122 lines
4.2 KiB
ReStructuredText
122 lines
4.2 KiB
ReStructuredText
.. _getting-started-up2:
|
|
|
|
Getting started guide for UP2 board
|
|
###################################
|
|
|
|
Hardware setup
|
|
**************
|
|
|
|
The `UP Squared board <http://www.up-board.org/upsquared/specifications/>`_ (UP2) is
|
|
an x86 maker board based on the Intel Apollo Lake platform. The UP boards
|
|
are used in IoT applications, industrial automation, digital signage, and more.
|
|
|
|
The UP2 features Intel `Celeron N3550
|
|
<https://ark.intel.com/products/95598/Intel-Celeron-Processor-N3350-2M-Cache-up-to-2_4-GHz>`_
|
|
and Intel `Pentium N4200
|
|
<https://ark.intel.com/products/95592/Intel-Pentium-Processor-N4200-2M-Cache-up-to-2_5-GHz>`_
|
|
SoCs. Both have been confirmed to work with ACRN.
|
|
|
|
Connecting to the serial port
|
|
=============================
|
|
|
|
The UP2 board has two serial ports. The following figure shows the UP2 board's
|
|
40-pin HAT connector we'll be using as documented in the `UP2 Datasheet
|
|
<https://up-board.org/wp-content/uploads/datasheets/UP-Square-DatasheetV0.5.pdf>`_.
|
|
|
|
.. image:: images/the-bottom-side-of-UP2-board.png
|
|
:align: center
|
|
|
|
We'll access the serial port through the I/O pins in the
|
|
40-pin HAT connector using a `USB TTL serial cable
|
|
<http://www.ftdichip.com/Products/USBTTLSerial.htm>`_,
|
|
and show how to connect a serial port with
|
|
``PL2303TA USB to TTL serial cable`` for example:
|
|
|
|
.. image:: images/USB-to-TTL-serial-cable.png
|
|
:align: center
|
|
|
|
Connect pin 6 (``Ground``), pin 8 (``UART_TXD``) and pin 10 (``UART_RXD``) of the HAT
|
|
connector to respectively the ``GND``, ``RX`` and ``TX`` pins of your
|
|
USB serial cable. Plug the USB TTL serial cable into your PC and use a
|
|
console emulation tool such as ``minicom`` or ``putty`` to communicate
|
|
with the UP2 board for debugging.
|
|
|
|
.. image:: images/the-connection-of-serial-port.png
|
|
:align: center
|
|
|
|
Software setup
|
|
**************
|
|
|
|
Setting up the ACRN hypervisor (and associated components) on the UP2
|
|
board is no different than other hardware platforms so please follow
|
|
the instructions provided in the :ref:`rt_industry_setup`, with
|
|
the additional information below.
|
|
|
|
There are a few parameters specific to the UP2 board that differ from
|
|
what is referenced in the :ref:`rt_industry_setup` section:
|
|
|
|
1. Serial Port settings
|
|
#. Storage device name
|
|
|
|
You will need to keep these in mind in a few places:
|
|
|
|
* When mounting the EFI System Partition (ESP)
|
|
|
|
.. code-block:: none
|
|
|
|
# mount /dev/mmcblk0p1 /mnt
|
|
|
|
* When adjusting the ``acrn.conf`` file
|
|
|
|
* Set the ``root=`` parameter using the ``PARTUUID`` or device name directly
|
|
|
|
* When configuring the EFI firmware to boot the ACRN hypervisor by default
|
|
|
|
.. code-block:: none
|
|
|
|
# efibootmgr -c -l "\EFI\acrn\acrn.efi" -d /dev/mmcblk0 -p 1 -L "ACRN Hypervisor" \
|
|
-u "bootloader=\EFI\org.clearlinux\bootloaderx64.efi uart=bdf@0:18.1"
|
|
|
|
UP2 serial port setting
|
|
=======================
|
|
|
|
The serial port (ttyS1) in the 40-pin HAT connector is located at ``serial PCI BDF 0:18.1``.
|
|
You can check this from the ``lspci`` output from the initial Clearlinux installation.
|
|
Also you can use ``dmesg | grep tty`` to get its IRQ information for console setting; and update
|
|
SOS bootargs ``console=ttyS1`` in acrn.conf to match with console setting.
|
|
|
|
.. code-block:: none
|
|
|
|
# lspci | grep UART
|
|
00:18.0 . Series HSUART Controller #1 (rev 0b)
|
|
00:18.1 . Series HSUART Controller #2 (rev 0b)
|
|
|
|
# dmesg | grep tty
|
|
dw-apb-uart.8: ttyS0 at MMIO 0x91524000 (irq = 4, base_baud = 115200) is a 16550A
|
|
dw-apb-uart.9: ttyS1 at MMIO 0x91522000 (irq = 5, base_baud = 115200) is a 16550A
|
|
|
|
The second entry associated with ``00:18.1 @irq5`` is the one on the 40-pin HAT connector.
|
|
|
|
UP2 block device
|
|
================
|
|
|
|
The UP2 board has an on-board eMMC device. The device name to be used
|
|
throughout the :ref:`getting_started` therefore is ``/dev/mmcblk0``
|
|
(and ``/dev/mmcblk0pX`` for any partition).
|
|
|
|
The UUID of the partition ``/dev/mmcblk0p3`` can be found by
|
|
|
|
.. code-block:: none
|
|
|
|
# blkid /dev/mmcblk
|
|
|
|
.. note::
|
|
You can also use the device name directly, e.g.: ``root=/dev/mmcblk0p3``
|
|
|
|
Running the hypervisor
|
|
**********************
|
|
|
|
Now that the hypervisor and Service OS have been installed on your UP2 board,
|
|
you can proceed with the rest of the instructions in the
|
|
:ref:`kbl-nuc-sdc` and install the User OS (UOS).
|