spinlock. This patch adds a nest count for the die lock
so that the release of the lock is only done on the final oops_end().

Signed-off-by: Corey Minyard <minyard@acm.org>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-05-08 09:34:56 -07:00
Andi Kleen 5192d84e4c [PATCH] x86_64: Check for too many northbridges in IOMMU code
The IOMMU code can only deal with 8 northbridges. Error out when
more are found.

Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-05-08 09:34:56 -07:00
Kimball Murray e0c1e9bf81 [PATCH] x86_64: avoid IRQ0 ioapic pin collision
The patch addresses a problem with ACPI SCI interrupt entry, which gets
re-used, and the IRQ is assigned to another unrelated device.  The patch
corrects the code such that SCI IRQ is skipped and duplicate entry is
avoided.  Second issue came up with VIA chipset, the problem was caused by
original patch assigning IRQs starting 16 and up.  The VIA chipset uses
4-bit IRQ register for internal interrupt routing, and therefore cannot
handle IRQ numbers assigned to its devices.  The patch corrects this
problem by allowing PCI IRQs below 16.

Cc: len.brown@intel.com

Signed-off by: Natalie Protasevich <Natalie.Protasevich@unisys.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-05-08 09:34:56 -07:00
Linus Torvalds 532f57da40 Merge branch 'audit.b10' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/audit-current
* 'audit.b10' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/audit-current:
  [PATCH] Audit Filter Performance
  [PATCH] Rework of IPC auditing
  [PATCH] More user space subject labels
  [PATCH] Reworked patch for labels on user space messages
  [PATCH] change lspp ipc auditing
  [PATCH] audit inode patch
  [PATCH] support for context based audit filtering, part 2
  [PATCH] support for context based audit filtering
  [PATCH] no need to wank with task_lock() and pinning task down in audit_syscall_exit()
  [PATCH] drop task argument of audit_syscall_{entry,exit}
  [PATCH] drop gfp_mask in audit_log_exit()
  [PATCH] move call of audit_free() into do_exit()
  [PATCH] sockaddr patch
  [PATCH] deal with deadlocks in audit_free()
2006-05-01 21:43:05 -07:00
Mikael Pettersson 160bd18e5e [PATCH] x86_64: make PC Speaker driver work
The PC Speaker driver's ->probe() routine doesn't even get called in the
64-bit kernels.  The reason for that is that the arch code apparently has
to explictly add a "pcspkr" platform device in order for the driver core to
call the ->probe() routine.  arch/i386/kernel/setup.c unconditionally adds
a "pcspkr" device, but the x86_64 kernel has no code at all related to the
PC Speaker.

The patch below copies the relevant code from i386 to x86_64, which makes
the PC Speaker work for me on x86_64.

Cc: Dmitry Torokhov <dtor_core@ameritech.net>
Acked-by: Andi Kleen <ak@muc.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-05-01 18:17:47 -07:00
Andi Kleen d261020229 [PATCH] x86_64: Add compat_sys_vmsplice and use it in x86-64
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-05-01 18:17:43 -07:00
Al Viro 5411be59db [PATCH] drop task argument of audit_syscall_{entry,exit}
... it's always current, and that's a good thing - allows simpler locking.

Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
2006-05-01 06:06:18 -04:00
Chandra Seetharaman 83d722f7e1 [PATCH] Remove __devinit and __cpuinit from notifier_call definitions
Few of the notifier_chain_register() callers use __init in the definition
of notifier_call.  It is incorrect as the function definition should be
available after the initializations (they do not unregister them during
initializations).

This patch fixes all such usages to _not_ have the notifier_call __init
section.

Signed-off-by: Chandra Seetharaman <sekharan@us.ibm.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-04-26 08:30:03 -07:00
Mike Waychison 5b20192727 [PATCH] x86_64: Fix a race in the free_iommu path
We do this by removing a micro-optimization that tries to avoid grabbing
the iommu_bitmap_lock spinlock and using a bus-locked operation.

This still races with other simultaneous alloc_iommu or free_iommu(size >
1) which both use bus-unlocked operations.

The end result of this race is eventually ending up with an
iommu_gart_bitmap that has bits errornously set all over, making large
contiguous iommu space allocations fail with 'PCI-DMA: Out of IOMMU space'.

Signed-off-by: Mike Waychison <mikew@google.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-04-22 09:19:52 -07:00
Andi Kleen ddbe3eec59 [PATCH] x86_64: Pass -32 to the assembler when compiling the 32bit vsyscall pages
This quietens warnings and actually fixes a bug.  The unwind tables would
come out wrong without -32, causing pthread cancellation during them to
crash in the gcc runtime.

The problem seems to only happen with newer binutils (it doesn't happen
with 2.16.91.0.2 but happens wit 2.16.91.0.5)

Thanks to David Altobelli <david.altobelli@hp.com> and Brian Baker
<Brian.B@hp.com> for test case and initial analysis.

Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-04-22 09:19:52 -07:00
Andy Whitcroft 3b5fd59fdd [PATCH] x86_64: sparsemem does not need node_mem_map
Seems we are trying to init the node_mem_map when we don't need to, for
example when SPARSEMEM is enabled.  This causes the error below during
compilation.  Use CONFIG_FLAT_NODE_MEM_MAP to gate allocation and init.

  arch/x86_64/mm/numa.c: In function `setup_node_zones':
  arch/x86_64/mm/numa.c:191: error: structure has no member
                                                  named `node_mem_map'

Signed-off-by: Andy Whitcroft <apw@shadowen.org>
Acked-by: Andi Kleen <ak@muc.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-04-22 09:19:52 -07:00
Andi Kleen 18bd057b14 [PATCH] i386/x86-64: Fix x87 information leak between processes
AMD K7/K8 CPUs only save/restore the FOP/FIP/FDP x87 registers in FXSAVE
when an exception is pending.  This means the value leak through
context switches and allow processes to observe some x87 instruction
state of other processes.

This was actually documented by AMD, but nobody recognized it as
being different from Intel before.

The fix first adds an optimization: instead of unconditionally
calling FNCLEX after each FXSAVE test if ES is pending and skip
it when not needed. Then do a x87 load from a kernel variable to
clear FOP/FIP/FDP.

This means other processes always will only see a constant value
defined by the kernel in their FP state.

I took some pain to make sure to chose a variable that's already
in L1 during context switch to make the overhead of this low.

Also alternative() is used to patch away the new code on CPUs
who don't need it.

Patch for both i386/x86-64.

The problem was discovered originally by Jan Beulich. Richard
Brunner provided the basic code for the workarounds, with contribution
from Jan.

This is CVE-2006-1056

Cc: richard.brunner@amd.com
Cc: jbeulich@novell.com

Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-04-20 07:58:11 -07:00
Prasanna S Panchamukhi 3b60211c16 [PATCH] Switch Kprobes inline functions to __kprobes for x86_64
Andrew Morton pointed out that compiler might not inline the functions
marked for inline in kprobes.  There-by allowing the insertion of probes
on these kprobes routines, which might cause recursion.

This patch removes all such inline and adds them to kprobes section
there by disallowing probes on all such routines.  Some of the routines
can even still be inlined, since these routines gets executed after the
kprobes had done necessay setup for reentrancy.

Signed-off-by: Prasanna S Panchamukhi <prasanna@in.ibm.com>
Cc: Andi Kleen <ak@muc.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-04-19 09:13:53 -07:00
Andi Kleen f1233ab2ce [PATCH] x86_64: Add tee and sync_file_range
tee was already there for some reason for native 64bit, but
sys_sync_file_range was missing. Also add it to the compat layer.

Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-04-18 10:39:20 -07:00
Vivek Goyal 8bcc5280e6 [PATCH] x86_64: x86_64 add crashdump trigger points
o Start booting into the capture kernel after an Oops if system is in a
  unrecoverable state. System will boot into the capture kernel, if one is
  pre-loaded by the user, and capture the kernel core dump.

o One of the following conditions should be true to trigger the booting of
  capture kernel.
        - panic_on_oops is set.
        - pid of current thread is 0
        - pid of current thread is 1
        - Oops happened inside interrupt context.

Signed-off-by: Vivek Goyal <vgoyal@in.ibm.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-04-18 10:39:19 -07:00
Andi Kleen d16e86243e [PATCH] x86_64: Update defconfig
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-04-18 10:39:19 -07:00
Bjorn Helgaas 4f705ae3e9 [PATCH] DMI: move dmi_scan.c from arch/i386 to drivers/firmware/
dmi_scan.c is arch-independent and is used by i386, x86_64, and ia64.
Currently all three arches compile it from arch/i386, which means that ia64
and x86_64 depend on things in arch/i386 that they wouldn't otherwise care
about.

This is simply "mv arch/i386/kernel/dmi_scan.c drivers/firmware/" (removing
trailing whitespace) and the associated Makefile changes.  All three
architectures already set CONFIG_DMI in their top-level Kconfig files.

Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Cc: Andi Kleen <ak@muc.de>
Cc: "Luck, Tony" <tony.luck@intel.com>
Cc: Andrey Panin <pazke@orbita1.ru>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2006-04-14 11:41:25 -07:00
Andi Kleen 44b940c299 [PATCH] x86_64: Fix embarassing typo in mmconfig bus check
Surprising that it still worked at all with this - yes it was
tested.

Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-04-11 06:38:57 -07:00
Andi Kleen ecc16ba96f [PATCH] i386/x86-64: Remove checks for value == NULL in PCI config space access
Nobody should pass NULL here. Could in theory make it a BUG,
but the NULL pointer oops will do as well.

Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-04-11 06:38:57 -07:00
Andi Kleen 97a4d00388 [PATCH] x86_64: Remove check for canonical RIP
As pointed out by Linus it is useless now because entry.S should
handle it correctly in all cases.

Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-04-11 06:38:57 -07:00
Antonino A. Daplas 89ec4c238e [PATCH] vesafb: Fix incorrect logo colors in x86_64
Bugzilla Bug 6299:

A pixel size of 8 bits produces wrong logo colors in x86_64.

The driver has 2 methods for setting the color map, using the protected
mode interface provided by the video BIOS and directly writing to the VGA
registers.  The former is not supported in x86_64 and the latter is enabled
only in i386.

Fix by enabling the latter method in x86_64 only if supported by the BIOS.
If both methods are unsupported, change the visual of vesafb to
STATIC_PSEUDOCOLOR.

Signed-off-by: Antonino Daplas <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-04-11 06:18:54 -07:00
Kyle McMartin 894b5779ce [PATCH] No arch-specific strpbrk implementations
While cleaning up parisc_ksyms.c earlier, I noticed that strpbrk wasn't
being exported from lib/string.c.  Investigating further, I noticed a
changeset that removed its export and added it to _ksyms.c on a few more
architectures.  The justification was that "other arches do it."

I think this is wrong, since no architecture currently defines
__HAVE_ARCH_STRPBRK, there's no reason for any of them to be exporting it
themselves.  Therefore, consolidate the export to lib/string.c.

Signed-off-by: Kyle McMartin <kyle@parisc-linux.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-04-11 06:18:40 -07:00
Yasunori Goto c80d79d746 [PATCH] Configurable NODES_SHIFT
Current implementations define NODES_SHIFT in include/asm-xxx/numnodes.h for
each arch.  Its definition is sometimes configurable.  Indeed, ia64 defines 5
NODES_SHIFT values in the current git tree.  But it looks a bit messy.

SGI-SN2(ia64) system requires 1024 nodes, and the number of nodes already has
been changeable by config.  Suitable node's number may be changed in the
future even if it is other architecture.  So, I wrote configurable node's
number.

This patch set defines just default value for each arch which needs multi
nodes except ia64.  But, it is easy to change to configurable if necessary.

On ia64 the number of nodes can be already configured in generic ia64 and SN2
config.  But, NODES_SHIFT is defined for DIG64 and HP'S machine too.  So, I
changed it so that all platforms can be configured via CONFIG_NODES_SHIFT.  It
would be simpler.

See also: http://marc.theaimsgroup.com/?l=linux-kernel&m=114358010523896&w=2

Signed-off-by: Yasunori Goto <y-goto@jp.fujitsu.com>
Cc: Hirokazu Takata <takata@linux-m32r.org>
Cc: "Luck, Tony" <tony.luck@intel.com>
Cc: Andi Kleen <ak@muc.de>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Cc: Richard Henderson <rth@twiddle.net>
Cc: Kyle McMartin <kyle@mcmartin.ca>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Jack Steiner <steiner@sgi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-04-11 06:18:39 -07:00
Andi Kleen b8feb47f99 [PATCH] x86_64: Update 32-bit system call table
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-04-09 11:53:53 -07:00
Andi Kleen 67d53ea5a3 [PATCH] x86_64: Eliminate IA32_NR_syscalls define
Or rather compute it based on the table length automatically.

This also has the intended side effect of not warning for new system calls
anymore.

Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-04-09 11:53:53 -07:00
Sam Ravnborg bbd3aff89d [PATCH] x86_64: fix CONFIG_REORDER
Fix CONFIG_REORDER.

The value of cflags-y was assined to CFLAGS before cflags-y was assigned
the value used for CONFIG_REORDER.

Use cflags-y for all CFLAGS options in the Makefile to avoid this
happening again.

Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-04-09 11:53:53 -07:00
John Blackwood 97c2803c9c [PATCH] x86_64: Plug GS leak in arch_prctl()
In linux-2.6.16, we have noticed a problem where the gs base value
returned from an arch_prtcl(ARCH_GET_GS, ...) call will be incorrect if:

   - the current/calling task has NOT set its own gs base yet to a
     non-zero value,

   - some other task that ran on the same processor previously set their
     own gs base to a non-zero value.

In this situation, the ARCH_GET_GS code will read and return the
MSR_KERNEL_GS_BASE msr register.

However, since the __switch_to() code does NOT load/zero the
MSR_KERNEL_GS_BASE register when the task that is switched IN has a zero
next->gs value, the caller of arch_prctl(ARCH_GET_GS, ...) will get back
the value of some previous tasks's gs base value instead of 0.

    Change the arch_prctl() ARCH_GET_GS code to only read and return
    the MSR_KERNEL_GS_BASE msr register if the 'gs' register of the calling
    task is non-zero.

    Side note: Since in addition to using arch_prctl(ARCH_SET_GS, ...),
    a task can also setup a gs base value by using modify_ldt() and write
    an index value into 'gs' from user space, the patch below reads
    'gs' instead of using thread.gs, since in the modify_ldt() case,
    the thread.gs value will be 0, and incorrect value would be returned
    (the task->thread.gs value).

    When the user has not set its own gs base value and the 'gs'
    register is zero, then the MSR_KERNEL_GS_BASE register will not be
    read and a value of zero will be returned by reading and returning
    'task->thread.gs'.

    The first patch shown below is an attempt at implementing this
    approach.

Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-04-09 11:53:53 -07:00
Jordan Hargrave b20367a6c2 [PATCH] x86_64: Fix drift with HPET timer enabled
If the HPET timer is enabled, the clock can drift by ~3 seconds a day.
This is due to the HPET timer not being initialized with the correct
setting (still using PIT count).

If HZ changes, this drift can become even more pronounced.

HPET patch initializes tick_nsec with correct tick_nsec settings for
HPET timer.

Vojtech comments:

  "It's not entirely correct (it assumes the HPET ticks totally
   exactly), but it's significantly better than assuming the PIT error
   there."

Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-04-09 11:53:53 -07:00
Andi Kleen 49c93e84d8 [PATCH] i386/x86-64: Return defined error value for bad PCI config space accesses
Mostly to get better handling when a extended config space
access has to fallback to Type1.

Cc: gregkh@suse.de
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-04-09 11:53:52 -07:00
Andi Kleen 8c30b1a74a [PATCH] i386/x86_64: Check if MCFG works for the first 16 busses
Previously only the first bus would be checked against Type 1.

Why 16? Checking all would need too much memory and we
can assume that systems with more than 16 busses have better than
average quality BIOS.

This is an additional defense against bad MCFG tables.

Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-04-09 11:53:52 -07:00
Ravikiran G Thirumalai e405d06729 [PATCH] x86_64: Fixup read_mostly section on internode cache line size for vSMP
Fixup the read mostly section to start at internode cacheline boundary.

Signed-off-by: Ravikiran Thirumalai <kiran@scalex86.org>
Signed-off-by: Shai Fultheim <shai@scalex86.org>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-04-09 11:53:52 -07:00
Andi Kleen 3d34ee6891 [PATCH] x86_64: Don't return error for HPET initialization in initcall
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-04-09 11:53:52 -07:00
Andi Kleen ac04dcaf6f [PATCH] x86_64: Don't export strlen twice
Fix

  WARNING: vmlinux: 'strlen' exported twice. Previous export was in vmlinux

Reported by Mats Johannesson

Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-04-09 11:53:52 -07:00
Andi Kleen 7bf36bbc5e [PATCH] x86_64: When user could have changed RIP always force IRET
Intel EM64T CPUs handle uncanonical return addresses differently
from AMD CPUs.

The exception is reported in the SYSRET, not the next instruction.
This leads to the kernel exception handler running on the user stack
with the wrong GS because the kernel didn't expect exceptions
on this instruction.

This version of the patch has the teething problems that plagued an earlier
version fixed.

This is CVE-2006-0744

Thanks to Ernie Petrides and Asit B. Mallick for analysis and initial
patches.

Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-04-09 11:53:52 -07:00
Andi Kleen 553f265fe8 [PATCH] x86_64: Don't run NMI watchdog during machine checks
Machine checks can stall the machine for a long time and
it's not good to trigger the nmi watchdog during that.

Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-04-09 11:53:52 -07:00
Andi Kleen d1530d82e0 [PATCH] x86_64: Clear APIC feature bit when local APIC is disabled
Needed for other checks later in ACPI.

Pointed out by Len Brown

Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-04-09 11:53:51 -07:00
Andi Kleen fa47dd0ba3 [PATCH] x86_64: Fix compilation with CONFIG_PCI=n / allnoconfig
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-04-09 11:53:51 -07:00