This commit takes ALSA fireface driver to perform sequence replay for
media clock recovery.
The protocol specific to RME Fireface series is not compliant to
IEC 61883-1/6 since it has no CIP header, therefore presentation time
is not used for media clock recovery. The sequence of the number of data
blocks per packet is important.
I note that the device skips an isochronous cycle corresponding to an
empty packet or a NODATA packet in blocking transmission method of
IEC 61883-1/6. For sequence replay, the cycle is handled as receiving an
empty packet. Furthermore, it doesn't start packet transmission till
receiving any packet.
The sequence replay is tested with below models:
* Fireface 400
* Fireface 800
* Fireface 802
I note that it is better to initialize Fireface 400 in advance by
initialization transaction implemented in snd-fireface-ctl-service of
snd-firewire-ctl-services project. You can see whether initialized or
not by HOST LED on the device. Unless, the device often stops packet
transmission even if session starts.
I guess the sequence replay also works well with below models:
* Fireface UFX
* Fireface UCX
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Link: https://lore.kernel.org/r/20210531025103.17880-7-o-takashi@sakamocchi.jp
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Models in below series start transmission of packet after receiving the
sequence of packets:
* Digidesign Digi00x family
* RME Fireface series
Additionally, models in Tascam FireWire series start multiplexing PCM
frames into packets enough after receiving packets. It's required to
transfer packets on-the-fly for the above models according to nominal
sampling transfer frequency before starting sequence replay.
This commit allows drivers to decide whether the engine transfers packet
on-the-fly or not.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Link: https://lore.kernel.org/r/20210527122611.173711-4-o-takashi@sakamocchi.jp
Signed-off-by: Takashi Iwai <tiwai@suse.de>
In design of audio and music unit in IEEE 1394 bus, feedback of
effective sampling transfer frequency (STF) is delivered by packets
transferred from device. The devices supported by ALSA firewire stack
are categorized to three groups regarding to it.
* Group 1:
* Echo Audio Fireworks board module
* Oxford Semiconductor OXFW971 ASIC
* Digidesign Digi00x family
* Tascam FireWire series
* RME Fireface series
* Group 2:
* BridgeCo. DM1000/DM1100/DM1500 ASICs for BeBoB solution
* TC Applied Technologies DICE ASICs
* Group 3:
* Mark of the Unicord FireWire series
In group 1, the effective STF is determined by the sequence of the number
of events per packet. In group 2, the sequence of presentation timestamp
expressed in syt field of CIP header is interpreted as well. In group 3,
the presentation timestamp is expressed in source packet header (SPH) of
each data block.
I note that some models doesn't take care of effective STF with large
internal buffer. It's reasonable to name it as group 0:
* Group 0
* Oxford Semiconductor OXFW970 ASIC
The effective STF is known to be slightly different from nominal STF for
all of devices, and to be different between the devices. Furthermore, the
effective STF is known to be shifted for long-period transmission. This
makes it hard for software to satisfy the effective STF when processing
packets to the device.
The effective STF is deterministic as a result of analyzing the batch of
packet transferred from the device. For the analysis, caching the sequence
of parameter in the packet is required.
This commit adds an option so that AMDTP domain structure takes AMDTP
stream structure to cache the sequence of parameters in packet transferred
from the device. The parameters are offset ticks of syt field against the
cycle to receive the packet and the number of data blocks per packet.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Link: https://lore.kernel.org/r/20210527122611.173711-2-o-takashi@sakamocchi.jp
Signed-off-by: Takashi Iwai <tiwai@suse.de>
When starting AMDTP domain, tasks in process context yields running CPU
till all of isochronous context get callback, with an assumption that
it's OK to process content of packet.
However several isochronous cycles are skipped to transfer rx packets, or
the content of rx packets are dropped, to manage the timing to start
processing the packets.
This commit changes the timing for tasks in process context to wake up
when processing content of packet is actually ready.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Link: https://lore.kernel.org/r/20210520040154.80450-9-o-takashi@sakamocchi.jp
Signed-off-by: Takashi Iwai <tiwai@suse.de>
In the latter models of RME Fireface series, device start to transfer
packets several dozens of milliseconds. On the other hand, ALSA fireface
driver starts IR context 2 milliseconds after the start. This results
in loss to handle incoming packets on the context.
This commit changes to start IR context immediately instead of
postponement. For Fireface 800, this affects nothing because the device
transfer packets 100 milliseconds or so after the start and this is
within wait timeout.
Cc: <stable@vger.kernel.org>
Fixes: acfedcbe1c ("ALSA: firewire-lib: postpone to start IR context")
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Link: https://lore.kernel.org/r/20200510074301.116224-3-o-takashi@sakamocchi.jp
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Some devices have a quirk to postpone transmission of isoc packet for
several dozen or hundred isoc cycles since configured to transmit.
Furthermore, some devices have a quirk to transmit isoc packet with
discontinued data of its header.
In 1394 OHCI specification, software allows to start isoc context with
certain isoc cycle. Linux firewire subsystem has kernel API to use it
as well.
This commit uses the functionality of 1394 OHCI controller to handle
the quirks. At present, this feature is convenient to ALSA bebob and
fireface driver. As a result, some devices can be safely handled, as
long as I know:
- MAudio FireWire solo
- MAudio ProFire Lightbridge
- MAudio FireWire 410
- Roland FA-66
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Link: https://lore.kernel.org/r/20191018061911.24909-7-o-takashi@sakamocchi.jp
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This commit allows ALSA fireface driver to share PCM buffer size for
both capture and playback PCM substream. When AMDTP domain starts for
one of the PCM substream, buffer size of the PCM substream is stores to
AMDTP domain structure. Some AMDTP streams have already run with the
buffer size when another PCM substream starts, therefore the PCM
substream has a constraint to its buffer size.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Link: https://lore.kernel.org/r/20191017155424.885-10-o-takashi@sakamocchi.jp
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The number of packets in packet buffer has been fixed number (=48) since
first commit of ALSA IEC 61883-1/6 packet streaming engine.
This commit allows the engine to use variable number of packets in the
buffer. The size is calculated by a parameter in AMDTP domain structure
surely to store the number of events in the packets of buffer. Although
the value of parameter is expected to come from 'period size' parameter
of PCM substream, at present 48 is still used.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Link: https://lore.kernel.org/r/20191017155424.885-2-o-takashi@sakamocchi.jp
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This commit is a preparation to share the size of PCM period between
PCM substreams on AMDTP streams in the same domain. At this time,
the size of PCM period in PCM substream which starts AMDTP streams in the
same domain is recorded.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Link: https://lore.kernel.org/r/20191007110532.30270-10-o-takashi@sakamocchi.jp
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This commit is a preparation to support AMDTP domain.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This is a very big update, mainly thanks to Morimoto-san's refactoring
work and some fairly large new drivers.
- Lots more work on moving towards a component based framework from
Morimoto-san.
- Support for force disconnecting muxes from Jerome Brunet.
- New drivers for Cirrus Logic CS47L35, CS47L85 and CS47L90, Conexant
CX2072X, Realtek RT1011 and RT1308.
-----BEGIN PGP SIGNATURE-----
iQFHBAABCgAxFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAl0jGwUTHGJyb29uaWVA
a2VybmVsLm9yZwAKCRAk1otyXVSH0LD4B/9AkutfS+vznOrk0V0wFb2SUfjwE4Pr
+z/kAehohAOl/7pg9Dun/lmZYBWMyOM2aYmK81ahEo2DfO+uzwkwjCaXFjGVGwEK
j7XpWkrIjKnou/z1FeALgVvt+crzdy5iNWC04AbKaP2WHCcI7zvPQIsBta/V0OJt
lg+j0J7pagnTMcgV1+qJdaASmofy/hpoZ79Gv0PIfGC8hpJ/3mBgcNPCLQrJtD4R
v+tzvCZNrZVqCanwLf3vouEm1bpWYOpI+Wdmu4u6rY7MhmCj72EJ2zyfdm/qtaxF
e7whgCyOQFkWe7NgDn0G08aAT6LsaxOtPNr7H8tL8S8sw8425fqeOouV
=n/HQ
-----END PGP SIGNATURE-----
Merge tag 'asoc-v5.3' of https://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-linus
ASoC: Updates for v5.3
This is a very big update, mainly thanks to Morimoto-san's refactoring
work and some fairly large new drivers.
- Lots more work on moving towards a component based framework from
Morimoto-san.
- Support for force disconnecting muxes from Jerome Brunet.
- New drivers for Cirrus Logic CS47L35, CS47L85 and CS47L90, Conexant
CX2072X, Realtek RT1011 and RT1308.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
>From callbacks for pcm and rawmidi interfaces, the functions to stop
and release duplex streams are called at the same time. This commit
merges the two functions.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The operation to finish packet streaming corresponds to stopping
isochronous contexts.
This commit applies code refactoring to move codes to stop into
a helper function to finish the session.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
After bus reset, isochronous resource manager releases all of allocated
isochronous resources. The nodes to restart packet streaming should
request reallocation of the resources.
However, between the bus-reset and invocation of 'struct fw_driver.update'
handler, ALSA PCM application can detect this situation by XRUN because
the target device cancelled to transmit packets once bus-reset occurs.
Due to the above mechanism, ALSA fireface driver just stops packet
streaming in the update handler, thus pcm.prepare handler should
request the reallocation.
This commit requests the reallocation in pcm.prepare callback when
bus generation is changed.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Once allocated, isochronous resources are available for packet
streaming, even if the streaming is cancelled. For this reason,
current implementation handles allocation of the resources and
starting packet streaming at the same time. However, this brings
complicated procedure to start packet streaming.
This commit separates the allocation and starting. The allocation is
done in pcm.hw_params callback and available till pcm.hw_free callback.
Even if any XRUN occurs, pcm.prepare callback is done to restart
packet streaming for allocated the resources.
There are two points to stop packet streaming; in pcm.hw_params and
pcm.prepare callbacks.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This commit is a part of preparation to perform allocation/release
of isochronous channels in pcm.hw_params/hw_free callbacks.
In ALSA fireface driver, the allocation of isochronous resources is
programmed in each implementation of protocol. This commit adds
protocol-specific operation for the allocation separated from
the operation to begin session.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Based on 1 normalized pattern(s):
licensed under the terms of the gnu general public license version 2
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 88 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Alexios Zavras <alexios.zavras@intel.com>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190530000437.521539229@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This commit adds a member for a callback function to get clock status
to former protocol.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This commit adds a member for a callback function to switch frame
fetching mode to former protocol.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The way to maintain isochronous resources on bus is different between
Fireface 400/800.
This commit is a preparation. This commit moves a function to allocate resource to
model-dependent implementation.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Fireface 400/800 use three modes against the number of data channels in
data block for both tx/rx packets.
This commit adds refactoring for it. Some enumerators are added to
represent each of mode and a function is added to calculate the mode
from sampling frequency code (sfc).
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Both of Fireface 400/800 have the same register to switch frame fetching
mode regardless of difference of available number of PCM frames in
rx isochronous packet.
This commit moves a helper function from model-dependent implementation.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
As long as investigating packet dumps from Fireface 400/800, bits on
status registers for clock synchronization are the same.
This commit moves a parser for a register of clock configuration to
obsolete model-specific operations.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This commit adds hwdep interface so as the other drivers for audio and
music units on IEEE 1394 have.
This interface is designed for mixer/control applications. By using this
interface, an application can get information about firewire node, can
lock/unlock kernel streaming and can get notification at starting/stopping
kernel streaming.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This commit adds management functionality for packet streaming.
As long as investigating Fireface 400, there're three modes depending
on sampling transmission frequency. The number of data channels in each
data block is different depending on the mode. The set of available
data channels for each mode might be different for each protocol and
model.
The length of registers for the number of isochronous channel is just
three bits, therefore 0-7ch are available.
When bus reset occurs on IEEE 1394 bus, the device discontinues to
transmit packets. This commit aborts PCM substreams at bus reset handler.
As I described in followed commits, The device manages its sampling clock
independently of sampling transmission frequency against IEC 61883-6.
Thus, it's a lower cost to change the sampling transmission frequency,
while data fetch between streaming layer and DSP require larger buffer
for resampling. As a result, device latency might tend to be larger than
ASICs for IEC 61883-1/6 such as DM1000/DM1100/DM1500 (BeBoB),
DiceII/TCD2210/TCD2220/TCD3070 and OXFW970/971.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Takashi Sakamoto