acrn-kernel/net/tipc/ib_media.c

102 lines
3.6 KiB
C
Raw Normal View History

tipc: add InfiniBand media type Add InfiniBand media type based on the ethernet media type. The only real difference is that in case of InfiniBand, we need the entire 20 bytes of space reserved for media addresses, so the TIPC media type ID is not explicitly stored in the packet payload. Sample output of tipc-config: # tipc-config -v -addr -netid -nt=all -p -m -b -n -ls node address: <10.1.4> current network id: 4711 Type Lower Upper Port Identity Publication Scope 0 167776257 167776257 <10.1.1:1855512577> 1855512578 cluster 167776260 167776260 <10.1.4:1216454657> 1216454658 zone 1 1 1 <10.1.4:1216479235> 1216479236 node Ports: 1216479235: bound to {1,1} 1216454657: bound to {0,167776260} Media: eth ib Bearers: ib:ib0 Nodes known: <10.1.1>: up Link <broadcast-link> Window:20 packets RX packets:0 fragments:0/0 bundles:0/0 TX packets:0 fragments:0/0 bundles:0/0 RX naks:0 defs:0 dups:0 TX naks:0 acks:0 dups:0 Congestion bearer:0 link:0 Send queue max:0 avg:0 Link <10.1.4:ib0-10.1.1:ib0> ACTIVE MTU:2044 Priority:10 Tolerance:1500 ms Window:50 packets RX packets:80 fragments:0/0 bundles:0/0 TX packets:40 fragments:0/0 bundles:0/0 TX profile sample:22 packets average:54 octets 0-64:100% -256:0% -1024:0% -4096:0% -16384:0% -32768:0% -66000:0% RX states:410 probes:213 naks:0 defs:0 dups:0 TX states:410 probes:197 naks:0 acks:0 dups:0 Congestion bearer:0 link:0 Send queue max:1 avg:0 Signed-off-by: Patrick McHardy <kaber@trash.net> Signed-off-by: David S. Miller <davem@davemloft.net>
2013-04-17 14:18:28 +08:00
/*
* net/tipc/ib_media.c: Infiniband bearer support for TIPC
*
* Copyright (c) 2013 Patrick McHardy <kaber@trash.net>
*
* Based on eth_media.c, which carries the following copyright notice:
*
* Copyright (c) 2001-2007, Ericsson AB
* Copyright (c) 2005-2008, 2011, Wind River Systems
* All rights reserved.
*
* Redistribution and use in source and binary forms, with or without
* modification, are permitted provided that the following conditions are met:
*
* 1. Redistributions of source code must retain the above copyright
* notice, this list of conditions and the following disclaimer.
* 2. Redistributions in binary form must reproduce the above copyright
* notice, this list of conditions and the following disclaimer in the
* documentation and/or other materials provided with the distribution.
* 3. Neither the names of the copyright holders nor the names of its
* contributors may be used to endorse or promote products derived from
* this software without specific prior written permission.
*
* Alternatively, this software may be distributed under the terms of the
* GNU General Public License ("GPL") version 2 as published by the Free
* Software Foundation.
*
* THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS"
* AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
* IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE
* ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT OWNER OR CONTRIBUTORS BE
* LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR
* CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF
* SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS
* INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN
* CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE)
* ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
* POSSIBILITY OF SUCH DAMAGE.
*/
#include <linux/if_infiniband.h>
#include "core.h"
#include "bearer.h"
tipc: improve and extend media address conversion functions TIPC currently handles two media specific addresses: Ethernet MAC addresses and InfiniBand addresses. Those are kept in three different formats: 1) A "raw" format as obtained from the device. This format is known only by the media specific adapter code in eth_media.c and ib_media.c. 2) A "generic" internal format, in the form of struct tipc_media_addr, which can be referenced and passed around by the generic media- unaware code. 3) A serialized version of the latter, to be conveyed in neighbor discovery messages. Conversion between the three formats can only be done by the media specific code, so we have function pointers for this purpose in struct tipc_media. Here, the media adapters can install their own conversion functions at startup. We now introduce a new such function, 'raw2addr()', whose purpose is to convert from format 1 to format 2 above. We also try to as far as possible uniform commenting, variable names and usage of these functions, with the purpose of making them more comprehensible. We can now also remove the function tipc_l2_media_addr_set(), whose job is done better by the new function. Finally, we expand the field for serialized addresses (format 3) in discovery messages from 20 to 32 bytes. This is permitted according to the spec, and reduces the risk of problems when we add new media in the future. Signed-off-by: Jon Maloy <jon.maloy@ericsson.com> Reviewed-by: Ying Xue <ying.xue@windriver.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-05-14 17:39:13 +08:00
/* convert InfiniBand address (media address format) media address to string */
static int tipc_ib_addr2str(struct tipc_media_addr *a, char *str_buf,
int str_size)
tipc: add InfiniBand media type Add InfiniBand media type based on the ethernet media type. The only real difference is that in case of InfiniBand, we need the entire 20 bytes of space reserved for media addresses, so the TIPC media type ID is not explicitly stored in the packet payload. Sample output of tipc-config: # tipc-config -v -addr -netid -nt=all -p -m -b -n -ls node address: <10.1.4> current network id: 4711 Type Lower Upper Port Identity Publication Scope 0 167776257 167776257 <10.1.1:1855512577> 1855512578 cluster 167776260 167776260 <10.1.4:1216454657> 1216454658 zone 1 1 1 <10.1.4:1216479235> 1216479236 node Ports: 1216479235: bound to {1,1} 1216454657: bound to {0,167776260} Media: eth ib Bearers: ib:ib0 Nodes known: <10.1.1>: up Link <broadcast-link> Window:20 packets RX packets:0 fragments:0/0 bundles:0/0 TX packets:0 fragments:0/0 bundles:0/0 RX naks:0 defs:0 dups:0 TX naks:0 acks:0 dups:0 Congestion bearer:0 link:0 Send queue max:0 avg:0 Link <10.1.4:ib0-10.1.1:ib0> ACTIVE MTU:2044 Priority:10 Tolerance:1500 ms Window:50 packets RX packets:80 fragments:0/0 bundles:0/0 TX packets:40 fragments:0/0 bundles:0/0 TX profile sample:22 packets average:54 octets 0-64:100% -256:0% -1024:0% -4096:0% -16384:0% -32768:0% -66000:0% RX states:410 probes:213 naks:0 defs:0 dups:0 TX states:410 probes:197 naks:0 acks:0 dups:0 Congestion bearer:0 link:0 Send queue max:1 avg:0 Signed-off-by: Patrick McHardy <kaber@trash.net> Signed-off-by: David S. Miller <davem@davemloft.net>
2013-04-17 14:18:28 +08:00
{
if (str_size < 60) /* 60 = 19 * strlen("xx:") + strlen("xx\0") */
return 1;
sprintf(str_buf, "%20phC", a->value);
tipc: add InfiniBand media type Add InfiniBand media type based on the ethernet media type. The only real difference is that in case of InfiniBand, we need the entire 20 bytes of space reserved for media addresses, so the TIPC media type ID is not explicitly stored in the packet payload. Sample output of tipc-config: # tipc-config -v -addr -netid -nt=all -p -m -b -n -ls node address: <10.1.4> current network id: 4711 Type Lower Upper Port Identity Publication Scope 0 167776257 167776257 <10.1.1:1855512577> 1855512578 cluster 167776260 167776260 <10.1.4:1216454657> 1216454658 zone 1 1 1 <10.1.4:1216479235> 1216479236 node Ports: 1216479235: bound to {1,1} 1216454657: bound to {0,167776260} Media: eth ib Bearers: ib:ib0 Nodes known: <10.1.1>: up Link <broadcast-link> Window:20 packets RX packets:0 fragments:0/0 bundles:0/0 TX packets:0 fragments:0/0 bundles:0/0 RX naks:0 defs:0 dups:0 TX naks:0 acks:0 dups:0 Congestion bearer:0 link:0 Send queue max:0 avg:0 Link <10.1.4:ib0-10.1.1:ib0> ACTIVE MTU:2044 Priority:10 Tolerance:1500 ms Window:50 packets RX packets:80 fragments:0/0 bundles:0/0 TX packets:40 fragments:0/0 bundles:0/0 TX profile sample:22 packets average:54 octets 0-64:100% -256:0% -1024:0% -4096:0% -16384:0% -32768:0% -66000:0% RX states:410 probes:213 naks:0 defs:0 dups:0 TX states:410 probes:197 naks:0 acks:0 dups:0 Congestion bearer:0 link:0 Send queue max:1 avg:0 Signed-off-by: Patrick McHardy <kaber@trash.net> Signed-off-by: David S. Miller <davem@davemloft.net>
2013-04-17 14:18:28 +08:00
return 0;
}
tipc: improve and extend media address conversion functions TIPC currently handles two media specific addresses: Ethernet MAC addresses and InfiniBand addresses. Those are kept in three different formats: 1) A "raw" format as obtained from the device. This format is known only by the media specific adapter code in eth_media.c and ib_media.c. 2) A "generic" internal format, in the form of struct tipc_media_addr, which can be referenced and passed around by the generic media- unaware code. 3) A serialized version of the latter, to be conveyed in neighbor discovery messages. Conversion between the three formats can only be done by the media specific code, so we have function pointers for this purpose in struct tipc_media. Here, the media adapters can install their own conversion functions at startup. We now introduce a new such function, 'raw2addr()', whose purpose is to convert from format 1 to format 2 above. We also try to as far as possible uniform commenting, variable names and usage of these functions, with the purpose of making them more comprehensible. We can now also remove the function tipc_l2_media_addr_set(), whose job is done better by the new function. Finally, we expand the field for serialized addresses (format 3) in discovery messages from 20 to 32 bytes. This is permitted according to the spec, and reduces the risk of problems when we add new media in the future. Signed-off-by: Jon Maloy <jon.maloy@ericsson.com> Reviewed-by: Ying Xue <ying.xue@windriver.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-05-14 17:39:13 +08:00
/* Convert from media address format to discovery message addr format */
static int tipc_ib_addr2msg(char *msg, struct tipc_media_addr *addr)
tipc: add InfiniBand media type Add InfiniBand media type based on the ethernet media type. The only real difference is that in case of InfiniBand, we need the entire 20 bytes of space reserved for media addresses, so the TIPC media type ID is not explicitly stored in the packet payload. Sample output of tipc-config: # tipc-config -v -addr -netid -nt=all -p -m -b -n -ls node address: <10.1.4> current network id: 4711 Type Lower Upper Port Identity Publication Scope 0 167776257 167776257 <10.1.1:1855512577> 1855512578 cluster 167776260 167776260 <10.1.4:1216454657> 1216454658 zone 1 1 1 <10.1.4:1216479235> 1216479236 node Ports: 1216479235: bound to {1,1} 1216454657: bound to {0,167776260} Media: eth ib Bearers: ib:ib0 Nodes known: <10.1.1>: up Link <broadcast-link> Window:20 packets RX packets:0 fragments:0/0 bundles:0/0 TX packets:0 fragments:0/0 bundles:0/0 RX naks:0 defs:0 dups:0 TX naks:0 acks:0 dups:0 Congestion bearer:0 link:0 Send queue max:0 avg:0 Link <10.1.4:ib0-10.1.1:ib0> ACTIVE MTU:2044 Priority:10 Tolerance:1500 ms Window:50 packets RX packets:80 fragments:0/0 bundles:0/0 TX packets:40 fragments:0/0 bundles:0/0 TX profile sample:22 packets average:54 octets 0-64:100% -256:0% -1024:0% -4096:0% -16384:0% -32768:0% -66000:0% RX states:410 probes:213 naks:0 defs:0 dups:0 TX states:410 probes:197 naks:0 acks:0 dups:0 Congestion bearer:0 link:0 Send queue max:1 avg:0 Signed-off-by: Patrick McHardy <kaber@trash.net> Signed-off-by: David S. Miller <davem@davemloft.net>
2013-04-17 14:18:28 +08:00
{
memset(msg, 0, TIPC_MEDIA_INFO_SIZE);
tipc: improve and extend media address conversion functions TIPC currently handles two media specific addresses: Ethernet MAC addresses and InfiniBand addresses. Those are kept in three different formats: 1) A "raw" format as obtained from the device. This format is known only by the media specific adapter code in eth_media.c and ib_media.c. 2) A "generic" internal format, in the form of struct tipc_media_addr, which can be referenced and passed around by the generic media- unaware code. 3) A serialized version of the latter, to be conveyed in neighbor discovery messages. Conversion between the three formats can only be done by the media specific code, so we have function pointers for this purpose in struct tipc_media. Here, the media adapters can install their own conversion functions at startup. We now introduce a new such function, 'raw2addr()', whose purpose is to convert from format 1 to format 2 above. We also try to as far as possible uniform commenting, variable names and usage of these functions, with the purpose of making them more comprehensible. We can now also remove the function tipc_l2_media_addr_set(), whose job is done better by the new function. Finally, we expand the field for serialized addresses (format 3) in discovery messages from 20 to 32 bytes. This is permitted according to the spec, and reduces the risk of problems when we add new media in the future. Signed-off-by: Jon Maloy <jon.maloy@ericsson.com> Reviewed-by: Ying Xue <ying.xue@windriver.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-05-14 17:39:13 +08:00
memcpy(msg, addr->value, INFINIBAND_ALEN);
tipc: add InfiniBand media type Add InfiniBand media type based on the ethernet media type. The only real difference is that in case of InfiniBand, we need the entire 20 bytes of space reserved for media addresses, so the TIPC media type ID is not explicitly stored in the packet payload. Sample output of tipc-config: # tipc-config -v -addr -netid -nt=all -p -m -b -n -ls node address: <10.1.4> current network id: 4711 Type Lower Upper Port Identity Publication Scope 0 167776257 167776257 <10.1.1:1855512577> 1855512578 cluster 167776260 167776260 <10.1.4:1216454657> 1216454658 zone 1 1 1 <10.1.4:1216479235> 1216479236 node Ports: 1216479235: bound to {1,1} 1216454657: bound to {0,167776260} Media: eth ib Bearers: ib:ib0 Nodes known: <10.1.1>: up Link <broadcast-link> Window:20 packets RX packets:0 fragments:0/0 bundles:0/0 TX packets:0 fragments:0/0 bundles:0/0 RX naks:0 defs:0 dups:0 TX naks:0 acks:0 dups:0 Congestion bearer:0 link:0 Send queue max:0 avg:0 Link <10.1.4:ib0-10.1.1:ib0> ACTIVE MTU:2044 Priority:10 Tolerance:1500 ms Window:50 packets RX packets:80 fragments:0/0 bundles:0/0 TX packets:40 fragments:0/0 bundles:0/0 TX profile sample:22 packets average:54 octets 0-64:100% -256:0% -1024:0% -4096:0% -16384:0% -32768:0% -66000:0% RX states:410 probes:213 naks:0 defs:0 dups:0 TX states:410 probes:197 naks:0 acks:0 dups:0 Congestion bearer:0 link:0 Send queue max:1 avg:0 Signed-off-by: Patrick McHardy <kaber@trash.net> Signed-off-by: David S. Miller <davem@davemloft.net>
2013-04-17 14:18:28 +08:00
return 0;
}
tipc: improve and extend media address conversion functions TIPC currently handles two media specific addresses: Ethernet MAC addresses and InfiniBand addresses. Those are kept in three different formats: 1) A "raw" format as obtained from the device. This format is known only by the media specific adapter code in eth_media.c and ib_media.c. 2) A "generic" internal format, in the form of struct tipc_media_addr, which can be referenced and passed around by the generic media- unaware code. 3) A serialized version of the latter, to be conveyed in neighbor discovery messages. Conversion between the three formats can only be done by the media specific code, so we have function pointers for this purpose in struct tipc_media. Here, the media adapters can install their own conversion functions at startup. We now introduce a new such function, 'raw2addr()', whose purpose is to convert from format 1 to format 2 above. We also try to as far as possible uniform commenting, variable names and usage of these functions, with the purpose of making them more comprehensible. We can now also remove the function tipc_l2_media_addr_set(), whose job is done better by the new function. Finally, we expand the field for serialized addresses (format 3) in discovery messages from 20 to 32 bytes. This is permitted according to the spec, and reduces the risk of problems when we add new media in the future. Signed-off-by: Jon Maloy <jon.maloy@ericsson.com> Reviewed-by: Ying Xue <ying.xue@windriver.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-05-14 17:39:13 +08:00
/* Convert raw InfiniBand address format to media addr format */
static int tipc_ib_raw2addr(struct tipc_bearer *b,
struct tipc_media_addr *addr,
char *msg)
tipc: add InfiniBand media type Add InfiniBand media type based on the ethernet media type. The only real difference is that in case of InfiniBand, we need the entire 20 bytes of space reserved for media addresses, so the TIPC media type ID is not explicitly stored in the packet payload. Sample output of tipc-config: # tipc-config -v -addr -netid -nt=all -p -m -b -n -ls node address: <10.1.4> current network id: 4711 Type Lower Upper Port Identity Publication Scope 0 167776257 167776257 <10.1.1:1855512577> 1855512578 cluster 167776260 167776260 <10.1.4:1216454657> 1216454658 zone 1 1 1 <10.1.4:1216479235> 1216479236 node Ports: 1216479235: bound to {1,1} 1216454657: bound to {0,167776260} Media: eth ib Bearers: ib:ib0 Nodes known: <10.1.1>: up Link <broadcast-link> Window:20 packets RX packets:0 fragments:0/0 bundles:0/0 TX packets:0 fragments:0/0 bundles:0/0 RX naks:0 defs:0 dups:0 TX naks:0 acks:0 dups:0 Congestion bearer:0 link:0 Send queue max:0 avg:0 Link <10.1.4:ib0-10.1.1:ib0> ACTIVE MTU:2044 Priority:10 Tolerance:1500 ms Window:50 packets RX packets:80 fragments:0/0 bundles:0/0 TX packets:40 fragments:0/0 bundles:0/0 TX profile sample:22 packets average:54 octets 0-64:100% -256:0% -1024:0% -4096:0% -16384:0% -32768:0% -66000:0% RX states:410 probes:213 naks:0 defs:0 dups:0 TX states:410 probes:197 naks:0 acks:0 dups:0 Congestion bearer:0 link:0 Send queue max:1 avg:0 Signed-off-by: Patrick McHardy <kaber@trash.net> Signed-off-by: David S. Miller <davem@davemloft.net>
2013-04-17 14:18:28 +08:00
{
tipc: improve and extend media address conversion functions TIPC currently handles two media specific addresses: Ethernet MAC addresses and InfiniBand addresses. Those are kept in three different formats: 1) A "raw" format as obtained from the device. This format is known only by the media specific adapter code in eth_media.c and ib_media.c. 2) A "generic" internal format, in the form of struct tipc_media_addr, which can be referenced and passed around by the generic media- unaware code. 3) A serialized version of the latter, to be conveyed in neighbor discovery messages. Conversion between the three formats can only be done by the media specific code, so we have function pointers for this purpose in struct tipc_media. Here, the media adapters can install their own conversion functions at startup. We now introduce a new such function, 'raw2addr()', whose purpose is to convert from format 1 to format 2 above. We also try to as far as possible uniform commenting, variable names and usage of these functions, with the purpose of making them more comprehensible. We can now also remove the function tipc_l2_media_addr_set(), whose job is done better by the new function. Finally, we expand the field for serialized addresses (format 3) in discovery messages from 20 to 32 bytes. This is permitted according to the spec, and reduces the risk of problems when we add new media in the future. Signed-off-by: Jon Maloy <jon.maloy@ericsson.com> Reviewed-by: Ying Xue <ying.xue@windriver.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-05-14 17:39:13 +08:00
memset(addr, 0, sizeof(*addr));
memcpy(addr->value, msg, INFINIBAND_ALEN);
addr->media_id = TIPC_MEDIA_TYPE_IB;
addr->broadcast = !memcmp(msg, b->bcast_addr.value,
INFINIBAND_ALEN);
tipc: add InfiniBand media type Add InfiniBand media type based on the ethernet media type. The only real difference is that in case of InfiniBand, we need the entire 20 bytes of space reserved for media addresses, so the TIPC media type ID is not explicitly stored in the packet payload. Sample output of tipc-config: # tipc-config -v -addr -netid -nt=all -p -m -b -n -ls node address: <10.1.4> current network id: 4711 Type Lower Upper Port Identity Publication Scope 0 167776257 167776257 <10.1.1:1855512577> 1855512578 cluster 167776260 167776260 <10.1.4:1216454657> 1216454658 zone 1 1 1 <10.1.4:1216479235> 1216479236 node Ports: 1216479235: bound to {1,1} 1216454657: bound to {0,167776260} Media: eth ib Bearers: ib:ib0 Nodes known: <10.1.1>: up Link <broadcast-link> Window:20 packets RX packets:0 fragments:0/0 bundles:0/0 TX packets:0 fragments:0/0 bundles:0/0 RX naks:0 defs:0 dups:0 TX naks:0 acks:0 dups:0 Congestion bearer:0 link:0 Send queue max:0 avg:0 Link <10.1.4:ib0-10.1.1:ib0> ACTIVE MTU:2044 Priority:10 Tolerance:1500 ms Window:50 packets RX packets:80 fragments:0/0 bundles:0/0 TX packets:40 fragments:0/0 bundles:0/0 TX profile sample:22 packets average:54 octets 0-64:100% -256:0% -1024:0% -4096:0% -16384:0% -32768:0% -66000:0% RX states:410 probes:213 naks:0 defs:0 dups:0 TX states:410 probes:197 naks:0 acks:0 dups:0 Congestion bearer:0 link:0 Send queue max:1 avg:0 Signed-off-by: Patrick McHardy <kaber@trash.net> Signed-off-by: David S. Miller <davem@davemloft.net>
2013-04-17 14:18:28 +08:00
return 0;
}
tipc: improve and extend media address conversion functions TIPC currently handles two media specific addresses: Ethernet MAC addresses and InfiniBand addresses. Those are kept in three different formats: 1) A "raw" format as obtained from the device. This format is known only by the media specific adapter code in eth_media.c and ib_media.c. 2) A "generic" internal format, in the form of struct tipc_media_addr, which can be referenced and passed around by the generic media- unaware code. 3) A serialized version of the latter, to be conveyed in neighbor discovery messages. Conversion between the three formats can only be done by the media specific code, so we have function pointers for this purpose in struct tipc_media. Here, the media adapters can install their own conversion functions at startup. We now introduce a new such function, 'raw2addr()', whose purpose is to convert from format 1 to format 2 above. We also try to as far as possible uniform commenting, variable names and usage of these functions, with the purpose of making them more comprehensible. We can now also remove the function tipc_l2_media_addr_set(), whose job is done better by the new function. Finally, we expand the field for serialized addresses (format 3) in discovery messages from 20 to 32 bytes. This is permitted according to the spec, and reduces the risk of problems when we add new media in the future. Signed-off-by: Jon Maloy <jon.maloy@ericsson.com> Reviewed-by: Ying Xue <ying.xue@windriver.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-05-14 17:39:13 +08:00
/* Convert discovery msg addr format to InfiniBand media addr format */
static int tipc_ib_msg2addr(struct tipc_bearer *b,
struct tipc_media_addr *addr,
char *msg)
{
return tipc_ib_raw2addr(b, addr, msg);
}
/* InfiniBand media registration info */
struct tipc_media ib_media_info = {
.send_msg = tipc_l2_send_msg,
.enable_media = tipc_enable_l2_media,
.disable_media = tipc_disable_l2_media,
.addr2str = tipc_ib_addr2str,
.addr2msg = tipc_ib_addr2msg,
.msg2addr = tipc_ib_msg2addr,
tipc: improve and extend media address conversion functions TIPC currently handles two media specific addresses: Ethernet MAC addresses and InfiniBand addresses. Those are kept in three different formats: 1) A "raw" format as obtained from the device. This format is known only by the media specific adapter code in eth_media.c and ib_media.c. 2) A "generic" internal format, in the form of struct tipc_media_addr, which can be referenced and passed around by the generic media- unaware code. 3) A serialized version of the latter, to be conveyed in neighbor discovery messages. Conversion between the three formats can only be done by the media specific code, so we have function pointers for this purpose in struct tipc_media. Here, the media adapters can install their own conversion functions at startup. We now introduce a new such function, 'raw2addr()', whose purpose is to convert from format 1 to format 2 above. We also try to as far as possible uniform commenting, variable names and usage of these functions, with the purpose of making them more comprehensible. We can now also remove the function tipc_l2_media_addr_set(), whose job is done better by the new function. Finally, we expand the field for serialized addresses (format 3) in discovery messages from 20 to 32 bytes. This is permitted according to the spec, and reduces the risk of problems when we add new media in the future. Signed-off-by: Jon Maloy <jon.maloy@ericsson.com> Reviewed-by: Ying Xue <ying.xue@windriver.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2014-05-14 17:39:13 +08:00
.raw2addr = tipc_ib_raw2addr,
tipc: add InfiniBand media type Add InfiniBand media type based on the ethernet media type. The only real difference is that in case of InfiniBand, we need the entire 20 bytes of space reserved for media addresses, so the TIPC media type ID is not explicitly stored in the packet payload. Sample output of tipc-config: # tipc-config -v -addr -netid -nt=all -p -m -b -n -ls node address: <10.1.4> current network id: 4711 Type Lower Upper Port Identity Publication Scope 0 167776257 167776257 <10.1.1:1855512577> 1855512578 cluster 167776260 167776260 <10.1.4:1216454657> 1216454658 zone 1 1 1 <10.1.4:1216479235> 1216479236 node Ports: 1216479235: bound to {1,1} 1216454657: bound to {0,167776260} Media: eth ib Bearers: ib:ib0 Nodes known: <10.1.1>: up Link <broadcast-link> Window:20 packets RX packets:0 fragments:0/0 bundles:0/0 TX packets:0 fragments:0/0 bundles:0/0 RX naks:0 defs:0 dups:0 TX naks:0 acks:0 dups:0 Congestion bearer:0 link:0 Send queue max:0 avg:0 Link <10.1.4:ib0-10.1.1:ib0> ACTIVE MTU:2044 Priority:10 Tolerance:1500 ms Window:50 packets RX packets:80 fragments:0/0 bundles:0/0 TX packets:40 fragments:0/0 bundles:0/0 TX profile sample:22 packets average:54 octets 0-64:100% -256:0% -1024:0% -4096:0% -16384:0% -32768:0% -66000:0% RX states:410 probes:213 naks:0 defs:0 dups:0 TX states:410 probes:197 naks:0 acks:0 dups:0 Congestion bearer:0 link:0 Send queue max:1 avg:0 Signed-off-by: Patrick McHardy <kaber@trash.net> Signed-off-by: David S. Miller <davem@davemloft.net>
2013-04-17 14:18:28 +08:00
.priority = TIPC_DEF_LINK_PRI,
.tolerance = TIPC_DEF_LINK_TOL,
.window = TIPC_DEF_LINK_WIN,
.type_id = TIPC_MEDIA_TYPE_IB,
.hwaddr_len = INFINIBAND_ALEN,
tipc: add InfiniBand media type Add InfiniBand media type based on the ethernet media type. The only real difference is that in case of InfiniBand, we need the entire 20 bytes of space reserved for media addresses, so the TIPC media type ID is not explicitly stored in the packet payload. Sample output of tipc-config: # tipc-config -v -addr -netid -nt=all -p -m -b -n -ls node address: <10.1.4> current network id: 4711 Type Lower Upper Port Identity Publication Scope 0 167776257 167776257 <10.1.1:1855512577> 1855512578 cluster 167776260 167776260 <10.1.4:1216454657> 1216454658 zone 1 1 1 <10.1.4:1216479235> 1216479236 node Ports: 1216479235: bound to {1,1} 1216454657: bound to {0,167776260} Media: eth ib Bearers: ib:ib0 Nodes known: <10.1.1>: up Link <broadcast-link> Window:20 packets RX packets:0 fragments:0/0 bundles:0/0 TX packets:0 fragments:0/0 bundles:0/0 RX naks:0 defs:0 dups:0 TX naks:0 acks:0 dups:0 Congestion bearer:0 link:0 Send queue max:0 avg:0 Link <10.1.4:ib0-10.1.1:ib0> ACTIVE MTU:2044 Priority:10 Tolerance:1500 ms Window:50 packets RX packets:80 fragments:0/0 bundles:0/0 TX packets:40 fragments:0/0 bundles:0/0 TX profile sample:22 packets average:54 octets 0-64:100% -256:0% -1024:0% -4096:0% -16384:0% -32768:0% -66000:0% RX states:410 probes:213 naks:0 defs:0 dups:0 TX states:410 probes:197 naks:0 acks:0 dups:0 Congestion bearer:0 link:0 Send queue max:1 avg:0 Signed-off-by: Patrick McHardy <kaber@trash.net> Signed-off-by: David S. Miller <davem@davemloft.net>
2013-04-17 14:18:28 +08:00
.name = "ib"
};