100 lines
3.5 KiB
ReStructuredText
100 lines
3.5 KiB
ReStructuredText
.. _virtio-input:
|
|
|
|
Virtio-Input
|
|
############
|
|
|
|
The virtio input device can be used to create virtual human interface
|
|
devices such as keyboards, mice, and tablets. It basically sends Linux
|
|
input layer events over virtio.
|
|
|
|
The ACRN Virtio-input architecture is shown below.
|
|
|
|
.. figure:: images/virtio-hld-image53.png
|
|
:align: center
|
|
|
|
Virtio-input Architecture on ACRN
|
|
|
|
Virtio-input is implemented as a virtio modern device in ACRN device
|
|
model. It is registered as a PCI virtio device to guest OS. No changes
|
|
are required in frontend Linux virtio-input except that guest kernel
|
|
must be built with ``CONFIG_VIRTIO_INPUT=y``.
|
|
|
|
Two virtqueues are used to transfer input_event between FE and BE. One
|
|
is for the input_events from BE to FE, as generated by input hardware
|
|
devices in Service VM. The other is for status changes from FE to BE, as
|
|
finally sent to input hardware device in Service VM.
|
|
|
|
At the probe stage of FE virtio-input driver, a buffer (used to
|
|
accommodate 64 input events) is allocated together with the driver data.
|
|
Sixty-four descriptors are added to the event virtqueue. One descriptor
|
|
points to one entry in the buffer. Then a kick on the event virtqueue is
|
|
performed.
|
|
|
|
Virtio-input BE driver in device model uses mevent to poll the
|
|
availability of the input events from an input device thru evdev char
|
|
device. When an input event is available, BE driver reads it out from the
|
|
char device and caches it into an internal buffer until an EV_SYN input
|
|
event with SYN_REPORT is received. BE driver then copies all the cached
|
|
input events to the event virtqueue, one by one. These events are added by
|
|
the FE driver following a notification to FE driver, implemented
|
|
as an interrupt injection to User VM.
|
|
|
|
For input events regarding status change, FE driver allocates a
|
|
buffer for an input event and adds it to the status virtqueue followed
|
|
by a kick. BE driver reads the input event from the status virtqueue and
|
|
writes it to the evdev char device.
|
|
|
|
The data transferred between FE and BE is organized as struct
|
|
input_event:
|
|
|
|
.. code-block:: c
|
|
|
|
struct input_event {
|
|
struct timeval time;
|
|
__u16 type;
|
|
__u16 code;
|
|
__s32 value;
|
|
};
|
|
|
|
A structure virtio_input_config is defined and used as the
|
|
device-specific configuration registers. To query a specific piece of
|
|
configuration information FE driver sets "select" and "subsel"
|
|
accordingly. Information size is returned in "size" and information data
|
|
is returned in union "u":
|
|
|
|
.. code-block:: c
|
|
|
|
struct virtio_input_config {
|
|
uint8_t select;
|
|
uint8_t subsel;
|
|
uint8_t size;
|
|
uint8_t reserved[5];
|
|
union {
|
|
char string[128];
|
|
uint8_t bitmap[128];
|
|
struct virtio_input_absinfo abs;
|
|
struct virtio_input_devids ids;
|
|
} u;
|
|
};
|
|
|
|
Read/Write to these registers results in a vmexit and cfgread/cfgwrite
|
|
callbacks in struct virtio_ops are called finally in device model.
|
|
Virtio-input BE in device model issues ioctl to evdev char device
|
|
according to the "select" and "subselect" registers to get the
|
|
corresponding device capabilities information from kernel and return
|
|
these information to guest OS.
|
|
|
|
All the device-specific configurations are obtained by FE driver at
|
|
probe stage. Based on these information virtio-input FE driver registers
|
|
an input device to the input subsystem.
|
|
|
|
The general command syntax is::
|
|
|
|
-s n,virtio-input,/dev/input/eventX[,serial]
|
|
|
|
- /dev/input/eventX is used to specify the evdev char device node in
|
|
Service VM.
|
|
|
|
- "serial" is an optional string. When it is specified it will be used
|
|
as the Uniq of guest virtio input device.
|