OrgACRN
/
acrn-hypervisor
mirror of https://github.com/projectacrn/acrn-hypervisor.git
1
0
Fork 0
Code Issues Releases Wiki Activity
acrn-hypervisor/doc/getting-started/apl-nuc.rst

361 lines
15 KiB
ReStructuredText
Raw Blame History

.. _getting-started-apl-nuc:
Getting started guide for Intel NUC
###################################
The Intel |reg| NUC (NUC6CAYH) is the primary tested
platform for ACRN development, and its setup is described below.
Hardware setup
**************
Two Apollo Lake Intel platforms, described in :ref:`hardware`, are currently
supported for ACRN development:
- The `UP Squared board <http://www.up-board.org/upsquared/>`_ (UP2) is also
known to work and its setup is described in :ref:`getting-started-up2`.
Firmware update on the NUC
==========================
You may need to update to the latest UEFI firmware for the NUC hardware.
Follow these `BIOS Update Instructions
<https://www.intel.com/content/www/us/en/support/articles/000005636.html>`__
for downloading and flashing an updated BIOS for the NUC.
Software setup
**************
Set up a Clear Linux Operating System
=====================================
Currently, an installable version of ARCN does not exist. Therefore, you
need to setup a base Clear Linux OS and you'll build and bootstrap ACRN
on your platform. You'll need a network connection for your platform to
complete this setup.
.. note::
ACRN v0.4 (and the current master branch) requires Clear Linux
version 26770 or newer. If you use a newer version of Clear Linux,
you'll need to adjust the instructions below to reference the version
number of Clear Linux you are using.
#. Download the compressed Clear installer image from
https://download.clearlinux.org/releases/26770/clear/clear-26770-installer.img.xz
and follow the `Clear Linux installation guide
<https://clearlinux.org/documentation/clear-linux/get-started/bare-metal-install>`__
as a starting point for installing Clear Linux onto your platform. Follow the recommended
options for choosing an **Manual (Advanced)** installation type, and using the platform's
storage as the target device for installation (overwriting the existing data
and creating three partitions on the platform's storage drive).
High-level steps should be:
#. Install Clear on a NUC using the "Manual (Advanced)" option.
#. Use default partition scheme for storage
#. Name the host "clr-sos-guest"
#. Add an administrative user "clear" with "sudoers" privilege
#. Add these additional bundles "editors", "user-basic", "desktop-autostart", "network-basic"
#. For network, choose “DHCP”
#. After installation is complete, boot into Clear Linux, login as
**clear**, and set a password.
#. Clear Linux is set to automatically update itself. We recommend that you disable
this feature to have more control over when the updates happen. Use this command
to disable the autoupdate feature:
.. code-block:: none
$ sudo swupd autoupdate --disable
.. note::
The Clear Linux installer will automatically check for updates and install the
latest version available on your system. If you wish to use a specific version
(such as 26770), you can achieve that after the installation has completed using
``sudo swupd verify --fix --picky -m 26770``
#. If you have an older version of Clear Linux already installed
on your hardware, use this command to upgrade Clear Linux
to version 26770 (or newer):
.. code-block:: none
$ sudo swupd update -m 26770 # or newer version
#. Use the ``sudo swupd bundle-add`` command and add these Clear Linux bundles:
.. code-block:: none
$ sudo swupd bundle-add service-os kernel-iot-lts2018
.. table:: Clear Linux bundles
:widths: auto
:name: CL-bundles
+--------------------+---------------------------------------------------+
| Bundle | Description |
+====================+===================================================+
| service-os | Add the acrn hypervisor, the acrn devicemodel and |
| | Service OS kernel |
+--------------------+---------------------------------------------------+
| kernel-iot-lts2018 | Run the Intel kernel"kernel-iot-lts2018" |
| | which is enterprise-style kernel with backports |
+--------------------+---------------------------------------------------+
Add the ACRN hypervisor to the EFI Partition
============================================
In order to boot the ACRN SOS on the platform, you'll need to add it to the EFI
partition. Follow these steps:
#. Mount the EFI partition and verify you have the following files:
.. code-block:: none
$ sudo ls -1 /boot/EFI/org.clearlinux
bootloaderx64.efi
kernel-org.clearlinux.native.4.19.8-670
kernel-org.clearlinux.iot-lts2018-sos.4.19.5-29
kernel-org.clearlinux.iot-lts2018.4.19.5-29
kernel-org.clearlinux.pk414-sos.4.14.74-115
loaderx64.efi
.. note::
On Clear Linux, the EFI System Partion (e.g.: ``/dev/sda1``) is mounted under ``/boot`` by default
The Clear Linux project releases updates often, sometimes
twice a day, so make note of the specific kernel versions (*iot-lts2018 and *iot-lts2018-sos*) listed on your system,
as you will need them later.
.. note::
The EFI System Partition (ESP) may be different based on your hardware.
It will typically be something like ``/dev/mmcblk0p1`` on platforms
that have an on-board eMMC or ``/dev/nvme0n1p1`` if your system has
a non-volatile storage media attached via a PCI Express (PCIe) bus
(NVMe).
#. Put the ``acrn.efi`` hypervisor application (included in the Clear
Linux release) on the EFI partition with:
.. code-block:: none
$ sudo mkdir /boot/EFI/acrn
$ sudo cp /usr/lib/acrn/acrn.efi /boot/EFI/acrn/
#. Configure the EFI firmware to boot the ACRN hypervisor by default
The ACRN hypervisor (``acrn.efi``) is an EFI executable
loaded directly by the platform EFI firmware. It then in turns loads the
Service OS bootloader. Use the ``efibootmgr`` utility to configure the EFI
firmware and add a new entry that loads the ACRN hypervisor.
.. code-block:: none
$ sudo efibootmgr -c -l "\EFI\acrn\acrn.efi" -d /dev/sda -p 1 -L "ACRN"
.. note::
Be aware that a Clearlinux update that includes a kernel upgrade will
reset the boot option changes you just made. A Clearlinux update could
happen automatically (if you have not disabled it as described above),
if you later install a new bundle to your system, or simply if you
decide to trigger an update manually. Whenever that happens,
double-check the platform boot order using ``efibootmgr -v`` and
modify it if needed.
The ACRN hypervisor (``acrn.efi``) accepts three command-line parameters that
tweak its behaviour:
1. ``bootloader=``: this sets the EFI executable to be loaded once the hypervisor
is up and running. This is typically the bootloader of the Service OS and the
default value is to use the Clearlinux bootloader, i.e.:
``\EFI\org.clearlinux\bootloaderx64.efi``.
#. ``uart=``: this tells the hypervisor where the serial port (UART) is found or
whether it should be disabled. There are three forms for this parameter:
#. ``uart=disabled``: this disables the serial port completely
#. ``uart=bdf@<BDF value>``: this sets the PCI serial port based on its BDF.
For example, use ``bdf@0:18.1`` for a BDF of 0:18.1 ttyS1.
#. ``uart=port@<port address>``: this sets the serial port address
#. ``vuart=ttySn@irqN``: this tells the hypervisor which virtual serial device SOS
will use and its IRQ number. This is used to avoid conflict with SOS passthrough
devices' interrupt. If UART is set to ttyS1, and its native IRQ is 5, you'd better
set ``vuart=ttyS1@irq5`` (Use 'dmesg | grep tty' to get IRQ information).
Also set ``console=ttyS1`` in ``acrn.conf`` to match the SOS boot args.
Here is a more complete example of how to configure the EFI firmware to load the ACRN
hypervisor and set these parameters.
.. code-block:: none
$ sudo efibootmgr -c -l "\EFI\acrn\acrn.efi" -d /dev/sda -p 1 -L "ACRN NUC Hypervisor" \
-u "bootloader=\EFI\org.clearlinux\bootloaderx64.efi uart=disabled"
#. Create a boot entry for the ACRN Service OS by copying a provided ``acrn.conf``
and editing it to account for the kernel versions noted in a previous step.
It must contain these settings:
+-----------+----------------------------------------------------------------+
| Setting | Description |
+===========+================================================================+
| title | Text to show in the boot menu |
+-----------+----------------------------------------------------------------+
| linux | Linux kernel for the Service OS (\*-sos) |
+-----------+----------------------------------------------------------------+
| options | Options to pass to the Service OS kernel (kernel parameters) |
+-----------+----------------------------------------------------------------+
A starter acrn.conf configuration file is included in the Clear Linux release and is
also available in the acrn-hypervisor/hypervisor GitHub repo as `acrn.conf
<https://github.com/projectacrn/acrn-hypervisor/blob/master/efi-stub/clearlinux/acrn.conf>`__
as shown here:
.. literalinclude:: ../../efi-stub/clearlinux/acrn.conf
:caption: efi-stub/clearlinux/acrn.conf
On the platform, copy the ``acrn.conf`` file to the EFI partition we mounted earlier:
.. code-block:: none
$ sudo cp /usr/share/acrn/samples/nuc/acrn.conf /boot/loader/entries/
You will need to edit this file to adjust the kernel version (``linux`` section),
insert the ``PARTUUID`` of your ``/dev/sda3`` partition
(``root=PARTUUID=<UUID of rootfs partition>``) in the ``options`` section, and
add the ``hugepagesz=1G hugepages=2`` at end of the ``options`` section.
Use ``blkid`` to find out what your ``/dev/sda3`` ``PARTUUID`` value is.
.. note::
It is also possible to use the device name directly, e.g. ``root=/dev/sda3``
#. Add a timeout period for Systemd-Boot to wait, otherwise it will not
present the boot menu and will always boot the base Clear Linux
.. code-block:: none
$ sudo clr-boot-manager set-timeout 20
$ sudo clr-boot-manager update
#. Reboot and select "The ACRN Service OS" to boot, as shown below:
.. code-block:: console
:emphasize-lines: 1
:caption: ACRN Service OS Boot Menu
=> The ACRN Service OS
Clear Linux OS for Intel Architecture (Clear-linux-iot-lts2018-4.19.5-29)
Clear Linux OS for Intel Architecture (Clear-linux-iot-lts2018-sos-4.19.5-29)
Clear Linux OS for Intel Architecture (Clear-linux-native.4.19.8-670)
EFI Default Loader
Reboot Into Firmware Interface
#. After booting up the ACRN hypervisor, the Service OS will be launched
automatically by default, and the Clear Linux desktop will be showing with user "clear",
(or you can login remotely with an "ssh" client).
If there is any issue which makes the GNOME desktop doesn't show successfully, then the system will go to
shell console.
#. From ssh client, login as user "clear" using the password you set previously when
you installed Clear Linux.
#. After rebooting the system, check that the ACRN hypervisor is running properly with:
.. code-block:: none
$ dmesg | grep ACRN
[ 0.000000] Hypervisor detected: ACRN
[ 1.687128] ACRNTrace: acrn_trace_init, cpu_num 4
[ 1.693129] ACRN HVLog: acrn_hvlog_init
If you see log information similar to this, the ACRN hypervisor is running properly
and you can start deploying a User OS. If not, verify the EFI boot options, SOS
kernel, and ``acrn.conf`` settings are correct (as described above).
ACRN Network Bridge
===================
ACRN bridge has been setup as a part of systemd services for device communication. The default
bridge creates ``acrn_br0`` which is the bridge and ``acrn_tap0`` as an initial setup. The files can be
found in ``/usr/lib/systemd/network``. No additional setup is needed since systemd-networkd is
automatically enabled after a system restart.
Set up Reference UOS
====================
#. On your platform, download the pre-built reference Clear Linux UOS
image version 26770 (or newer) into your (root) home directory:
.. code-block:: none
$ cd ~
$ mkdir uos
$ cd uos
$ curl -O https://download.clearlinux.org/releases/26770/clear/clear-26770-kvm.img.xz
.. note::
In case you want to use or try out a newer version of Clear Linux as the UOS, you can
download the latest from http://download.clearlinux.org/image. Make sure to adjust the steps
described below accordingly (image file name and kernel modules version).
#. Uncompress it:
.. code-block:: none
$ unxz clear-26770-kvm.img.xz
#. Deploy the UOS kernel modules to UOS virtual disk image (note: you'll need to use
the same **iot-lts2018** image version number noted in step 1 above):
.. code-block:: none
$ sudo losetup -f -P --show clear-26770-kvm.img
$ sudo mount /dev/loop0p3 /mnt
$ sudo cp -r /usr/lib/modules/4.19.5-29.iot-lts2018 /mnt/lib/modules/
$ sudo umount /mnt
$ sync
#. Edit and Run the ``launch_uos.sh`` script to launch the UOS.
A sample `launch_uos.sh
<https://raw.githubusercontent.com/projectacrn/acrn-hypervisor/master/devicemodel/samples/nuc/launch_uos.sh>`__
is included in the Clear Linux release, and
is also available in the acrn-hypervisor/devicemodel GitHub repo (in the samples
folder) as shown here:
.. literalinclude:: ../../devicemodel/samples/nuc/launch_uos.sh
:caption: devicemodel/samples/nuc/launch_uos.sh
:language: bash
:emphasize-lines: 23,25
.. note::
In case you have downloaded a different Clear Linux image than the one above
(``clear-26770-kvm.img.xz``), you will need to modify the Clear Linux file name
and version number highlighted above (the ``-s 3,virtio-blk`` argument) to match
what you have downloaded above. Likewise, you may need to adjust the kernel file
name on the second line highlighted (check the exact name to be used using:
``ls /usr/lib/kernel/org.clearlinux.iot-lts2018*``).
By default, the script is located in the ``/usr/share/acrn/samples/nuc/``
directory. You can edit it there, and then run it to launch the User OS:
.. code-block:: none
$ cd /usr/share/acrn/samples/nuc/
$ sudo ./launch_uos.sh
#. At this point, you've successfully booted the ACRN hypervisor,
SOS, and UOS:
.. figure:: images/gsg-successful-boot.png
:align: center
:name: gsg-successful-boot
Reference in New Issue View Git Blame Copy Permalink