The current register names in instr_emul are misleading since the register names
are not VM-specific. Rename VM_REG(_GUEST) to CPU_REG in both the hypervisor and
device model.
v1 -> v2:
* Introduced.
Signed-off-by: Junjie Mao <junjie.mao@intel.com>
An immediate reset or power down will cause a loss of write content.
The cause is the data write to disk is at cache within a short
time window before it's synced to storage media.
An explicit fsync() forces to sync the data to storage to prevent
the data loss of such immediate reset.
Signed-off-by: Huang Yang <yang.huang@intel.com>
Signed-off-by: duminx <minx.du@intel.com>
Acked-by: Eddie Dong <eddie.dong@intel.com>
Misra C required signed/unsigned conversion with cast.
V1->V2:
a.split patch to patch series
Signed-off-by: Huihuang Shi <huihuang.shi@intel.com>
Acked-by: Eddie Dong <eddie.dong@intel.com>
- UOS will boot fail if 'strictio' is enabled ('-e' option), in this
case (with '-e'), device model will block all PIO accesses whose
handlers were not registered, after that, device model program will
exit, hence UOS boot fail.
actually, such kind of accesses exist, e.g. UOS would program
PIT registers (port address: 0x43) if hpet is disabled.
- For debug, we can trap unexpected PIO access in 'default_inout()'
Signed-off-by: Yonghua Huang <yonghua.huang@intel.com>
Signed-off-by: Li, Fei1 <fei1.li@intel.com>
Acked-by: Geoffroy Van Cutsem <geoffroy.vancutsem@intel.com>
Reviewed-by: Jason Chen CJ <jason.cj.chen@intel.com>
Some build environment might has no USER pre-defined. So use id tool to
get builder username instead of USER environemnt.
Also add a version cleanup for tools to keep them updated.
Signed-off-by: Shuo Liu <shuo.a.liu@intel.com>
Acked-by: Geoffroy Van Cutsem <geoffroy.vancutsem@intel.com>
WIFI dev has no FLR, so 'reset' in sysfs calls secondary bus reset,
which cause PCI configuration mess(all FF) then passthrough failure.
To fix it, this patch makes no reset before passthrough by default,
until append this option.
Signed-off-by: Edwin Zhai <edwin.zhai@intel.com>
Acked-by: Anthony Xu <anthony.xu@intel.com>
Use right parameter in launch_uos.sh after updating prefer_msi option
Signed-off-by: Edwin Zhai <edwin.zhai@intel.com>
Acked-by: Anthony Xu <anthony.xu@intel.com>
Current option of removing vGSI capability is global, which exposes
vIOAPIC link for all ptdev even only one need this. This patch makes
it as ptdev local option to lower the system level impact. To keep
vGSI for MSI capable ptdev, just explicitly append ",keep_gsi" in
option list, like "-s 14,passthru,0/e/0,keep_gsi"
Signed-off-by: Edwin Zhai <edwin.zhai@intel.com>
Acked-by: Anthony Xu <anthony.xu@intel.com>
HPET reading is much slower than TSC. Using it will hurt SOS performance
a lot, and then the whole system performance.
Remove the strict assignment from cmdline. Then SOS kernel will pickup
TSC as default clocksource.
Signed-off-by: Shuo Liu <shuo.a.liu@intel.com>
Reviewed-by: Yu Wang <yu1.wang@intel.com>
Acked-by: Anthony Xu <anthony.xu@intel.com>
Previously, either rnd->fd or vbs_k->fd isn't be closed in some cases.
this patch will close them in time.
V2: fix vbs_k->fd leak as well
Signed-off-by: Li Zhijian <lizhijian@cn.fujitsu.com>
- hardcode the devices' GSI info based on the platform
- reject the passthrough if the following requirement is not met
all the PCI devices that are sharing the same GSI should be assigned
to same VM to avoid physical GSI sharing between multiple VMs.
v4 -> v5
* Move the gsi_dev_mapping_tables definition in a separate file
* Add the GSI info that might be used by GPIO
* Update the HW name
v3 - > v4
* Refine the format of raw data to improve the readability
* Remove the redundant code when adding the new dev into the gsi
sharing group
v2 -> v3
* Add the MSI/MSI-x capability check
Do not add the device which supports MSI/MSI-x to the GSI sharing
group.
v1 -> v2
* Update the GSI raw data based on SBL
* Free the resources when gsi sharing violation occurs
* Move the MACRO PCI_BDF(b, d, f) to pci_core.h since passthrough.c
and gsi_sharing.c are both using it
Signed-off-by: Shiqing Gao <shiqing.gao@intel.com>
Reviewed-by: Edwin Zhai <edwin.zhai@intel.com>
Acked-by: Eddie Dong <eddie.dong@intel.com>
Update the vcpu id type as uint16_t for vm_create_vcpu, this
keeps alignment with the updates for the structure acrn_create_vcpu
used by hcall_create_vcpu in the hypervisor.
In the device model, the caller is responsible for vcpu id type
conversion; vcpu id type is uint16_t for external interface in the
current implement.
Signed-off-by: Xiangyang Wu <xiangyang.wu@intel.com>
Acked-by: Eddie Dong <eddie.dong@intel.com>
The device model is a userspace application on SOS to config the
PCI devices for the UOS. Audio mediator device model is to config
the virtual audio PCI device.
Signed-off-by: Zhu Yingjiang <yingjiang.zhu@linux.intel.com>
When enabling GPU passthru for guest, stolen memory needs to be
disabled. This change disables stolen memory in passthru mode.
Signed-off-by: Anitha Chrisanthus <anitha.chrisanthus@intel.com>
Reviewed-by: Gong Zhipeng <zhipeng.gong@intel.com>
To enable GPU passthru, BAR2 allocation had problems when the allocation
is above the 4GB memory.This change is to accomodate the 256MB aperture
allocation in BAR2 to a more managable address.
v2: changed the MEMBASE64 address instead of increasing the mem_size.
Signed-off-by: Anitha Chrisanthus <anitha.chrisanthus@intel.com>
Reviewed-by: Gong Zhipeng <zhipeng.gong@intel.com>
check if there are enough free huge pages(1GB & 2MB now) for UOS,
if no, it will try to reserve more pages for UOS.
here are two examples
1. if system has free huge pages: 1 page of 1GB size, 0 page of 2MB.
one UOS need 2GB + 500MB memory, it will try to reserve one more 1GB
page and 250 2MB pages from system. If enough free system memory, it
can succeed.
2. if system has free huge pages: 4 pages of 1GB size, 0 page of 2MB.
one UOS need 2GB + 500MB, 1GB huge pages 4 > 2, it's enough, and 2 pages
left. It will try to reserve 250 2MB pages from system free memory,
if failed, it will try to release 1 of the 2 left 1GB pages. And then
try to reserve 250 2MB pages.
Signed-off-by: Minggui Cao <minggui.cao@intel.com>
Reviewed-by: Jason Chen CJ <jason.cj.chen@intel.com>
Acked-by: Eddie Dong <eddie.dong@intel.com>
In the hypervisor, physical cpu id is defined as "int" or "uint32_t"
type in the hypervisor. So there are some sign conversion issues
about physical cpu id (pcpu_id) reported by static analysis tool.
Sign conversion violates the rules of MISRA C:2012.
In this patch, define physical cpu id as "uint16_t" type for all
modules in the hypervisor and change related codes. The valid
range of pcpu_id is 0~65534, INVALID_PCPU_ID is defined to the
invalid pcpu_id for error detection, BROADCAST_PCPU_ID is
broadcast pcpu_id used to notify all valid pcpu.
The type of pcpu_id in the struct vcpu and vcpu_id is "int" type,
this will be fixed in another patch.
V1-->V2:
* Change the type of pcpu_id from uint32_t to uint16_t;
* Define INVALID_PCPU_ID for error detection;
* Define BROADCAST_PCPU_ID to notify all valid pcpu.
V2-->V3:
* Update comments for INVALID_PCPU_ID and BROADCAST_PCPU_ID;
* Update addtional pcpu_id;
* Convert hexadecimals to unsigned to meet the type of pcpu_id;
* Clean up for MIN_PCPU_ID and MAX_PCPU_ID, they will be
defined by configuration.
Note: fix bug in the init_lapic(), the pcpu_id shall be less than 8,
this is constraint by implement in the init_lapic().
Signed-off-by: Xiangyang Wu <xiangyang.wu@intel.com>
Acked-by: Eddie Dong <eddie.dong@intel.com>
This patch implements VM monitor operations including stop/suspend/resume.
For other VM monitor operations(pause/unpause/query), IOC mediator would not
register callbacks for them since there is no requirements from VM Manager.
Signed-off-by: Yuan Liu <yuan1.liu@intel.com>
Reviewed-by: Yu Wang <yu1.wang@intel.com>
Reviewed-by: Kevin Tian <kevin.tian@intel.com>
This patch added GVT-g feature and support of plane restriction for APL
NUC platforms.
Signed-off-by: Min He <min.he@intel.com>
Reviewed-by: Zhao Yakui <yakui.zhao@intel.com>
Reviewed-by: Jiang, Fei <fei.jiang@intel.com>
acrn-dm runs to segmentation fault when failed to create VMs with
improper parameters.
If vdevs failed to be created, they are still be freed in deinit(),
and dereference the null pointers leads to segfault.
Signed-off-by: Xinyun Liu <xinyun.liu@intel.com>
Reviewed-by: Yin Fengwei <fengwei.yin@intel.com>
Acked-by: Anthony Xu <anthony.xu@intel.com>
this patch add "reboot_panic=p,w" to command line of SOS to trigger
warm reboot on panic
Signed-off-by: zhouji3x <jianfengx.zhou@intel.com>
Reviewed-by: Yin Fengwei <fengwei.yin@intel.com>
Acked-by: Eddie Dong <eddie.dong@intel.com>
Some APIs of Openssl 1.0 are deprecated in Openssl 1.1+.
Two different API implementations are adaptable to both
Openssl 1.1- and 1.1+.
Fixes: #305
Signed-off-by: Huang Yang <yang.huang@intel.com>
Signed-off-by: Du Min <minx.du@intel.com>
Acked-by: Eddie Dong <eddie.dong@intel.com>
when add/create vcpu failed, before it just exits,
and the resource will not released; now if failed,
let DM release the resource.
Signed-off-by: Minggui Cao <minggui.cao@intel.com>
Reviewed-by: Yin Fengwei <fengwei.yin@intel.com>
Acked-by: Eddie Dong <eddie.dong@intel.com>
When initial_modeset is enabled, will check EDID in early stage,
while sometime didn't get EDID in time through I2C, and will cause
CRTC not used correctly in some corner cases. Then we need force
enabling two HDMI connectors to attach CRTC in initial modeset stage.
Signed-off-by: Fei Jiang <fei.jiang@intel.com>
Reviewed-by: Zhao, Yakui <yakui.zhao@intel.com>
Reviewed-by: Min He <min.he@intel.com>
pincpu and vmexit_pause both aligned to lower p, it is a bug, vmexit_pause should align with P(upper).
Missing enable_bvmcons usage so add -b in help prints.
remove redundant tab blank to keep same indentation.
Signed-off-by: Chris Ye <chris.ye@intel.com>
update to systemd config files so that the bridge will be up
when systemd-networkd is started.
Signed-off-by: Tan Shen Joon <shen.joon.tan@intel.com>
Reviewed-by: Jack Ren <jack.ren@intel.com>
This patch fix some potential crash issues, like wild
pointers access, buffer overflow and etc.
Change-Id: Iddd8e1820da426adc6b9b4d9da9e44017d9f365c
Signed-off-by: Xiaoguang Wu <xiaoguang.wu@intel.com>
Reviewed-by: Yu Wang <yu1.wang@intel.com>
Acked-by: Eddie Dong <eddie.dong@intel.com>
With current implementation:
vm_init_vdevs only handles the negative error code, while passthru_init
returns positive error code when error occurs.
This causes unexpected dm crash since the real error is not being
handled properly.
What this patch does:
Change the error code to be negative value in passthru_init because it
is common in Linux kernel to return negative value when error occurs.
v2 -> v3
* add more comments about the reason to convert the return value
v1 -> v2:
* add a wrapper API to convert the error returned from pci_system_init
to the ERROR we defined in DM
* use the defined errno as the return value rather than -1
Signed-off-by: Shiqing Gao <shiqing.gao@intel.com>
Acked-by: Eddie Dong <eddie.dong@intel.com>
On SBL platform, UOS bsp always starts from realmode, which requires
the support of vSBL.
Boot kernel directly by -U option is no longer supported.
Remove -U option in launch script.
Signed-off-by: Binbin Wu <binbin.wu@intel.com>
Reviewed-by: Zhao Yakui <yakui.zhao@intel.com>
Reviewed-by: Edwin Zhai <edwin.zhai@intel.com>
Acked-by: Eddie Dong <eddie.dong@intel.com>
The Intel Trace Hub (aka. North Peak, NPK) is a trace aggregator for
Software, Firmware, and Hardware. On the virtualization platform, it
can be used to output the traces from SOS/UOS/Hypervisor/FW together
with unified timestamps.
There are 2 software visible MMIO space in the npk pci device. One is
the CSR which maps the configuration registers, and the other is the
STMR which is organized as many Masters, and used to send the traces.
Each Master has a fixed number of Channels, which is 128 on GP. Each
channel occupies 64B, so the offset of each Master is 8K (64B*128).
Here is the detailed layout of STMR:
M=NPK_SW_MSTR_STP (1024 on GP)
+-------------------+
| m[M],c[C-1] |
Base(M,C-1) +-------------------+
| ... |
+-------------------+
| m[M],c[0] |
Base(M,0) +-------------------+
| ... |
+-------------------+
| m[i+1],c[1] |
Base(i+1,1) +-------------------+
| m[i+1],c[0] |
Base(i+1,0) +-------------------+
| ... |
+-------------------+
| m[i],c[1] |
Base(i,1)=SW_BAR+0x40 +-------------------+
| m[i],c[0] | 64B
Base(i,0)=SW_BAR +-------------------+
i=NPK_SW_MSTR_STRT (256 on GP)
CSR and STMR are treated differently in npk virtualization because:
1. CSR configuration should come from just one OS, instead of each OS.
In our case, it should come from SOS.
2. For performance and timing concern, the traces from each OS should
be written to STMR directly.
Based on these, the npk virtualization is implemented in this way:
1. The physical CSR is owned by SOS, and dm/npk emulates a software
one for the UOS, to keep the npk driver on UOS unchanged. Some CSR
initial values are configured to make the UOS npk driver think it
is working on a real npk. The CSR configuration from UOS is ignored
by dm, and it will not bring any side-effect. Because traces are the
only things needed from UOS, the location to send traces to and the
trace format are not affected by the CSR configuration.
2. Part of the physical STMR will be reserved for the SOS, and the
others will be passed through to the UOS, so that the UOS can write
the traces to the MMIO space directly.
A parameter is needed to indicate the offset and size of the Masters
to pass through to the UOS. For example, "-s 0:2,npk,512/256", there
are 256 Masters from #768 (256+512, #256 is the starting Master for
software tracing) passed through to the UOS.
CSR STMR
SOS: +--------------+ +----------------------------------+
| physical CSR | | Reserved for SOS | |
+--------------+ +----------------------------------+
UOS: +--------------+ +---------------+
| sw CSR by dm | | mapped to UOS |
+--------------+ +---------------+
Here is an overall flow about how it works.
1. System boots up, and the npk driver on SOS is loaded.
2. The dm is launched with parameters to enable npk virtualization.
3. The dm/npk sets up a bar for CSR, and some values are initialized
based on the parameters, for example, the total number of Masters for
the UOS.
4. The dm/npk sets up a bar for STMR, and maps part of the physical
STMR to it with an offset, according to the parameters.
5. The UOS boots up, and the native npk driver on the UOS is loaded.
6. Enable the traces from UOS, and the traces are written directly to
STMR, but not output by npk for now.
7. Enable the npk output on SOS, and now the traces are output by npk
to the selected target.
8. If the memory is the selected target, the traces can be retrieved
from memory on SOS, after stopping the traces.
Signed-off-by: Zhi Jin <zhi.jin@intel.com>
Reviewed-by: Zhang Di <di.zhang@intel.com>
Acked-by: Eddie Dong <eddie.dong@intel.com>
When connecting three monitors to MRB, we will assign the first one to
SOS and assign remaining ones to UOS.
Signed-off-by: Min He <min.he@intel.com>
Reviewed-by: Zhao Yakui <yakui.zhao@intel.com>
Create a new diectory bios in devicemodel
Add vSBL binary in bios directory.
- VSBL.bin: release version of vSBL
- VSBL_debug.bin: debug version of vSBL
Signed-off-by: Binbin Wu <binbin.wu@intel.com>
Reviewed-by: Jack Ren <jack.ren@intel.com>
Acked-by: Eddie Dong <eddie.dong@intel.com>
Now the IPU devices are always enabled. But they don't exist on some
boards. In such case some errors are warned and the system can't be booted.
Signed-off-by: Zhao Yakui <yakui.zhao@intel.com>
Reviewed-by: Yin FengWei <fengwei.yin@intel.com>
Reviewed-by: Jason Chen CJ <jason.cj.chen@intel.com>
Enable IOC for android on MRB by default.
Signed-off-by: Yuan Liu <yuan1.liu@intel.com>
Reviewed-by: Yu Wang <yu1.wang@intel.com>
Reviewed-by: Like Yan <like.yan@intel.com>
Acked-by: Eddie Dong <eddie.dong@intel.com>
vsbl layout has been changed.
Previously, vsbl start from 64bit mode.
This patch changes the vsbl load code according to the
layout change of vSBL.
The new vsbl binary added reset vector support.
It will start from reset vector in real mode.
Signed-off-by: Binbin Wu <binbin.wu@intel.com>
Reviewed-by: Kevin Tian <kevin.tian@intel.com>
Acked-by: Xu, Anthony <anthony.xu@intel.com>
For the platform without virtual bootloader, dm will load uos kernel
directly, and hv will set rip according to uos kernel entry.
In current code, uos bsp starts from 64bit mode, so 64bit kernel entry
is used.
This patch series sets uos bsp to protected mode on such platform, so
32bit kernel entry is choosed.
Signed-off-by: Binbin Wu <binbin.wu@intel.com>
Reviewed-by: Eddie Dong <eddie.dong@intel.com>
Reviewed-by: Kevin Tian <kevin.tian@intel.com>
Acked-by: Xu, Anthony <anthony.xu@intel.com>
Signed-off-by: Yan, Like <like.yan@intel.com>
Reviewed-by: Yuan Liu <yuan1.liu@intel.com>
Reviewed-by: Yu Wang <yu1.wang@intel.com>
Reviewed-by: Zhao Yakui <yakui.zhao@intel.com>
Acked-by: Eddie Dong <eddie.dong@intel.com>
To avoid PTY device symbol link failure due to non-exist directory passed from
parameter. Add check_dir function to check the directory and create it if not
exist.
Signed-off-by: Yuan Liu <yuan1.liu@intel.com>
Reviewed-by: Yu Wang <yu1.wang@intel.com>
Reviewed-by: Zhao Yakui <yakui.zhao@intel.com>
Acked-by: Eddie Dong <eddie.dong@intel.com>
Fixes a recent PR #311 that added a new API but the doxygen comments for
one of the parameters didn't match the parameter name.
Signed-off-by: David B. Kinder <david.b.kinder@intel.com>
Junjie Mao