IOC mediator should keep sending acnrd boot reason until received
UOS heartbeat init message, then turn to send SOS wakeup reason
through read native cbc lifecycle cdev.
Tracked-On: #1727
Signed-off-by: Yuan Liu <yuan1.liu@intel.com>
Acked-by: Yu Wang <yu1.wang@intel.com>
Accoring to xHCI spec, there are some TRBs with zero data length
which used to pass command to xHCI. In the DM, those TRBs should
not be sent to native device through libusb. The logic in the
current implentation fails to process some corner cases, this
patch is used to fix it.
Tracked-On: #1639
Signed-off-by: Xiaoguang Wu <xiaoguang.wu@intel.com>
Reviewed-by: Liang Yang <liang3.yang@intel.com>
Acked-by: Yu Wang <yu1.wang@intel.com>
- remove ASSERT & DEASSET IRQ line IOCTLs
- remove PULSE IRQ line IOCTLs, use set/clear
IRQ line instead.
- Use IC_SET_IRQLINE to set or clear IRQ line
Tracked-On: #861
Signed-off-by: Yonghua Huang <yonghua.huang@intel.com>
Reviewed-by: Jason Chen CJ <jason.cj.chen@intel.com>
Reviewed-by: Eddie Dong <eddie.dong@intel.com>
Acked-by: Anthony Xu <anthony.xu@intel.com>
When the LINK type TRB are received, it should not be counted as
valid date block to give libusb. This patch is used to fix it.
Tracked-On: #1567
Signed-off-by: Xiaoguang Wu <xiaoguang.wu@intel.com>
Reviewed-by: Liang Yang <liang3.yang@intel.com>
Acked-by: Yu Wang <yu1.wang@intel.com>
physical RPMB is accessed if "phisycal_rpmb" is specified
in launch.sh.
Also it reserves some RPMB area with a fixed size(32KB) for
AttKB and future usage, which is RO for UOS.
Tracked-On: #1544
Signed-off-by: Huang, Yang <yang.huang@intel.com>
Acked-by: Zhu Bing <bing.zhu@intel.com>
This patch is one workaround to resolve a crash issue for certain brand
touch screen (eGalaxTouch EXC7200-7368v1.01). The formal fix should
follow the xHCI spec to stop xfer and generate transfer completed event
trb prior to Stop Endpoint Command complete event trb. It should be a
big change and for short term, do nothing for the stop endpoint command
which is no other side effect be observed so far.
Tracked-On: #1413
Signed-off-by: Xiaoguang Wu <xiaoguang.wu@intel.com>
Reviewed-by: Liang Yang <liang3.yang@intel.com>
Acked-by: Yu Wang <yu1.wang@intel.com>
This patch is used to support emulation of multiple layers of hubs
under Flat Mode.
Tracked-On: #1434
Signed-off-by: Xiaoguang Wu <xiaoguang.wu@intel.com>
Signed-off-by: Liang Yang <liang3.yang@intel.com>
Acked-by: Yu Wang <yu1.wang@intel.com>
This patch is used to enable multiple hubs in single layer under
Flat Mode.
Tracked-On: #1434
Signed-off-by: Liang Yang <liang3.yang@intel.com>
Signed-off-by: Xiaoguang Wu <xiaoguang.wu@intel.com>
Acked-by: Yu Wang <yu1.wang@intel.com>
There are many places in USB emulation implementation to get
native USB device infomation, and the related codes are long
and repeated many times. This patch introduces function
usb_get_native_devinfo to remove redundent codes for the
purpose mentioned above.
Tracked-On: #1434
Signed-off-by: Xiaoguang Wu <xiaoguang.wu@intel.com>
Signed-off-by: Liang Yang <liang3.yang@intel.com>
Acked-by: Yu Wang <yu1.wang@intel.com>
This patch introduce struct usb_devpath to indentify uniquely an USB
device, which is basic element for multiple hub support.
Tracked-On: #1434
Signed-off-by: Liang Yang <liang3.yang@intel.com>
Signed-off-by: Xiaoguang Wu <xiaoguang.wu@intel.com>
Acked-by: Yu Wang <yu1.wang@intel.com>
Previous design use bus and port(root hub port) for the identification
to the native USB device. It cannot work properly under the multi-hub
situation due to external USB hub is introduced.
This patch removes old hub implementation code, and subsequent patches
will be add support for mutiple hubs.
Tracked-On: #1434
Signed-off-by: Liang Yang <liang3.yang@intel.com>
Signed-off-by: Xiaoguang Wu <xiaoguang.wu@intel.com>
Acked-by: Yu Wang <yu1.wang@intel.com>
This patch addes the debugexit function to DM. If it's enabled
by DM cmdline (by add --debugexit), the guest could write a
32bit value to port 0xF4 to trigger guest shutdown.
Tracked-on: #1465
Signed-off-by: Yin Fengwei <fengwei.yin@intel.com>
Reviewed-by: Jason Chen CJ <jason.cj.chen@intel.com>
Acked-by: Yu Wang <yu1.wang@intel.com>
Current RTC emulation is based on sigevent mechanism, replace with
acrn_timer API which based on timerfd/epoll mechanism to avoid
potential resource accessing conflict in the async thread.
Tracked-On: #1489
Signed-off-by: Victor Sun <victor.sun@intel.com>
Reviewed-by: Jian Jun Chen <jian.jun.chen@intel.com>
Acked-by: Yin Fengwei <fengwei.yin@intel.com>
NHLT table contains the settings some audio drivers need.
An ACPI method is used to get NHLT table address & length.
In current DM code, the NHLT talbe length in the ACPI method
is hardcoded, which will cause troubles when the length of the
table changed.
This patch replaces the hardcoded NHLT table length according to
the table length read from SOS.
Tracked-On: #1461
Signed-off-by: Binbin Wu <binbin.wu@intel.com>
Acked-by: Yin Fengwei <fengwei.yin@intel.com>
Replace strtok function with strsep function.
Tracked-On: #1401
Signed-off-by: Yuan Liu <yuan1.liu@intel.com>
Reviewed-by: Shuo Liu <shuo.a.liu@intel.com>
Acked-by: Yu Wang <yu1.wang@intel.com>
Return value check for snprintf function.
Tracked-On: #1401
Signed-off-by: Yuan Liu <yuan1.liu@intel.com>
Reviewed-by: Shuo Liu <shuo.a.liu@intel.com>
Acked-by: Yu Wang <yu1.wang@intel.com>
The patch resolves a bug that signal SteeringWheelSpeechCtrlBtn can not be
received in UOS. the rootcause is signal SteeringWheelSpeechCtrlBtn and
signal SteeringWheelPauseBtn are combined into one multi-signal message and
signal SteeringWheelPauseBtn is not defined.
To fix this, add SteeringWheelPauseBtn definition.
Tracked-On: #1410
Signed-off-by: Yuan Liu <yuan1.liu@intel.com>
Acked-by: Yu Wang <yu1.wang@intel.com>
vPIT is used as a source of system timer by UEFI (e.g. OVMF).
This is ported from Bhyve, with a few changes:
- move to user space, using POSIX timer
- support timer mode 3
- improve the emulation of OUT and STATUS byte
- improve the emulation of counter behavior
- improve the emulation of CE update in periodic mode
- treat CR == 0 as 0x10000
Origin: FreeBSD
License: BSD-3-Clause
URL: https://svnweb.freebsd.org/
commit: 283291
Purpose: Adding vPIT support.
Maintained-by: External
Tracked-On: #1392
Signed-off-by: Peter Fang <peter.fang@intel.com>
Acked-by: Yin Fengwei <fengwei.yin@intel.com>
Some firmware (e.g. UEFI) uses RTC CMOS to fetch the system's memory
configuration. Put lowmem / highmem info in the designated area.
This is a port of Bhyve vRTC's user-space logic.
v1 -> v2:
* move KB/MB/GB to macros.h
* move nvram offset definitions to rtc.h
Tracked-On: #1390
Signed-off-by: Peter Fang <peter.fang@intel.com>
Acked-by: Anthony Xu <anthony.xu@intel.com>
When USB hub is disconnected, its connection status is not cleared
in the DM, this defect will cause the related assigned port could
not be used any more.
This patch is used fix this issue.
Signed-off-by: Xiaoguang Wu <xiaoguang.wu@intel.com>
Reviewed-by: Liang Yang <liang3.yang@intel.com>
Acked-by: Yu Wang <yu1.wang@intel.com>
Tracked-On: #1365
CAVS audio driver depends on the NHLT table to get topology info.
Enable NHLT table in DM for audio passthrough.
Also increase the size reserved for NHLT in ACPI table from 2048B to 2560B.
Tracked-On: #1284
Signed-off-by: Binbin Wu <binbin.wu@intel.com>
Reviewed-by: Geoffroy Van Cutsem <geoffroy.vancutsem@intel.com>
Acked-by: Yin Fengwei <fengwei.yin@intel.com>
USB device is connected before UOS is booted up, this scenario is
called 'cold plug' for easy to refer.
Under 'cold plug' situation, the libusb will not report 'connect'
event to device model, hence UOS will not discover 'cold plugged'
device.
This patch add support to fix this issue.
Signed-off-by: Xiaoguang Wu <xiaoguang.wu@intel.com>
Reviewed-by: Liang Yang <liang3.yang@intel.com>
Acked-by: Yu Wang <yu1.wang@intel.com>
Tracked-On: #1242
Flat Mode for hub emulation means DM emulates USB devices under hub but
hide hub itself. Under this design the Guest OS cannot see any emulated
hub. So in the perspective of Guest OS, all the emulated devices are
under root hub.
This patch is used to enable feature as mentioned above. And please NOTE,
it is the initial version of hub flat Mode hub emulation, there are one
limitation: only one physical hub is supported. If second physical hub is
connected, the connect and disconnect behavior in second hub may affect
the function of first emulated hub.
The USB HUB device model should be the final long term solution, but it is
very complex. Use flat mode HUB emulation as the short term solution first
to support some USB touch devices which integrated internal HUB.
Signed-off-by: Liang Yang <liang3.yang@intel.com>
Reviewed-by: Xiaoguang Wu <xiaoguang.wu@intel.com>
Acked-by: Yu Wang <yu1.wang@intel.com>
Tracked-On: #1243
This patch implements RTC feature that UOS can set RTC wakeup timer
to IOC firmware with a specific time before enter S3/S5. IOC mediator
also needs to indicate RTC wakeup reason to UOS after exit S3/S5.
Tracked-On: #1213
Signed-off-by: Yuan Liu <yuan1.liu@intel.com>
Acked-by: Yu Wang <yu1.wang@intel.com>
In the current implementation sigev_notify is configured as
SIGEV_THREAD. When timer expires an async thread is created and
the registered timer callback is called in the context of this
thread. vrtc_update_timer will access the global data vrtc. There
is a race condition that vrtc is freed when deinit and then a timer
expires. In this case vrtc_update_timer will access a freed buffer
which causes problem such as heap corruption and segment fault.
In this patch signal model is used when timer is created. The signal
is masked and a signalfd is used to poll on it with mevent. This avoids
the race condition.
Signed-off-by: Jian Jun Chen <jian.jun.chen@intel.com>
Acked-by: Yin Fengwei <fengwei.yin@intel.com>
Tracked-On: #1185
This patch fixes an issue that CBC signal channel
is inactive after SOS resuming, it leads to IOC mediator
cannot transfer any signals between UOS and SOS. So IOC
mediator sends the open channel command to activate CBC
signal channel after resuming.
Tracked-On: #1115
Signed-off-by: Yuan Liu <yuan1.liu@intel.com>
Acked-by: Yu Wang <yu1.wang@intel.com>
The whole vmctx will be cleared during cold reset.
cmos data should not be cleared during cold reset.
Move cmos data out of vmctx.
Tracked-On: #1118
Signed-off-by: Binbin Wu <binbin.wu@intel.com>
Acked-by: Yin Fengwei <fengwei.yin@intel.com>
CMOS offset from 0x20 to 0x9F is used to store rpmb key information.
vsbl loader will init vrpmb key in CMOS when boot/reboot.
vsbl loader will not init vrpmb key during S3 resume.
vsbl will read vrpmb key via CMOS interface.
After reading, the key value is cleared in CMOS. So the key can only be
read once until next boot.
Signed-off-by: Binbin Wu <binbin.wu@intel.com>
Acked-by: Yin Fengwei <fengwei.yin@intel.com>
Current design cannot get physical USB device information without
the creation of pci_xhci_dev_emu. This brings some difficulties in
certain situations, hence struct usb_native_devinfo is introduced
to describe neccessary information to solve this trouble.
Signed-off-by: Xiaoguang Wu <xiaoguang.wu@intel.com>
Reviewed-by: Liang Yang <liang3.yang@intel.com>
Acked-by: Yu Wang <yu1.wang@intel.com>
We do:
- pause target vm
- suspend all virtual devices
- wait for resume notification
- resume all virtual devices
- reset target vm
Signed-off-by: Yin Fengwei <fengwei.yin@intel.com>
Acked-by: Eddie Dong <eddie.dong@intel.com>
This patch adds new signals about parking brake and Hvac in the signal
definition and signal whitelist.
Signed-off-by: Yuan Liu <yuan1.liu@intel.com>
Acked-by: Yu Wang <yu1.wang@intel.com>
This patch resolves IOC mediator deinit function is blocked due to IOC mediator
core thread enters into sleep by epoll_wait, then pthread_join cannot return.
Trigger an event to wakeup core thread when IOC mediator deinit is invoked.
Signed-off-by: Yuan Liu <yuan1.liu@intel.com>
Reviewed-by: Liang Yang <liang3.yang@intel.com>
Acked-by: Yu Wang <yu1.wang@intel.com>
Enable isochronous transfer to support related USB devices
Change-Id: Id9fe0714e937fafc47de090ba6d349713cbe1b8b
Tracked-On:
Signed-off-by: Xiaoguang Wu <xiaoguang.wu@intel.com>
Reviewed-by: Liang Yang <liang3.yang@intel.com>
Acked-by: Yu Wang <yu1.wang@intel.com>
In the process of implementation for USB isochronous transfer, the
timeout (100ms) is not enough for Plantronics USB headset. So pass
longer timeout (300ms) to function libusb_control_transfer will
make USB headset of Plantronics work.
This change only results a longer execution time in ENUMERATION process
for few devices like Plantronics USB headset which need more time to do
its internal operations. For most USB devices, time less than 100ms are
enough to complete the execution of libusb_control_transfer. So basically
it will not affect the whole system performance.
In the long term, a better solution (eg: async control transfer) will be
introduced to replace current implementation.
Change-Id: I380e0cc337ec5741b1e4ce989abacce826b7dde4
Tracked-On:
Signed-off-by: Xiaoguang Wu <xiaoguang.wu@intel.com>
Reviewed-by: Liang Yang <liang3.yang@intel.com>
Acked-by: Yu Wang <yu1.wang@intel.com>
BCD code is USB Specification Release Number in Binaray-Coded
Decimal. Add some BCD codes for some USB devices.
Change-Id: I40f04ef2ebaf5b0da554ff8f432415e8e3cebe01
Tracked-On:
Signed-off-by: Xiaoguang Wu <xiaoguang.wu@intel.com>
Reviewed-by: Liang Yang <liang3.yang@intel.com>
Acked-by: Yu Wang <yu1.wang@intel.com>
Handle the LIBUSB_TRANSFER_STALL error comes from libusb.
Change-Id: Id6911e9aaffafb256def5265a0ed9778b147d99a
Tracked-On:
Signed-off-by: Xiaoguang Wu <xiaoguang.wu@intel.com>
Reviewed-by: Liang Yang <liang3.yang@intel.com>
Acked-by: Yu Wang <yu1.wang@intel.com>
Current ring buffer processing logic assumes every transaction
will be submited to physical device before next transaction
coming. So it use two states 0 (free) and 1 (used) to represent
the state of every data block in the ring buffer. With the help
of the two state, the ring buffer could accept and process data
normally.
But this logic is not proper for ISOC transfer, which generally
submits many transactions even none of them arrive the physical
device. So this patch uses three values to represent the state
of data block in the ring buffer:
USB_XFER_BLK_FREE: this block could be filled with new data;
USB_XFER_BLK_HANDLING: this block is submited to physical device
but response from device is still not received;
USB_XFER_BLK_HANDLED: this block has been processed by physical
device.
The new logic will do different things for each state, which will
make the ISOC transfer work successfully.
Change-Id: I5559cae24c739633289742d64dd51751797b81a7
Tracked-On:
Signed-off-by: Xiaoguang Wu <xiaoguang.wu@intel.com>
Reviewed-by: Liang Yang <liang3.yang@intel.com>
Acked-by: Yu Wang <yu1.wang@intel.com>
The xHCI speed emulation is not right, which will cause failure
during enumeration of certain USB device. This patch is used to
fix it.
Change-Id: I2d996298983882ed6921a75a10dec9e8684a393e
Tracked-On:
Signed-off-by: Xiaoguang Wu <xiaoguang.wu@intel.com>
Reviewed-by: Liang Yang <liang3.yang@intel.com>
Acked-by: Yu Wang <yu1.wang@intel.com>
Refine the logic of usb interface state transition.
The libusb uses two pair of APIs to deal with usb interface:
1. libusb_claim_interface & libusb_detach_kernel_driver;
2. libusb_release_interface & libusb_attach_kernel_driver.
The calling sequences of those APIs are very important, so this
patch add some error handling code to make this process more
robust.
Change-Id: I0f7950aae806dee9a21f16cc293f51609eede0d8
Tracked-On:
Signed-off-by: Xiaoguang Wu <xiaoguang.wu@intel.com>
Reviewed-by: Liang Yang <liang3.yang@intel.com>
Acked-by: Yu Wang <yu1.wang@intel.com>
This patch is used to add support for USB 3.0 devices. Currently
USB 3.0 disk is supported and tested successfully.
Change-Id: I3fbfbe9c28bc4b14af0417104f8fa822f9758908
Tracked-On:
Signed-off-by: Xiaoguang Wu <xiaoguang.wu@intel.com>
Reviewed-by: Liang Yang <liang3.yang@intel.com>
Acked-by: Yu Wang <yu1.wang@intel.com>
There are many 'short packet' warnings in the UOS kernel dmesg output,
which are result from bad short packet identification algorithm. This
patch is used to fix it.
Change-Id: Idfa0b87fc96893b80d5c9fe8dab4db35aa5bfe84
Tracked-On:
Signed-off-by: Xiaoguang Wu <xiaoguang.wu@intel.com>
Reviewed-by: Liang Yang <liang3.yang@intel.com>
Acked-by: Yu Wang <yu1.wang@intel.com>
Original code will reset the whole USB device when xHCI Reset
Endpoint command is received, this behavior is not right. This
patch is used to fix it.
And according to xhci spec 4.6.8, if the endpoint is not in the
halted state, xHC should reject to execute this command and the
Context State Error should be returned. This patch also add this
logic.
Change-Id: I55a5918148d82d103fb3eb27d582f9676f9f61d3
Tracked-On:
Signed-off-by: Xiaoguang Wu <xiaoguang.wu@intel.com>
Reviewed-by: Liang Yang <liang3.yang@intel.com>
Acked-by: Yu Wang <yu1.wang@intel.com>
Mainly change the logs for transfer submission and completion,
which are very important parts in USB emulation code.
Change-Id: I4e04f1426e164ca3693e70946ed51380201e49ee
Signed-off-by: Xiaoguang Wu <xiaoguang.wu@intel.com>
Reviewed-by: Liang Yang <liang3.yang@intel.com>
Acked-by: Yu Wang <yu1.wang@intel.com>
This patch correct the USB request type which set wrong direction in
original code. It caused these important usb control transfer packets
send to phsical USB devices via libusb_control_transfer instead of
calling standard libusb APIs, likes libusb_set_configuration. From
libusb document, this is not the correct way:
"You should always use this function rather than formulating your own
SET_CONFIGURATION control request. This is because the underlying
operating system needs to know when such changes happen."
Change-Id: I7a6aade326220bee3b685086584920dacd37f87c
Signed-off-by: Xiaoguang Wu <xiaoguang.wu@intel.com>
Reviewed-by: Liang Yang <liang3.yang@intel.com>
Acked-by: Yu Wang <yu1.wang@intel.com>
Guest has erquirement to support system/full reboot and S3. Which could
trigger different reset path in guest
Signed-off-by: Yin Fengwei <fengwei.yin@intel.com>
Acked-by: Anthony Xu <anthony.xu@intel.com>
Yuan Liu