doc: add more details to the Kata Containers with ACRN tutorial
* Add more details about Kata Containers and ACRN in the introduction * Adjust and correct some of the instructions Signed-off-by: Geoffroy Van Cutsem <geoffroy.vancutsem@intel.com>
This commit is contained in:
parent
933e2178d0
commit
e25a2bf80c
|
@ -1,10 +1,15 @@
|
|||
.. _run-kata-containers:
|
||||
|
||||
Run Kata containers on a Service VM
|
||||
Run Kata Containers on a Service VM
|
||||
###################################
|
||||
|
||||
This tutorial describes how to install, configure, and run Kata containers on
|
||||
the ACRN Service VM.
|
||||
This tutorial describes how to install, configure, and run `Kata Containers
|
||||
<https://katacontainers.io/>`_ on the ACRN Service VM. In this configuration,
|
||||
Kata Containers leverage the ACRN hypervisor instead of QEMU which is used by
|
||||
default. Refer to the `Kata Containers with ACRN
|
||||
<https://drive.google.com/file/d/1ZrqM5ouWUJA0FeIWhU_aitEJe8781rpe/view?usp=sharing>`_
|
||||
presentation from a previous ACRN Project Technical Community Meeting for more
|
||||
details on Kata Containers and how the integration with ACRN has been done.
|
||||
|
||||
Pre-Requisites
|
||||
**************
|
||||
|
@ -15,16 +20,14 @@ Pre-Requisites
|
|||
#. Refer to the :ref:`ACRN supported hardware <hardware>`.
|
||||
#. For a default prebuilt ACRN binary in the E2E package, you must have 4 CPU cores or enable "CPU Hyper-Threading” in order to have 4 CPU threads for 2 CPU cores.
|
||||
#. Follow :ref:`these instructions <quick-setup-guide>` to set up the ACRN Service VM.
|
||||
#. Build the ACRN kernel to enable the ``macvtap`` function:
|
||||
#. Build the ACRN kernel (required to support ``macvtap``, enabled by default since `247a3ba9243b <https://github.com/projectacrn/acrn-kernel/commit/247a3ba9243b1fd8c2d763158d55f8791a9cac94>`_)
|
||||
|
||||
.. code-block:: none
|
||||
|
||||
$ git clone https://github.com/projectacrn/acrn-kernel.git
|
||||
$ cd acrn-kernel
|
||||
$ cp kernel_config_sos .config
|
||||
$ sed -i "s/# CONFIG_MACVLAN is not set/CONFIG_MACVLAN=y/" .config
|
||||
$ sed -i '$ i CONFIG_MACVTAP=y' .config
|
||||
$ make clean && make olddefconfig && make && sudo make modules_install INSTALL_MOD_PATH=out/
|
||||
$ make clean && make olddefconfig && make && make modules_install INSTALL_MOD_PATH=out/
|
||||
|
||||
Log in to the Service VM and use the new ACRN kernel:
|
||||
|
||||
|
@ -36,7 +39,10 @@ Pre-Requisites
|
|||
$ conf_file=`sed -n '$ s/default //p' /mnt/loader/loader.conf`.conf
|
||||
$ kernel_img=`sed -n 2p /mnt/loader/entries/$conf_file | cut -d'/' -f4`
|
||||
$ sed -i "s/$kernel_img/bzImage/g" /mnt/loader/entries/$conf_file
|
||||
$ sync && umount /mnt && sudo reboot
|
||||
$ sync && sudo umount /mnt && reboot
|
||||
|
||||
.. note::
|
||||
Adjust the EFI System Partition (ESP) device node (``/dev/sda1`` in the example above) to match your system setup.
|
||||
|
||||
Configure Kata on ACRN
|
||||
**********************
|
||||
|
|
Loading…
Reference in New Issue