acrn-hypervisor/Makefile

260 lines
9.9 KiB
Makefile

# acrn-hypervisor/Makefile
# global helper variables
T := $(CURDIR)
TARGET_DIR ?=
# BOARD/SCENARIO/BOARD_FILE/SCENARIO_FILE/KCONFIG_FILE parameters sanity check:
#
# Only below usages are VALID: (target = all | hypervisor)
# 1. make <target>
# 2. make <target> KCONFIG_FILE=xxx [TARGET_DIR=xxx]
# 3. make <target> BOARD=xxx SCENARIO=xxx [TARGET_DIR=xxx]
# 4. make <target> BOARD_FILE=xxx SCENARIO_FILE=xxx [TARGET_DIR=xxx]
#
# Especially for case 1 that no any parameters are specified:
# a. If hypervisor/build/.config file which generated by "make menuconfig" exist,
# the .config file will be loaded as KCONFIG_FILE:
# i.e. equal: make <target> KCONFIG_FILE=hypervisor/build/.config
#
# b. If hypervisor/build/.config file does not exist,
# the default BOARD/SCENARIO will be loaded:
# i.e. equal: make <target> BOARD=$(BOARD) SCENARIO=$(SCENARIO)
#
# For case 2/3, configurations are imported from TARGET_DIR when TARGET_DIR is specified;
# For case 4, configurations are from XML files and saved to TARGET_DIR if it is specified;
#
# The grep process did not handle corner case when '#' is manually put right after config value as comments,
# i.e. it will be failed in the case of "CONFIG_XXX=y # some comments here "
ifneq ($(KCONFIG_FILE),)
ifneq ($(KCONFIG_FILE), $(wildcard $(KCONFIG_FILE)))
$(error KCONFIG_FILE: $(KCONFIG_FILE) does not exist)
endif
override KCONFIG_FILE := $(realpath $(KCONFIG_FILE))
else
override KCONFIG_FILE := $(T)/hypervisor/build/.config
endif
ifneq ($(BOARD)$(SCENARIO),)
ifneq ($(BOARD_FILE)$(SCENARIO_FILE),)
$(error BOARD/SCENARIO parameter could not coexist with BOARD_FILE/SCENARIO_FILE)
endif
endif
ifneq ($(TARGET_DIR),)
CFG_DIR := $(realpath $(TARGET_DIR))
ifeq ($(CFG_DIR),)
ifeq ($(BOARD_FILE)$(SCENARIO_FILE),)
$(error TARGET_DIR $(TARGET_DIR) does not exist)
endif
endif
override TARGET_DIR := $(abspath $(TARGET_DIR))
endif
ifneq ($(BOARD_FILE)$(SCENARIO_FILE),)
ifneq ($(BOARD_FILE), $(wildcard $(BOARD_FILE)))
$(error BOARD_FILE: $(BOARD_FILE) does not exist)
endif
ifneq ($(SCENARIO_FILE), $(wildcard $(SCENARIO_FILE)))
$(error SCENARIO_FILE: $(SCENARIO_FILE) does not exist)
endif
override BOARD_FILE := $(realpath $(BOARD_FILE))
override SCENARIO_FILE := $(realpath $(SCENARIO_FILE))
endif
ifeq ($(KCONFIG_FILE), $(wildcard $(KCONFIG_FILE)))
ifneq ($(BOARD)$(SCENARIO),)
$(error BOARD/SCENARIO parameter could not coexist with Kconfig file: $(KCONFIG_FILE))
endif
ifneq ($(BOARD_FILE)$(SCENARIO_FILE),)
$(error BOARD_FILE/SCENARIO_FILE parameter could not coexist with Kconfig file: $(KCONFIG_FILE))
endif
BOARD_IN_KCONFIG := $(shell grep CONFIG_BOARD= $(KCONFIG_FILE) | grep -v '\#' | awk -F '"' '{print $$2}')
ifeq ($(BOARD_IN_KCONFIG),)
$(error no BOARD info in KCONFIG_FILE: $(KCONFIG_FILE))
endif
SCENARIO_IN_KCONFIG := $(shell grep CONFIG_SCENARIO= $(KCONFIG_FILE) | grep -v '\#' | awk -F '"' '{print $$2}')
ifeq ($(SCENARIO_IN_KCONFIG),)
$(error no SCENARIO info in KCONFIG_FILE: $(KCONFIG_FILE))
endif
override BOARD := $(BOARD_IN_KCONFIG)
override SCENARIO := $(SCENARIO_IN_KCONFIG)
RELEASE := $(shell grep CONFIG_RELEASE=y $(KCONFIG_FILE) | grep -v '\#')
ifneq ($(RELEASE),)
override RELEASE := 1
endif
endif
BOARD ?= kbl-nuc-i7
ifeq ($(BOARD), apl-nuc)
override BOARD := nuc6cayh
else ifeq ($(BOARD), kbl-nuc-i7)
override BOARD := nuc7i7dnb
endif
ifneq (,$(filter $(BOARD),apl-mrb))
FIRMWARE ?= sbl
else
FIRMWARE ?= uefi
endif
SCENARIO ?= industry
O ?= build
ROOT_OUT := $(shell mkdir -p $(O);cd $(O);pwd)
HV_OUT := $(ROOT_OUT)/hypervisor
EFI_OUT := misc/efi-stub
DM_OUT := $(ROOT_OUT)/devicemodel
TOOLS_OUT := $(ROOT_OUT)/misc/tools
DOC_OUT := $(ROOT_OUT)/doc
BUILD_VERSION ?=
BUILD_TAG ?=
HV_CFG_LOG = $(HV_OUT)/cfg.log
VM_CONFIGS_DIR = $(T)/misc/vm_configs
DEFCONFIG_FILE = scenarios/$(SCENARIO)/$(BOARD)/$(BOARD).config
export TOOLS_OUT BOARD SCENARIO FIRMWARE RELEASE
.PHONY: all hypervisor devicemodel tools doc
all: hypervisor devicemodel tools
@cat $(HV_CFG_LOG)
include $(T)/hypervisor/scripts/makefile/cfg_update.mk
#help functions to build acrn and install acrn/acrn symbols
define build_acrn
$(MAKE) -C $(T)/hypervisor HV_OBJDIR=$(HV_OUT)-$(1)/$(2) BOARD=$(2) FIRMWARE=$(1) SCENARIO=$(3) RELEASE=$(RELEASE) clean
$(MAKE) -C $(T)/hypervisor HV_OBJDIR=$(HV_OUT)-$(1)/$(2) BOARD=$(2) FIRMWARE=$(1) SCENARIO=$(3) RELEASE=$(RELEASE) defconfig
$(MAKE) -C $(T)/hypervisor HV_OBJDIR=$(HV_OUT)-$(1)/$(2) BOARD=$(2) FIRMWARE=$(1) SCENARIO=$(3) RELEASE=$(RELEASE) oldconfig
$(MAKE) -C $(T)/hypervisor HV_OBJDIR=$(HV_OUT)-$(1)/$(2) BOARD=$(2) FIRMWARE=$(1) SCENARIO=$(3) RELEASE=$(RELEASE)
echo "building hypervisor as EFI executable..."
@if [ "$(1)" = "uefi" ]; then \
$(MAKE) -C $(T)/misc/efi-stub HV_OBJDIR=$(HV_OUT)-$(1)/$(2) SCENARIO=$(3) EFI_OBJDIR=$(HV_OUT)-$(1)/$(2)/$(EFI_OUT); \
fi
endef
define install_acrn
$(MAKE) -C $(T)/hypervisor HV_OBJDIR=$(HV_OUT)-$(1)/$(2) BOARD=$(2) FIRMWARE=$(1) SCENARIO=$(3) RELEASE=$(RELEASE) install
@if [ "$(1)" = "uefi" ]; then \
$(MAKE) -C $(T)/misc/efi-stub HV_OBJDIR=$(HV_OUT)-$(1)/$(2) BOARD=$(2) FIRMWARE=$(1) SCENARIO=$(3) RELEASE=$(RELEASE) EFI_OBJDIR=$(HV_OUT)-$(1)/$(2)/$(EFI_OUT) install; \
fi
endef
define install_acrn_debug
$(MAKE) -C $(T)/hypervisor HV_OBJDIR=$(HV_OUT)-$(1)/$(2) BOARD=$(2) FIRMWARE=$(1) SCENARIO=$(3) RELEASE=$(RELEASE) install-debug
@if [ "$(1)" = "uefi" ]; then \
$(MAKE) -C $(T)/misc/efi-stub HV_OBJDIR=$(HV_OUT)-$(1)/$(2) BOARD=$(2) FIRMWARE=$(1) SCENARIO=$(3) RELEASE=$(RELEASE) EFI_OBJDIR=$(HV_OUT)-$(1)/$(2)/$(EFI_OUT) install-debug; \
fi
endef
hypervisor:
@if [ "$(BOARD_FILE)" != "" ] && [ -f $(BOARD_FILE) ] && [ "$(SCENARIO_FILE)" != "" ] && [ -f $(SCENARIO_FILE) ] && [ "$(TARGET_DIR)" = "" ]; then \
echo "No TARGET_DIR parameter is specified, the original configuration source is overwritten!";\
fi
$(MAKE) -C $(T)/hypervisor BOARD=$(BOARD) HV_OBJDIR=$(HV_OUT) BOARD_FILE=$(BOARD_FILE) SCENARIO_FILE=$(SCENARIO_FILE) TARGET_DIR=$(TARGET_DIR) defconfig;
$(MAKE) -C $(T)/hypervisor BOARD=$(BOARD) HV_OBJDIR=$(HV_OUT) BOARD_FILE=$(BOARD_FILE) SCENARIO_FILE=$(SCENARIO_FILE) TARGET_DIR=$(TARGET_DIR) oldconfig;
$(MAKE) -C $(T)/hypervisor BOARD=$(BOARD) HV_OBJDIR=$(HV_OUT) BOARD_FILE=$(BOARD_FILE) SCENARIO_FILE=$(SCENARIO_FILE) TARGET_DIR=$(TARGET_DIR)
#ifeq ($(FIRMWARE),uefi)
@if [ "$(SCENARIO)" != "logical_partition" ] && [ "$(SCENARIO)" != "hybrid" ]; then \
echo "building hypervisor as EFI executable..."; \
$(MAKE) -C $(T)/misc/efi-stub HV_OBJDIR=$(HV_OUT) EFI_OBJDIR=$(HV_OUT)/$(EFI_OUT); \
fi
#endif
@echo -e "\n\033[47;30mACRN Configuration Summary:\033[0m \nBOARD = $(BOARD)\t SCENARIO = $(SCENARIO)" > $(HV_CFG_LOG); \
echo -e "BUILD type = \c" >> $(HV_CFG_LOG); \
if [ "$(RELEASE)" = "0" ]; then echo -e "DEBUG" >> $(HV_CFG_LOG); else echo -e "RELEASE" >> $(HV_CFG_LOG); fi; \
if [ -f $(KCONFIG_FILE) ]; then \
echo -e "Hypervisor configuration is based on:\n\tKconfig file:\t$(KCONFIG_FILE);" >> $(HV_CFG_LOG); \
fi; \
echo -e "Hypervisor configuration is based on:" >> $(HV_CFG_LOG); \
if [ "$(TARGET_DIR)" = "" ]; then \
if [ ! -f $(KCONFIG_FILE) ]; then \
echo -e "\tdefconfig file:\t\t\t$(VM_CONFIGS_DIR)/$(DEFCONFIG_FILE);" >> $(HV_CFG_LOG); \
fi; \
elif [ ! -f $(KCONFIG_FILE) ]; then \
echo -e "\tdefconfig file:\t\t\t$(TARGET_DIR)/$(DEFCONFIG_FILE);" >> $(HV_CFG_LOG); \
fi; \
echo -e "\tOthers are set by default in:\t$(T)/hypervisor/arch/x86/Kconfig;" >> $(HV_CFG_LOG); \
echo -e "VM configuration is based on:" >> $(HV_CFG_LOG); \
if [ "$(CONFIG_XML_ENABLED)" = "true" ]; then \
echo -e "\tBOARD File:\t\t$(BOARD_FILE);\n\t\tSCENARIO File:\t$(SCENARIO_FILE);" >> $(HV_CFG_LOG); \
elif [ "$(TARGET_DIR)" = "" ]; then \
echo -e "\tSource code at:\t\t\t$(VM_CONFIGS_DIR)" >> $(HV_CFG_LOG); \
else \
echo -e "\tSource code at:\t\t\t$(TARGET_DIR)" >> $(HV_CFG_LOG); \
fi;
@cat $(HV_CFG_LOG)
devicemodel: tools
$(MAKE) -C $(T)/devicemodel DM_OBJDIR=$(DM_OUT) DM_BUILD_VERSION=$(BUILD_VERSION) DM_BUILD_TAG=$(BUILD_TAG) DM_ASL_COMPILER=$(ASL_COMPILER) RELEASE=$(RELEASE)
tools:
mkdir -p $(TOOLS_OUT)
$(MAKE) -C $(T)/misc OUT_DIR=$(TOOLS_OUT) RELEASE=$(RELEASE)
doc:
$(MAKE) -C $(T)/doc html BUILDDIR=$(DOC_OUT)
.PHONY: clean
clean:
$(MAKE) -C $(T)/misc OUT_DIR=$(TOOLS_OUT) clean
$(MAKE) -C $(T)/doc BUILDDIR=$(DOC_OUT) clean
rm -rf $(ROOT_OUT)
rm -rf $(TARGET_DIR)
.PHONY: install
install: hypervisor-install devicemodel-install tools-install
hypervisor-install:
$(MAKE) -C $(T)/hypervisor HV_OBJDIR=$(HV_OUT) BOARD=$(BOARD) FIRMWARE=$(FIRMWARE) SCENARIO=$(SCENARIO) RELEASE=$(RELEASE) install
ifeq ($(FIRMWARE),uefi)
$(MAKE) -C $(T)/misc/efi-stub HV_OBJDIR=$(HV_OUT) BOARD=$(BOARD) FIRMWARE=$(FIRMWARE) SCENARIO=$(SCENARIO) EFI_OBJDIR=$(HV_OUT)/$(EFI_OUT) all install
endif
hypervisor-install-debug:
$(MAKE) -C $(T)/hypervisor HV_OBJDIR=$(HV_OUT) BOARD=$(BOARD) FIRMWARE=$(FIRMWARE) SCENARIO=$(SCENARIO) RELEASE=$(RELEASE) install-debug
ifeq ($(FIRMWARE),uefi)
$(MAKE) -C $(T)/misc/efi-stub HV_OBJDIR=$(HV_OUT) BOARD=$(BOARD) FIRMWARE=$(FIRMWARE) SCENARIO=$(SCENARIO) EFI_OBJDIR=$(HV_OUT)/$(EFI_OUT) all install-debug
endif
kbl-nuc-i7-uefi-industry:
$(call build_acrn,uefi,nuc7i7dnb,industry)
apl-up2-uefi-hybrid:
$(call build_acrn,uefi,apl-up2,hybrid)
sbl-hypervisor: kbl-nuc-i7-uefi-industry \
apl-up2-uefi-hybrid
kbl-nuc-i7-uefi-industry-install:
$(call install_acrn,uefi,nuc7i7dnb,industry)
apl-up2-uefi-hybrid-install:
$(call install_acrn,uefi,apl-up2,hybrid)
sbl-hypervisor-install: kbl-nuc-i7-uefi-industry-install \
apl-up2-uefi-hybrid-install
kbl-nuc-i7-uefi-industry-install-debug:
$(call install_acrn_debug,uefi,nuc7i7dnb,industry)
apl-up2-uefi-hybrid-install-debug:
$(call install_acrn_debug,uefi,apl-up2,hybrid)
sbl-hypervisor-install-debug: kbl-nuc-i7-uefi-industry-install-debug \
apl-up2-uefi-hybrid-install-debug
devicemodel-install:
$(MAKE) -C $(T)/devicemodel DM_OBJDIR=$(DM_OUT) install
tools-install:
$(MAKE) -C $(T)/misc OUT_DIR=$(TOOLS_OUT) RELEASE=$(RELEASE) install